| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20231207131818.3n7z64ve6izatlvs@unchanged>
Date: Thu, 7 Dec 2023 07:18:18 -0600
From: Nishanth Menon <nm@...com>
To: MD Danish Anwar <danishanwar@...com>
CC: Vignesh Raghavendra <vigneshr@...com>,
Conor Dooley <conor+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
<linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
Tero Kristo <kristo@...nel.org>, <srk@...com>,
<r-gunasekaran@...com>
Subject: Re: [PATCH 2/3] arm64: dts: ti: k3-am642-evm: add ICSSG1 Ethernet
support
On 13:49-20231207, MD Danish Anwar wrote:
> ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
>
> The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
> MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
> CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
> bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
> port is kept disable and ICSSG1 is enabled in single MAC mode by
> default.
>
> Signed-off-by: MD Danish Anwar <danishanwar@...com>
> ---
> arch/arm64/boot/dts/ti/k3-am642-evm.dts | 105 ++++++++++++++++++++++++
> 1 file changed, 105 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> index 8c5651d2cf5d..04d1c0602d31 100644
> --- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> @@ -34,6 +34,11 @@ aliases {
> ethernet1 = &cpsw_port2;
> };
>
> + aliases {
> + ethernet2 = &icssg1_emac0;
> + ethernet3 = &icssg1_emac1;
> + };
Why another aliases section?
> +
> memory@...00000 {
> bootph-all;
> device_type = "memory";
> @@ -229,6 +234,70 @@ transceiver2: can-phy1 {
> max-bitrate = <5000000>;
> standby-gpios = <&exp1 9 GPIO_ACTIVE_HIGH>;
> };
> +
> + icssg1_eth: icssg1-eth {
> + compatible = "ti,am642-icssg-prueth";
> + pinctrl-names = "default";
> + pinctrl-0 = <&icssg1_rgmii1_pins_default>;
> +
> + sram = <&oc_sram>;
> + ti,prus = <&pru1_0>, <&rtu1_0>, <&tx_pru1_0>, <&pru1_1>, <&rtu1_1>, <&tx_pru1_1>;
> + firmware-name = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
> + "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
> + "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
> + "ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
> + "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
> + "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf";
Umm... am65x??? is that a typo? I'd rather keep it am64x here and drop
that sr2 thing. Tomorrow there will be a custom bug on am64 and then we
will have to respin this again.
> +
> + ti,pruss-gp-mux-sel = <2>, /* MII mode */
> + <2>,
> + <2>,
> + <2>, /* MII mode */
> + <2>,
> + <2>;
> +
> + ti,mii-g-rt = <&icssg1_mii_g_rt>;
> + ti,mii-rt = <&icssg1_mii_rt>;
> + ti,iep = <&icssg1_iep0>, <&icssg1_iep1>;
> +
> + interrupt-parent = <&icssg1_intc>;
> + interrupts = <24 0 2>, <25 1 3>;
> + interrupt-names = "tx_ts0", "tx_ts1";
> +
> + dmas = <&main_pktdma 0xc200 15>, /* egress slice 0 */
> + <&main_pktdma 0xc201 15>, /* egress slice 0 */
> + <&main_pktdma 0xc202 15>, /* egress slice 0 */
> + <&main_pktdma 0xc203 15>, /* egress slice 0 */
> + <&main_pktdma 0xc204 15>, /* egress slice 1 */
> + <&main_pktdma 0xc205 15>, /* egress slice 1 */
> + <&main_pktdma 0xc206 15>, /* egress slice 1 */
> + <&main_pktdma 0xc207 15>, /* egress slice 1 */
> + <&main_pktdma 0x4200 15>, /* ingress slice 0 */
> + <&main_pktdma 0x4201 15>; /* ingress slice 1 */
> + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
> + "tx1-0", "tx1-1", "tx1-2", "tx1-3",
> + "rx0", "rx1";
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + icssg1_emac0: port@0 {
> + reg = <0>;
> + phy-handle = <&icssg1_phy1>;
> + phy-mode = "rgmii-id";
> + ti,syscon-rgmii-delay = <&main_conf 0x4110>;
> + /* Filled in by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + };
> + icssg1_emac1: port@1 {
> + reg = <1>;
> + ti,syscon-rgmii-delay = <&main_conf 0x4114>;
> + /* Filled in by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + status = "disabled";
> + };
> + };
> + };
> };
>
> &main_pmx0 {
> @@ -383,6 +452,30 @@ ddr_vtt_pins_default: ddr-vtt-default-pins {
> AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */
> >;
> };
> +
> + icssg1_mdio1_pins_default: icssg1-mdio1-default-pins {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x015c, PIN_OUTPUT, 0) /* (Y6) PRG1_MDIO0_MDC */
> + AM64X_IOPAD(0x0158, PIN_INPUT, 0) /* (AA6) PRG1_MDIO0_MDIO */
> + >;
> + };
> +
> + icssg1_rgmii1_pins_default: icssg1-rgmii1-default-pins{
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x00b8, PIN_INPUT, 2) /* (Y7) PRG1_PRU0_GPO0.PRG1_RGMII1_RD0 */
> + AM64X_IOPAD(0x00bc, PIN_INPUT, 2) /* (U8) PRG1_PRU0_GPO1.PRG1_RGMII1_RD1 */
> + AM64X_IOPAD(0x00c0, PIN_INPUT, 2) /* (W8) PRG1_PRU0_GPO2.PRG1_RGMII1_RD2 */
> + AM64X_IOPAD(0x00c4, PIN_INPUT, 2) /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
> + AM64X_IOPAD(0x00d0, PIN_INPUT, 2) /* (AA7) PRG1_PRU0_GPO6.PRG1_RGMII1_RXC */
> + AM64X_IOPAD(0x00c8, PIN_INPUT, 2) /* (Y8) PRG1_PRU0_GPO4.PRG1_RGMII1_RX_CTL */
> + AM64X_IOPAD(0x00e4, PIN_INPUT, 2) /* (AA8) PRG1_PRU0_GPO11.PRG1_RGMII1_TD0 */
> + AM64X_IOPAD(0x00e8, PIN_INPUT, 2) /* (U9) PRG1_PRU0_GPO12.PRG1_RGMII1_TD1 */
> + AM64X_IOPAD(0x00ec, PIN_INPUT, 2) /* (W9) PRG1_PRU0_GPO13.PRG1_RGMII1_TD2 */
> + AM64X_IOPAD(0x00f0, PIN_INPUT, 2) /* (AA9) PRG1_PRU0_GPO14.PRG1_RGMII1_TD3 */
> + AM64X_IOPAD(0x00f8, PIN_INPUT, 2) /* (V9) PRG1_PRU0_GPO16.PRG1_RGMII1_TXC */
> + AM64X_IOPAD(0x00f4, PIN_INPUT, 2) /* (Y9) PRG1_PRU0_GPO15.PRG1_RGMII1_TX_CTL */
> + >;
> + };
> };
>
> &main_uart0 {
> @@ -731,3 +824,15 @@ &main_mcan1 {
> pinctrl-0 = <&main_mcan1_pins_default>;
> phys = <&transceiver2>;
> };
> +
> +&icssg1_mdio {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&icssg1_mdio1_pins_default>;
> +
> + icssg1_phy1: ethernet-phy@0 {
> + reg = <0xf>;
> + tx-internal-delay-ps = <250>;
> + rx-internal-delay-ps = <2000>;
> + };
> +};
> --
> 2.34.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Powered by blists - more mailing lists