lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-Id: <20231227044347.107291-6-arinc.unal@arinc9.com> Date: Wed, 27 Dec 2023 07:43:45 +0300 From: Arınç ÜNAL <arinc.unal@...nc9.com> To: Arınç ÜNAL <arinc.unal@...nc9.com>, Daniel Golle <daniel@...rotopia.org>, Landen Chao <Landen.Chao@...iatek.com>, DENG Qingfang <dqfext@...il.com>, Sean Wang <sean.wang@...iatek.com>, Andrew Lunn <andrew@...n.ch>, Florian Fainelli <f.fainelli@...il.com>, Vladimir Oltean <olteanv@...il.com>, "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, Matthias Brugger <matthias.bgg@...il.com>, AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>, Russell King <linux@...linux.org.uk> Cc: Frank Wunderlich <frank-w@...lic-files.de>, Bartel Eerdekens <bartel.eerdekens@...stell8.be>, mithat.guner@...ont.com, erkin.bozoglu@...ont.com, netdev@...r.kernel.org, linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org, linux-mediatek@...ts.infradead.org Subject: [PATCH net-next v2 5/7] net: dsa: mt7530: improve code path for setting up port 5 There're two code paths for setting up port 5: mt7530_setup() -> mt7530_setup_port5() mt753x_phylink_mac_config() -> mt753x_mac_config() -> mt7530_mac_config() -> mt7530_setup_port5() Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5 is used as a CPU, DSA, or user port, mt7530_setup_port5() from mt753x_phylink_mac_config() won't run. That is because priv->p5_interface set on mt7530_setup_port5() will match state->interface on mt753x_phylink_mac_config() which will stop running mt7530_setup_port5() again. Therefore, mt7530_setup_port5() will never run from mt753x_phylink_mac_config(). Address this by not running mt7530_setup_port5() from mt7530_setup() if port 5 is used as a CPU, DSA, or user port. This driver isn't in the dsa_switches_apply_workarounds[] array so phylink will always be present. To keep the cases where port 5 isn't controlled by phylink working as before, preserve the mt7530_setup_port5() call from mt7530_setup(). Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when "priv" is allocated. Move setting the interface to a more specific location. It's supposed to be overwritten if PHY muxing is detected. Improve the comment which explains the process. Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com> --- drivers/net/dsa/mt7530.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index 558784f830c2..bf6c59ecc489 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -2308,16 +2308,15 @@ mt7530_setup(struct dsa_switch *ds) return ret; /* Setup port 5 */ - priv->p5_intf_sel = P5_DISABLED; - interface = PHY_INTERFACE_MODE_NA; - if (!dsa_is_unused_port(ds, 5)) { priv->p5_intf_sel = P5_INTF_SEL_GMAC5; - ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface); - if (ret && ret != -ENODEV) - return ret; } else { - /* Scan the ethernet nodes. look for GMAC1, lookup used phy */ + /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY. + * Set priv->p5_intf_sel to the appropriate value if PHY muxing + * is detected. + */ + interface = PHY_INTERFACE_MODE_NA; + for_each_child_of_node(dn, mac_np) { if (!of_device_is_compatible(mac_np, "mediatek,eth-mac")) @@ -2348,6 +2347,8 @@ mt7530_setup(struct dsa_switch *ds) of_node_put(phy_node); break; } + + mt7530_setup_port5(ds, interface); } #ifdef CONFIG_GPIOLIB @@ -2358,8 +2359,6 @@ mt7530_setup(struct dsa_switch *ds) } #endif /* CONFIG_GPIOLIB */ - mt7530_setup_port5(ds, interface); - /* Flush the FDB table */ ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL); if (ret < 0) -- 2.40.1
Powered by blists - more mailing lists