lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <5eecd094-bc14-4257-bbe9-1e20aabd38f7@ti.com>
Date:   Thu, 7 Dec 2023 10:29:02 +0530
From:   "Kumar, Udit" <u-kumar1@...com>
To:     Neha Malcom Francis <n-francis@...com>, <nm@...com>,
        <vigneshr@...com>, <kristo@...nel.org>, <robh+dt@...nel.org>,
        <krzysztof.kozlowski+dt@...aro.org>, <conor+dt@...nel.org>,
        <a-nandan@...com>
CC:     <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <eblanc@...libre.com>, <jneanne@...libre.com>,
        <aseketeli@...libre.com>, <jpanis@...libre.com>, <j-luthra@...com>,
        <vaishnav.a@...com>, <hnagalla@...com>, <devarsht@...com>
Subject: Re: [PATCH v9 5/7] arm64: dts: ti: k3-am69-sk: Add support for
 TPS6594 PMIC


On 12/5/2023 3:04 PM, Neha Malcom Francis wrote:
> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
> an ESM (Error Signal Monitor) which monitors the SoC error output
> signal, and a PFSM (Pre-configurable Finite State Machine) which manages
> the operational modes of the PMIC.
>
> Signed-off-by: Neha Malcom Francis <n-francis@...com>
> Tested-by: Manorit Chawdhry <m-chawdhry@...com>
> ---
>   arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
>   1 file changed, 100 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> index 9868c7049bfb..dec27acb4e96 100644
> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
>   	};
>   };
>   
> +&wkup_pmx1 {
> +	status = "okay";
> +
> +	pmic_irq_pins_default: pmic-irq-default-pins {
> +		pinctrl-single,pins = <
> +			/* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
> +			J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
> +		>;
> +	};
> +};

Could you re check this pin mux

wkup_pmx1 is defined as reg = <0x00 0x4301c038 0x00 0x02c>;

LTM, this is above wrt given size


> +
>   &wkup_pmx2 {
>   	bootph-all;
>   	wkup_uart0_pins_default: wkup-uart0-default-pins {
> @@ -631,6 +642,95 @@ eeprom@51 {
>   		compatible = "atmel,24c512";
>   		reg = <0x51>;
>   	};
> +
> +	tps659413: pmic@48 {
> +		compatible = "ti,tps6594-q1";
> +		reg = <0x48>;
> +		system-power-controller;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_irq_pins_default>;
> +		interrupt-parent = <&wkup_gpio0>;
> +		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
> +		ti,primary-pmic;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		buck12-supply = <&vsys_3v3>;
> +		buck3-supply = <&vsys_3v3>;
> +		buck4-supply = <&vsys_3v3>;
> +		buck5-supply = <&vsys_3v3>;
> +		ldo1-supply = <&vsys_3v3>;
> +		ldo2-supply = <&vsys_3v3>;
> +		ldo3-supply = <&vsys_3v3>;
> +		ldo4-supply = <&vsys_3v3>;
> +
> +		regulators {
> +			bucka12: buck12 {
> +				regulator-name = "vdd_ddr_1v1";
> +				regulator-min-microvolt = <1100000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			bucka3: buck3 {
> +				regulator-name = "vdd_ram_0v85";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			bucka4: buck4 {
> +				regulator-name = "vdd_io_1v8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			bucka5: buck5 {
> +				regulator-name = "vdd_mcu_0v85";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldoa1: ldo1 {
> +				regulator-name = "vdd_mcuio_1v8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldoa2: ldo2 {
> +				regulator-name = "vdd_mcuio_3v3";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldoa3: ldo3 {
> +				regulator-name = "vds_dll_0v8";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldoa4: ldo4 {
> +				regulator-name = "vda_mcu_1v8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
>   };
>   
>   &wkup_gpio0 {

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ