Message-ID: <a6468707-583f-4ce9-837d-16bb9079a0f6@starfivetech.com>
Date:   Thu, 7 Dec 2023 10:16:57 +0800
From:   Keith Zhao <keith.zhao@...rfivetech.com>
To:     Dave Stevenson <dave.stevenson@...pberrypi.com>
CC:     Stefan Wahren <wahrenst@....net>,
        Shengyang Chen <shengyang.chen@...rfivetech.com>,
        "devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
        "dri-devel@...ts.freedesktop.org" <dri-devel@...ts.freedesktop.org>,
        "thierry.reding@...il.com" <thierry.reding@...il.com>,
        "neil.armstrong@...aro.org" <neil.armstrong@...aro.org>,
        "conor+dt@...nel.org" <conor+dt@...nel.org>,
        "tzimmermann@...e.de" <tzimmermann@...e.de>,
        "krzysztof.kozlowski+dt@...aro.org" 
        <krzysztof.kozlowski+dt@...aro.org>,
        "sam@...nborg.org" <sam@...nborg.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "mripard@...nel.org" <mripard@...nel.org>,
        Jack Zhu <jack.zhu@...rfivetech.com>,
        "robh+dt@...nel.org" <robh+dt@...nel.org>,
        "bcm-kernel-feedback-list@...adcom.com" 
        <bcm-kernel-feedback-list@...adcom.com>,
        "linux-rpi-kernel@...ts.infradead.org" 
        <linux-rpi-kernel@...ts.infradead.org>,
        "florian.fainelli@...adcom.com" <florian.fainelli@...adcom.com>,
        "quic_jesszhan@...cinc.com" <quic_jesszhan@...cinc.com>,
        Changhuang Liang <changhuang.liang@...rfivetech.com>,
        "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v1 0/2] Add waveshare 7inch touchscreen panel support



On 2023/12/6 22:56, Dave Stevenson wrote:
> Hi Keith
> 
> On Wed, 6 Dec 2023 at 08:55, Keith Zhao <keith.zhao@...rfivetech.com> wrote:
>>
>>
>>
>> On 2023/11/25 0:04, Dave Stevenson wrote:
>> > On Fri, 24 Nov 2023 at 15:00, Stefan Wahren <wahrenst@....net> wrote:
>> >>
>> >> Hi Shengyang,
>> >>
>> >> [fix address of Emma]
>> >
>> > Not merged to master yet, but Emma has stepped back from maintenance.
>> > https://lists.freedesktop.org/archives/dri-devel/2023-October/428829.html
>> > Dropped from the cc.
>> >
>> >> Am 24.11.23 um 11:44 schrieb Shengyang Chen:
>> >> > This patchset adds waveshare 7inch touchscreen panel support
>> >> > for the StarFive JH7110 SoC.
>> >> >
>> >> > Patch 1 add new compatible for the raspberrypi panel driver and its dt-binding.
>> >> > Patch 2 add new display mode and new probing process for raspberrypi panel driver.
>> >> >
>> >> > Waveshare 7inch touchscreen panel is a kind of raspberrypi panel
>> >> > which can be drived by raspberrypi panel driver.
>> >> >
>> >> > The series has been tested on the VisionFive 2 board.
>> >> surprisingly i was recently working on the official Raspberry Pi
>> >> touchscreen and was able to get it running the new way.
>> >>
>> >> What do i mean with the new way. There is almost nothing special to the
>> >> Raspberry Pi touchscreen, so we should try to use/extend existing
>> >> components like:
>> >>
>> >> CONFIG_DRM_PANEL_SIMPLE
>> >> CONFIG_TOUCHSCREEN_EDT_FT5X06
>> >> CONFIG_DRM_TOSHIBA_TC358762
>> >>
>> >> The only special part is the Attiny on the connector PCB which requires:
>> >>
>> >> CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY
>> >>
>> >> So the whole point is to avoid writing monolitic drivers for simple
>> >> panel like that.
>> >>
>> >> There is a WIP branch based on top of Linux 6.7-rcX, which should
>> >> demonstrate this approach [1]. Unfortunately it is not ready for
>> >> upstreaming, but it has been tested on a Raspberry Pi 3 B Plus. Maybe
>> >> this is helpful for your case.
>> >>
>> >> Actually i consider panel-raspberrypi-touchscreen.c as a dead end, which
>> >> shouldn't be extended.
>> >
>> > Agreed.
>> >
>> > The panel control being bound in with the Atmel control has no hook
>> > for the EDT5x06 touch driver to hook in and keep the power to the
>> > touch controller active. When the panel disable gets called, bye bye
>> > touch overlay :-(
>> >
>> > And I'm reading the driver change as more of a hack to get it to work
>> > on your platform, not as adding support for the Waveshare panel
>> > variant.
>> > Waveshare deliberately cloned the behaviour of the Pi 7" panel in
>> > order to make it work with the old Pi firmware drivers, so it
>> > shouldn't need any significant changes. Where did the new timings come
>> > from?
>> >
>> >   Dave
>> hi Dave :
>> that's means the panel driver split into 3 sub-modules:
>> panel + panel_bridge + regulator.
> 
> Correct.
> 
> You'll have a fourth device in edt_ft5x06 for the touch overlay too,
> which will link to the regulator driver for power control.
> 
>> I have a question: in the
>> static int rpi_touchscreen_probe(struct i2c_client *i2c)
>> {
>>         ......
>>
>>         ver = rpi_touchscreen_i2c_read(ts, REG_ID);
>>         if (ver < 0) {
>>                 dev_err(dev, "Atmel I2C read failed: %d\n", ver);
>>                 return -ENODEV;
>>         }
>>
>>         switch (ver) {
>>         case 0xde: /* ver 1 */
>>         case 0xc3: /* ver 2 */
>>                 break;
>>         default:
>>                 dev_err(dev, "Unknown Atmel firmware revision: 0x%02x\n", ver);
>>                 return -ENODEV;
>>         }
>>
>>         ......
>> }
>> i think this "I2C read" can use to detect whether the panel is connected to dsi controller.
>>
>> and when split the panel driver into 3 sub-modules, it seems the default way is connected.
>> if I drop the panel , run modetest to check the connector status , result connected.
>> Is there any way to detect the connection in this case?
>> Thanks
> 
> I am not aware of any DSI drivers that support hotplugging, therefore
> the connector state will always be connected if the device probes.
> 
> On vc4 the relevant DSI host controller has to have been enabled in
> device tree and will be a required component for binding. The DSI host
> controller will be waiting on the DSI peripheral driver to call
> mipi_dsi_attach, which then calls component_add. If the panel or panel
> regulator isn't present, then that never happens if the panel isn't
> present, so vc4 won't bind.
> It is a little ugly in that you lose the whole DRM card, but that is
> how I understand DRM is generally set up to work for DSI or similar
> display interfaces.
> 
>> -------------------------------------
>>
>> Where did the new timings come from?
>>
>> -------------------------------------
>> My platform dphy tx hardware has certain limitations.
>> Only supports integer multiples of 10M bitrate:
>> such as 160M ,170M, 180M,190M,...1G(max)
>>
>> as common dphy bitrate = pixclock*bpp/lanes.
>> This value cannot match successfully in most cases.
>>
>> so in order to match bitrate , I choose a bitrate value around pixclock*bpp/lanes,
>> Prevent overflow and underflow by fine-tuning the timing parameters:-(
>> that will make the new timming value.
> 
> That isn't really a function of the panel then.
> 
> All DRM bridges have the option to define a mode_fixup in
> drm_bridge_funcs, and that gives you the option to adjust the timings
> as required.
> 
> vc4 has a similar constraint in that the PHY only has an integer
> divider from a 2 or 3GHz PLL. It implements mode_fixup to compute the
> next highest pixel clock, and then adjusts the horizontal front porch
> to keep the same line timing. See
> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/vc4/vc4_dsi.c#L825
> I see 
I never thought that mode fixup is used to do this.
This would be a correct way to modify its timming parameters

thanks you Dave
>   Dave
> 
>> >
>> >> Btw there are already DT overlays in mainline which seems to use the
>> >> Raspberry Pi 7inch panel (without touch function yet) [2].
>> >>
>> >> [1] - https://github.com/lategoodbye/rpi-zero/commits/v6.7-7inch-ts
>> >> [2] -
>> >> https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rpidsi.dtso?h=v6.6.2&id=6b4da1354fd81adace0cda448c77d8f2a47d8474
>> >>
>> >> >
>> >> > Shengyang Chen (2):
>> >> >    dt-bindings: display: panel: raspberrypi: Add compatible property for
>> >> >      waveshare 7inch touchscreen panel
>> >> >    gpu: drm: panel: raspberrypi: add new display mode and new probing
>> >> >      process
>> >> >
>> >> >   .../panel/raspberrypi,7inch-touchscreen.yaml  |  4 +-
>> >> >   .../drm/panel/panel-raspberrypi-touchscreen.c | 99 ++++++++++++++++---
>> >> >   2 files changed, 91 insertions(+), 12 deletions(-)
>> >> >
>> >>

Powered by blists - more mailing lists