| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID:
<PAXPR04MB944832957B75F82571580E37F4662@PAXPR04MB9448.eurprd04.prod.outlook.com>
Date: Fri, 5 Jan 2024 03:20:28 +0000
From: Sandor Yu <sandor.yu@....com>
To: Alexander Stein <alexander.stein@...tq-group.com>,
"dmitry.baryshkov@...aro.org" <dmitry.baryshkov@...aro.org>,
"andrzej.hajda@...el.com" <andrzej.hajda@...el.com>,
"neil.armstrong@...aro.org" <neil.armstrong@...aro.org>, Laurent Pinchart
<laurent.pinchart@...asonboard.com>, "jonas@...boo.se" <jonas@...boo.se>,
"jernej.skrabec@...il.com" <jernej.skrabec@...il.com>, "airlied@...il.com"
<airlied@...il.com>, "daniel@...ll.ch" <daniel@...ll.ch>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"krzysztof.kozlowski+dt@...aro.org" <krzysztof.kozlowski+dt@...aro.org>,
"shawnguo@...nel.org" <shawnguo@...nel.org>, "s.hauer@...gutronix.de"
<s.hauer@...gutronix.de>, "festevam@...il.com" <festevam@...il.com>,
"vkoul@...nel.org" <vkoul@...nel.org>, "dri-devel@...ts.freedesktop.org"
<dri-devel@...ts.freedesktop.org>, "devicetree@...r.kernel.org"
<devicetree@...r.kernel.org>, "linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>, "linux-kernel@...r.kernel.org"
<linux-kernel@...r.kernel.org>, "linux-phy@...ts.infradead.org"
<linux-phy@...ts.infradead.org>
CC: "kernel@...gutronix.de" <kernel@...gutronix.de>, dl-linux-imx
<linux-imx@....com>, Oliver Brown <oliver.brown@....com>, "sam@...nborg.org"
<sam@...nborg.org>
Subject: RE: [EXT] Re: [PATCH v11 6/7] phy: freescale: Add DisplayPort PHY
driver for i.MX8MQ
Hi Alexander,
Thanks for your comments,
> -----Original Message-----
> From: Alexander Stein <alexander.stein@...tq-group.com>
>
> Hi Sandor,
>
> thanks for the patch.
>
> Am Dienstag, 17. Oktober 2023, 09:04:02 CEST schrieb Sandor Yu:
> > Add Cadence HDP-TX DisplayPort PHY driver for i.MX8MQ
> >
> > Cadence HDP-TX PHY could be put in either DP mode or HDMI mode base on
> > the configuration chosen.
> > DisplayPort PHY mode is configurated in the driver.
> >
> > Signed-off-by: Sandor Yu <Sandor.yu@....com>
> > ---
> > v9->v11:
> > *No change.
> >
> > drivers/phy/freescale/Kconfig | 10 +
> > drivers/phy/freescale/Makefile | 1 +
> > drivers/phy/freescale/phy-fsl-imx8mq-dp.c | 720
> > ++++++++++++++++++++++
> > 3 files changed, 731 insertions(+)
> > create mode 100644 drivers/phy/freescale/phy-fsl-imx8mq-dp.c
> >
> > diff --git a/drivers/phy/freescale/Kconfig
> > b/drivers/phy/freescale/Kconfig index 853958fb2c063..c39709fd700ac
> > 100644
> > --- a/drivers/phy/freescale/Kconfig
> > +++ b/drivers/phy/freescale/Kconfig
> > @@ -35,6 +35,16 @@ config PHY_FSL_IMX8M_PCIE
> > Enable this to add support for the PCIE PHY as found on
> > i.MX8M family of SOCs.
> >
> > +config PHY_FSL_IMX8MQ_DP
> > + tristate "Freescale i.MX8MQ DP PHY support"
> > + depends on OF && HAS_IOMEM
> > + depends on COMMON_CLK
> > + select GENERIC_PHY
> > + select CDNS_MHDP_HELPER
> > + help
> > + Enable this to support the Cadence HDPTX DP PHY driver
> > + on i.MX8MQ SOC.
> > +
> > endif
> >
> > config PHY_FSL_LYNX_28G
> > diff --git a/drivers/phy/freescale/Makefile
> > b/drivers/phy/freescale/Makefile index cedb328bc4d28..47e5285209fa8
> > 100644
> > --- a/drivers/phy/freescale/Makefile
> > +++ b/drivers/phy/freescale/Makefile
> > @@ -1,4 +1,5 @@
> > # SPDX-License-Identifier: GPL-2.0-only
> > +obj-$(CONFIG_PHY_FSL_IMX8MQ_DP) +=
> phy-fsl-imx8mq-dp.o
> > obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> > obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
> > obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> > diff --git a/drivers/phy/freescale/phy-fsl-imx8mq-dp.c
> > b/drivers/phy/freescale/phy-fsl-imx8mq-dp.c new file mode 100644 index
> > 0000000000000..5f0d7da16b422
> > --- /dev/null
> > +++ b/drivers/phy/freescale/phy-fsl-imx8mq-dp.c
> > @@ -0,0 +1,720 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Cadence HDP-TX Display Port Interface (DP) PHY driver
> > + *
> > + * Copyright (C) 2022, 2023 NXP Semiconductor, Inc.
> > + */
> > +#include <asm/unaligned.h>
> > +#include <drm/bridge/cdns-mhdp-helper.h> #include <linux/clk.h>
> > +#include <linux/kernel.h> #include <linux/phy/phy.h> #include
> > +<linux/platform_device.h> #include <linux/io.h> #include
> > +<linux/iopoll.h>
> > +
> > +#define ADDR_PHY_AFE 0x80000
> > +
> > +/* PHY registers */
> > +#define CMN_SSM_BIAS_TMR 0x0022
> > +#define CMN_PLLSM0_PLLEN_TMR 0x0029
> > +#define CMN_PLLSM0_PLLPRE_TMR 0x002a
> > +#define CMN_PLLSM0_PLLVREF_TMR 0x002b
> > +#define CMN_PLLSM0_PLLLOCK_TMR 0x002c
> > +#define CMN_PLLSM0_USER_DEF_CTRL 0x002f
> > +#define CMN_PSM_CLK_CTRL 0x0061
> > +#define CMN_PLL0_VCOCAL_START 0x0081
> > +#define CMN_PLL0_VCOCAL_INIT_TMR 0x0084
> > +#define CMN_PLL0_VCOCAL_ITER_TMR 0x0085
> > +#define CMN_PLL0_INTDIV 0x0094
> > +#define CMN_PLL0_FRACDIV 0x0095
> > +#define CMN_PLL0_HIGH_THR 0x0096
> > +#define CMN_PLL0_DSM_DIAG 0x0097
> > +#define CMN_PLL0_SS_CTRL2 0x0099
> > +#define CMN_ICAL_INIT_TMR 0x00c4
> > +#define CMN_ICAL_ITER_TMR 0x00c5
> > +#define CMN_RXCAL_INIT_TMR 0x00d4
> > +#define CMN_RXCAL_ITER_TMR 0x00d5
> > +#define CMN_TXPUCAL_INIT_TMR 0x00e4
> > +#define CMN_TXPUCAL_ITER_TMR 0x00e5
> > +#define CMN_TXPDCAL_INIT_TMR 0x00f4
> > +#define CMN_TXPDCAL_ITER_TMR 0x00f5
> > +#define CMN_ICAL_ADJ_INIT_TMR 0x0102
> > +#define CMN_ICAL_ADJ_ITER_TMR 0x0103
> > +#define CMN_RX_ADJ_INIT_TMR 0x0106
> > +#define CMN_RX_ADJ_ITER_TMR 0x0107
> > +#define CMN_TXPU_ADJ_INIT_TMR 0x010a
> > +#define CMN_TXPU_ADJ_ITER_TMR 0x010b
> > +#define CMN_TXPD_ADJ_INIT_TMR 0x010e
> > +#define CMN_TXPD_ADJ_ITER_TMR 0x010f
> > +#define CMN_DIAG_PLL0_FBH_OVRD 0x01c0
> > +#define CMN_DIAG_PLL0_FBL_OVRD 0x01c1
> > +#define CMN_DIAG_PLL0_OVRD 0x01c2
> > +#define CMN_DIAG_PLL0_TEST_MODE 0x01c4
> > +#define CMN_DIAG_PLL0_V2I_TUNE 0x01c5
> > +#define CMN_DIAG_PLL0_CP_TUNE 0x01c6
> > +#define CMN_DIAG_PLL0_LF_PROG 0x01c7
> > +#define CMN_DIAG_PLL0_PTATIS_TUNE1 0x01c8
> > +#define CMN_DIAG_PLL0_PTATIS_TUNE2 0x01c9
> > +#define CMN_DIAG_HSCLK_SEL 0x01e0
> > +#define CMN_DIAG_PER_CAL_ADJ 0x01ec
> > +#define CMN_DIAG_CAL_CTRL 0x01ed
> > +#define CMN_DIAG_ACYA 0x01ff
> > +#define XCVR_PSM_RCTRL 0x4001
> > +#define XCVR_PSM_CAL_TMR 0x4002
> > +#define XCVR_PSM_A0IN_TMR 0x4003
> > +#define TX_TXCC_CAL_SCLR_MULT_0 0x4047
> > +#define TX_TXCC_CPOST_MULT_00_0 0x404c
> > +#define XCVR_DIAG_PLLDRC_CTRL 0x40e0
> > +#define XCVR_DIAG_PLLDRC_CTRL 0x40e0
> > +#define XCVR_DIAG_HSCLK_SEL 0x40e1
> > +#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR 0x40f2
> > +#define TX_PSC_A0 0x4100
> > +#define TX_PSC_A1 0x4101
> > +#define TX_PSC_A2 0x4102
> > +#define TX_PSC_A3 0x4103
> > +#define TX_RCVDET_EN_TMR 0x4122
> > +#define TX_RCVDET_ST_TMR 0x4123
> > +#define TX_DIAG_BGREF_PREDRV_DELAY 0x41e7
> > +#define TX_DIAG_BGREF_PREDRV_DELAY 0x41e7
> > +#define TX_DIAG_ACYA_0 0x41ff
> > +#define TX_DIAG_ACYA_1 0x43ff
> > +#define TX_DIAG_ACYA_2 0x45ff
> > +#define TX_DIAG_ACYA_3 0x47ff
> > +#define TX_ANA_CTRL_REG_1 0x5020
> > +#define TX_ANA_CTRL_REG_2 0x5021
> > +#define TX_DIG_CTRL_REG_1 0x5023
> > +#define TX_DIG_CTRL_REG_2 0x5024
> > +#define TXDA_CYA_AUXDA_CYA 0x5025
> > +#define TX_ANA_CTRL_REG_3 0x5026
> > +#define TX_ANA_CTRL_REG_4 0x5027
> > +#define TX_ANA_CTRL_REG_5 0x5029
> > +#define RX_PSC_A0 0x8000
> > +#define RX_PSC_CAL 0x8006
> > +#define PHY_HDP_MODE_CTRL 0xc008
> > +#define PHY_HDP_CLK_CTL 0xc009
> > +#define PHY_PMA_CMN_CTRL1 0xc800
> > +
> > +/* PHY_PMA_CMN_CTRL1 */
> > +#define CMA_REF_CLK_SEL_MASK GENMASK(6, 4)
> > +#define CMA_REF_CLK_RCV_EN_MASK BIT(3)
> > +#define CMA_REF_CLK_RCV_EN 1
> > +
> > +/* PHY_HDP_CLK_CTL */
> > +#define PLL_DATA_RATE_CLK_DIV_MASK GENMASK(15, 8)
> > +#define PLL_DATA_RATE_CLK_DIV_HBR 0x24
> > +#define PLL_DATA_RATE_CLK_DIV_HBR2 0x12
> > +#define PLL_CLK_EN_ACK BIT(3)
> > +#define PLL_CLK_EN BIT(2)
> > +#define PLL_READY BIT(1)
> > +#define PLL_EN BIT(0)
> > +
> > +/* CMN_DIAG_HSCLK_SEL */
> > +#define HSCLK1_SEL_MASK GENMASK(5,
> 4)
> > +#define HSCLK0_SEL_MASK GENMASK(1,
> 0)
> > +#define HSCLK_PLL0_DIV2 1
> > +
> > +/* XCVR_DIAG_HSCLK_SEL */
> > +#define HSCLK_SEL_MODE3_MASK GENMASK(13, 12)
> > +#define HSCLK_SEL_MODE3_HSCLK1 1
> > +
> > +/* XCVR_DIAG_PLLDRC_CTRL */
> > +#define DPLL_CLK_SEL_MODE3 BIT(14)
> > +#define DPLL_DATA_RATE_DIV_MODE3_MASK
> GENMASK(13, 12)
> > +
> > +/* PHY_HDP_MODE_CTRL */
> > +#define POWER_STATE_A3_ACK BIT(7)
> > +#define POWER_STATE_A2_ACK BIT(6)
> > +#define POWER_STATE_A1_ACK BIT(5)
> > +#define POWER_STATE_A0_ACK BIT(4)
> > +#define POWER_STATE_A3 BIT(3)
> > +#define POWER_STATE_A2 BIT(2)
> > +#define POWER_STATE_A1 BIT(1)
> > +#define POWER_STATE_A0 BIT(0)
> > +
> > +#define REF_CLK_27MHZ 27000000
> > +
> > +enum dp_link_rate {
> > + RATE_1_6 = 162000,
> > + RATE_2_1 = 216000,
> > + RATE_2_4 = 243000,
> > + RATE_2_7 = 270000,
> > + RATE_3_2 = 324000,
> > + RATE_4_3 = 432000,
> > + RATE_5_4 = 540000,
> > + RATE_8_1 = 810000,
>
> RATE_8_1 is unused.
OK, will remove it.
>
> > +};
> > +
> > +#define MAX_LINK_RATE RATE_5_4
> > +
> > +struct phy_pll_reg {
> > + u16 val[7];
> > + u32 addr;
> > +};
> > +
> > +static const struct phy_pll_reg phy_pll_27m_cfg[] = {
> > + /* 1.62 2.16 2.43 2.7 3.24 4.32 5.4
> register
> > address */ + {{ 0x010e, 0x010e, 0x010e, 0x010e, 0x010e, 0x010e,
> > 0x010e
> },
> > CMN_PLL0_VCOCAL_INIT_TMR }, + {{ 0x001b, 0x001b, 0x001b, 0x001b,
> 0x001b,
> > 0x001b, 0x001b }, CMN_PLL0_VCOCAL_ITER_TMR }, + {{ 0x30b9,
> 0x3087, 0x3096,
> > 0x30b4, 0x30b9, 0x3087, 0x30b4 }, CMN_PLL0_VCOCAL_START }, + {{
> 0x0077,
> > 0x009f, 0x00b3, 0x00c7, 0x0077, 0x009f, 0x00c7 }, CMN_PLL0_INTDIV }, +
> {{
> > 0xf9da, 0xf7cd, 0xf6c7, 0xf5c1, 0xf9da, 0xf7cd, 0xf5c1 },
> > CMN_PLL0_FRACDIV }, + {{ 0x001e, 0x0028, 0x002d, 0x0032, 0x001e,
> 0x0028, 0x0032 },
> > CMN_PLL0_HIGH_THR }, + {{ 0x0020, 0x0020, 0x0020, 0x0020,
> 0x0020,
> 0x0020,
> > 0x0020 }, CMN_PLL0_DSM_DIAG }, + {{ 0x0000, 0x1000, 0x1000,
> 0x1000,
> 0x0000,
> > 0x1000, 0x1000 }, CMN_PLLSM0_USER_DEF_CTRL }, + {{ 0x0000,
> 0x0000, 0x0000,
> > 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_OVRD }, +
> {{ 0x0000,
> > 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 },
> > CMN_DIAG_PLL0_FBH_OVRD },
> > + {{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 },
> > CMN_DIAG_PLL0_FBL_OVRD }, + {{ 0x0006, 0x0007, 0x0007, 0x0007,
> 0x0006,
> > 0x0007, 0x0007 }, CMN_DIAG_PLL0_V2I_TUNE }, + {{ 0x0043, 0x0043,
> > 0x0043, 0x0042, 0x0043, 0x0043, 0x0042 }, CMN_DIAG_PLL0_CP_TUNE }, +
> > {{
> 0x0008,
> > 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008 },
> > CMN_DIAG_PLL0_LF_PROG },
> > + {{ 0x0100, 0x0001, 0x0001, 0x0001, 0x0100, 0x0001, 0x0001 },
> > CMN_DIAG_PLL0_PTATIS_TUNE1 }, + {{ 0x0007, 0x0001, 0x0001,
> 0x0001,
> 0x0007,
> > 0x0001, 0x0001 }, CMN_DIAG_PLL0_PTATIS_TUNE2 }, + {{ 0x0020,
> 0x0020,
> > 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 }, CMN_DIAG_PLL0_TEST_MODE},
> +
> > {{ 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016 },
> > CMN_PSM_CLK_CTRL } +};
> > +
> > +struct cdns_hdptx_dp_phy {
> > + struct cdns_mhdp_base base;
> > +
> > + void __iomem *regs; /* DPTX registers base */
> > + struct device *dev;
> > + struct phy *phy;
> > + struct mutex mbox_mutex; /* mutex to protect mailbox */
> > + struct clk *ref_clk, *apb_clk;
> > + u32 ref_clk_rate;
> > + u32 num_lanes;
> > + u32 link_rate;
> > + bool power_up;
> > +};
> > +
> > +static int cdns_phy_reg_write(struct cdns_hdptx_dp_phy *cdns_phy, u32
> > +addr,
> > u32 val) +{
> > + return cdns_mhdp_reg_write(&cdns_phy->base, ADDR_PHY_AFE +
> (addr
> > + <<
> 2),
> > val); +}
> > +
> > +static u32 cdns_phy_reg_read(struct cdns_hdptx_dp_phy *cdns_phy, u32
> > +addr) {
> > + u32 reg32;
> > +
> > + cdns_mhdp_reg_read(&cdns_phy->base, ADDR_PHY_AFE + (addr <<
> 2),
> ®32);
> > + return reg32;
> > +}
> > +
> > +static int link_rate_index(u32 rate)
> > +{
> > + switch (rate) {
> > + case RATE_1_6:
> > + return 0;
> > + case RATE_2_1:
> > + return 1;
> > + case RATE_2_4:
> > + return 2;
> > + case RATE_2_7:
> > + return 3;
> > + case RATE_3_2:
> > + return 4;
> > + case RATE_4_3:
> > + return 5;
> > + case RATE_5_4:
> > + return 6;
> > + default:
> > + return -1;
> > + }
> > +}
> > +
> > +static int hdptx_dp_clk_enable(struct cdns_hdptx_dp_phy *cdns_phy) {
> > + struct device *dev = cdns_phy->dev;
> > + u32 ref_clk_rate;
> > + int ret;
> > +
> > + cdns_phy->ref_clk = devm_clk_get(dev, "ref");
> > + if (IS_ERR(cdns_phy->ref_clk)) {
> > + dev_err(dev, "phy ref clock not found\n");
> > + return PTR_ERR(cdns_phy->ref_clk);
> > + }
> > +
> > + cdns_phy->apb_clk = devm_clk_get(dev, "apb");
> > + if (IS_ERR(cdns_phy->apb_clk)) {
> > + dev_err(dev, "phy apb clock not found\n");
> > + return PTR_ERR(cdns_phy->apb_clk);
> > + }
> > +
> > + ret = clk_prepare_enable(cdns_phy->ref_clk);
> > + if (ret) {
> > + dev_err(cdns_phy->dev, "Failed to prepare ref clock\n");
> > + return ret;
> > + }
> > +
> > + ref_clk_rate = clk_get_rate(cdns_phy->ref_clk);
> > + if (!ref_clk_rate) {
> > + dev_err(cdns_phy->dev, "Failed to get ref clock rate\n");
> > + goto err_ref_clk;
> > + }
> > +
> > + if (ref_clk_rate == REF_CLK_27MHZ) {
> > + cdns_phy->ref_clk_rate = ref_clk_rate;
> > + } else {
> > + dev_err(cdns_phy->dev, "Not support Ref Clock Rate(%dHz)
> \n",
> > ref_clk_rate); + goto err_ref_clk;
> > + }
> > +
> > + ret = clk_prepare_enable(cdns_phy->apb_clk);
> > + if (ret) {
> > + dev_err(cdns_phy->dev, "Failed to prepare apb clock\n");
> > + goto err_ref_clk;
> > + }
> > +
> > + return 0;
> > +
> > +err_ref_clk:
> > + clk_disable_unprepare(cdns_phy->ref_clk);
> > + return -EINVAL;
> > +}
> > +
> > +static void hdptx_dp_clk_disable(struct cdns_hdptx_dp_phy *cdns_phy)
> > +{
> > + clk_disable_unprepare(cdns_phy->ref_clk);
> > + clk_disable_unprepare(cdns_phy->apb_clk);
> > +}
> > +
> > +static void hdptx_dp_aux_cfg(struct cdns_hdptx_dp_phy *cdns_phy) {
> > + /* Power up Aux */
> > + cdns_phy_reg_write(cdns_phy, TXDA_CYA_AUXDA_CYA, 1);
> > +
> > + cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_1, 0x3);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_2, 36);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0100);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0300);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_3, 0x0000);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2008);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2018);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xa018);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030c);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_5, 0x0000);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_4, 0x1001);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xa098);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xa198);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030d);
> > + ndelay(150);
> > + cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030f); }
> > +
> > +/* PMA common configuration for 27MHz */ static void
> > +hdptx_dp_phy_pma_cmn_cfg_27mhz(struct cdns_hdptx_dp_phy
> > *cdns_phy) +{
> > + u32 num_lanes = cdns_phy->num_lanes;
> > + u16 val;
> > + int k;
> > +
> > + /* Enable PMA input ref clk(CMN_REF_CLK_RCV_EN) */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> > + val &= ~CMA_REF_CLK_RCV_EN_MASK;
> > + val |= FIELD_PREP(CMA_REF_CLK_RCV_EN_MASK,
> CMA_REF_CLK_RCV_EN);
> > + cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
> > +
> > + /* Startup state machine registers */
> > + cdns_phy_reg_write(cdns_phy, CMN_SSM_BIAS_TMR, 0x0087);
> > + cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLEN_TMR, 0x001b);
> > + cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLPRE_TMR, 0x0036);
> > + cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLVREF_TMR,
> 0x001b);
> > + cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLLOCK_TMR,
> 0x006c);
> > +
> > + /* Current calibration registers */
> > + cdns_phy_reg_write(cdns_phy, CMN_ICAL_INIT_TMR, 0x0044);
> > + cdns_phy_reg_write(cdns_phy, CMN_ICAL_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_ITER_TMR, 0x0006);
> > +
> > + /* Resistor calibration registers */
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_RXCAL_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_RXCAL_ITER_TMR, 0x0006);
> > + cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_INIT_TMR, 0x0022);
> > + cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_ITER_TMR, 0x0006);
> > +
> > + for (k = 0; k < num_lanes; k = k + 1) {
> > + /* Power state machine registers */
> > + cdns_phy_reg_write(cdns_phy, XCVR_PSM_CAL_TMR | (k
> <<
> > + 9),
> 0x016d);
> > + cdns_phy_reg_write(cdns_phy, XCVR_PSM_A0IN_TMR | (k
> <<
> > + 9),
> 0x016d);
> > + /* Transceiver control and diagnostic registers */
> > + cdns_phy_reg_write(cdns_phy,
> > + XCVR_DIAG_LANE_FCM_EN_MGN_TMR
> | (k << 9),
> > 0x00a2); + cdns_phy_reg_write(cdns_phy,
> TX_DIAG_BGREF_PREDRV_DELAY | (k <<
> > 9), 0x0097); + /* Transmitter receiver detect registers */
> > + cdns_phy_reg_write(cdns_phy, TX_RCVDET_EN_TMR | (k <<
> > + 9),
> 0x0a8c);
> > + cdns_phy_reg_write(cdns_phy, TX_RCVDET_ST_TMR | (k <<
> > + 9),
> 0x0036);
> > + }
> > +
> > + cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_0, 1);
> > + cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_1, 1);
> > + cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_2, 1);
> > + cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_3, 1); }
> > +
> > +static void hdptx_dp_phy_pma_cmn_pll0_27mhz(struct
> cdns_hdptx_dp_phy
> > *cdns_phy) +{
> > + u32 num_lanes = cdns_phy->num_lanes;
> > + u32 link_rate = cdns_phy->link_rate;
> > + u16 val;
> > + int index, i, k;
> > +
> > + /* DP PLL data rate 0/1 clock divider value */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > + val &= ~PLL_DATA_RATE_CLK_DIV_MASK;
> > + if (link_rate <= RATE_2_7)
> > + val |= FIELD_PREP(PLL_DATA_RATE_CLK_DIV_MASK,
> > + PLL_DATA_RATE_CLK_DIV_HBR);
> > + else
> > + val |= FIELD_PREP(PLL_DATA_RATE_CLK_DIV_MASK,
> > + PLL_DATA_RATE_CLK_DIV_HBR2);
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +
> > + /* High speed clock 0/1 div */
> > + val = cdns_phy_reg_read(cdns_phy, CMN_DIAG_HSCLK_SEL);
> > + val &= ~(HSCLK1_SEL_MASK | HSCLK0_SEL_MASK);
> > + if (link_rate <= RATE_2_7) {
> > + val |= FIELD_PREP(HSCLK1_SEL_MASK, HSCLK_PLL0_DIV2);
> > + val |= FIELD_PREP(HSCLK0_SEL_MASK, HSCLK_PLL0_DIV2);
> > + }
> > + cdns_phy_reg_write(cdns_phy, CMN_DIAG_HSCLK_SEL, val);
> > +
> > + for (k = 0; k < num_lanes; k++) {
> > + val = cdns_phy_reg_read(cdns_phy, (XCVR_DIAG_HSCLK_SEL
> |
> (k << 9)));
> > + val &= ~HSCLK_SEL_MODE3_MASK;
> > + if (link_rate <= RATE_2_7)
> > + val |= FIELD_PREP(HSCLK_SEL_MODE3_MASK,
> HSCLK_SEL_MODE3_HSCLK1);
> > + cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_HSCLK_SEL | (k
> > + <<
> 9)), val);
> > + }
> > +
> > + /* DP PHY PLL 27MHz configuration */
> > + index = link_rate_index(link_rate);
> > + for (i = 0; i < ARRAY_SIZE(phy_pll_27m_cfg); i++)
> > + cdns_phy_reg_write(cdns_phy, phy_pll_27m_cfg[i].addr,
> > + phy_pll_27m_cfg[i].val[index]);
> > +
> > + /* Transceiver control and diagnostic registers */
> > + for (k = 0; k < num_lanes; k++) {
> > + val = cdns_phy_reg_read(cdns_phy,
> (XCVR_DIAG_PLLDRC_CTRL
> > + |
> (k << 9)));
> > + val &= ~(DPLL_DATA_RATE_DIV_MODE3_MASK |
> DPLL_CLK_SEL_MODE3);
> > + if (link_rate <= RATE_2_7)
> > + val |=
> FIELD_PREP(DPLL_DATA_RATE_DIV_MODE3_MASK,
> 2);
> > + else
> > + val |=
> FIELD_PREP(DPLL_DATA_RATE_DIV_MODE3_MASK,
> 1);
> > + cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_PLLDRC_CTRL |
> (k
> << 9)), val);
> > + }
> > +
> > + for (k = 0; k < num_lanes; k = k + 1) {
> > + /* Power state machine registers */
> > + cdns_phy_reg_write(cdns_phy, (XCVR_PSM_RCTRL | (k <<
> > + 9)),
> 0xbefc);
> > + cdns_phy_reg_write(cdns_phy, (TX_PSC_A0 | (k << 9)),
> 0x6799);
> > + cdns_phy_reg_write(cdns_phy, (TX_PSC_A1 | (k << 9)),
> 0x6798);
> > + cdns_phy_reg_write(cdns_phy, (TX_PSC_A2 | (k << 9)),
> 0x0098);
> > + cdns_phy_reg_write(cdns_phy, (TX_PSC_A3 | (k << 9)),
> 0x0098);
> > + /* Receiver calibration power state definition register */
> > + val = cdns_phy_reg_read(cdns_phy, RX_PSC_CAL | (k << 9));
> > + val &= 0xffbb;
> > + cdns_phy_reg_write(cdns_phy, (RX_PSC_CAL | (k << 9)),
> val);
> > + val = cdns_phy_reg_read(cdns_phy, RX_PSC_A0 | (k << 9));
> > + val &= 0xffbb;
> > + cdns_phy_reg_write(cdns_phy, (RX_PSC_A0 | (k << 9)), val);
> > + }
> > +}
> > +
> > +static void hdptx_dp_phy_ref_clock_type(struct cdns_hdptx_dp_phy
> > +*cdns_phy) {
> > + u32 val;
> > +
> > + val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> > + val &= ~CMA_REF_CLK_SEL_MASK;
> > + /*
> > + * single ended reference clock (val |= 0x0030);
> > + * differential clock (val |= 0x0000);
> > + *
> > + * for differential clock on the refclk_p and
> > + * refclk_m off chip pins: CMN_DIAG_ACYA[8]=1'b1
> > + * cdns_phy_reg_write(cdns_phy, CMN_DIAG_ACYA, 0x0100);
> > + */
> > + val |= FIELD_PREP(CMA_REF_CLK_SEL_MASK, 3);
> > + cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val); }
> > +
> > +static int wait_for_ack(struct cdns_hdptx_dp_phy *cdns_phy, u32 reg,
> > +u32
> > mask, + const char *err_msg)
> > +{
> > + u32 val, i;
> > +
> > + for (i = 0; i < 10; i++) {
> > + val = cdns_phy_reg_read(cdns_phy, reg);
> > + if (val & mask)
> > + return 0;
> > + msleep(20);
> > + }
> > +
> > + dev_err(cdns_phy->dev, "%s\n", err_msg);
> > + return -1;
>
> return -ETIMEDOUT?
OK.
>
> > +}
> > +
> > +static int wait_for_ack_clear(struct cdns_hdptx_dp_phy *cdns_phy, u32
> > +reg,
> > u32 mask, + const char *err_msg)
> > +{
> > + u32 val, i;
> > +
> > + for (i = 0; i < 10; i++) {
> > + val = cdns_phy_reg_read(cdns_phy, reg);
> > + if (!(val & mask))
> > + return 0;
> > + msleep(20);
> > + }
> > +
> > + dev_err(cdns_phy->dev, "%s\n", err_msg);
> > + return -1;
>
> return -ETIMEDOUT?
OK.
>
> > +}
> > +
> > +static int hdptx_dp_phy_power_up(struct cdns_hdptx_dp_phy *cdns_phy)
> > +{
> > + u32 val;
> > +
> > + /* Enable HDP PLL’s for high speed clocks */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > + val |= PLL_EN;
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > + if (wait_for_ack(cdns_phy, PHY_HDP_CLK_CTL, PLL_READY,
> > + "Wait PLL Ack failed"))
> > + return -1;
> > +
> > + /* Enable HDP PLL’s data rate and full rate clocks out of PMA. */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > + val |= PLL_CLK_EN;
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > + if (wait_for_ack(cdns_phy, PHY_HDP_CLK_CTL, PLL_CLK_EN_ACK,
> > + "Wait PLL clock enable ACK failed"))
> > + return -1;
> > +
> > + /* Configure PHY in A2 Mode */
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A2);
> > + if (wait_for_ack(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A2_ACK,
> > + "Wait A2 Ack failed"))
> > + return -1;
> > +
> > + /* Configure PHY in A0 mode (PHY must be in the A0 power
> > + * state in order to transmit data)
> > + */
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A0);
> > + if (wait_for_ack(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A0_ACK,
> > + "Wait A0 Ack failed"))
> > + return -1;
>
> Maybe you should just return the return value of wait_for_ack() in each error
> case.
OK.
>
> > + cdns_phy->power_up = true;
> > +
> > + return 0;
> > +}
> > +
> > +static void hdptx_dp_phy_power_down(struct cdns_hdptx_dp_phy
> > +*cdns_phy) {
> > + u16 val;
> > +
> > + if (!cdns_phy->power_up)
> > + return;
> > +
> > + /* Place the PHY lanes in the A3 power state. */
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A3);
> > + if (wait_for_ack(cdns_phy, PHY_HDP_MODE_CTRL,
> POWER_STATE_A3_ACK,
> > + "Wait A3 Ack failed"))
> > + return;
> > +
> > + /* Disable HDP PLL’s data rate and full rate clocks out of PMA. */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > + val &= ~PLL_CLK_EN;
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > + if (wait_for_ack_clear(cdns_phy, PHY_HDP_CLK_CTL,
> PLL_CLK_EN_ACK,
> > + "Wait PLL clock Ack clear failed"))
> > + return;
> > +
> > + /* Disable HDP PLL’s for high speed clocks */
> > + val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > + val &= ~PLL_EN;
> > + cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > + if (wait_for_ack_clear(cdns_phy, PHY_HDP_CLK_CTL, PLL_READY,
> > + "Wait PLL Ack clear failed"))
> > + return;
>
> I would have expected cdns_phy->power_up = false somewhere in this
> function.
>
I will added it.
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_on(struct phy *phy) {
> > + struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +
> > + return hdptx_dp_phy_power_up(cdns_phy); }
> > +
> > +static int cdns_hdptx_dp_phy_off(struct phy *phy) {
> > + struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +
> > + hdptx_dp_phy_power_down(cdns_phy);
> > +
> > + return 0;
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_init(struct phy *phy) {
> > + struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + hdptx_dp_phy_ref_clock_type(cdns_phy);
> > +
> > + /* PHY power up */
> > + ret = hdptx_dp_phy_power_up(cdns_phy);
> > + if (ret < 0)
> > + return ret;
> > +
> > + hdptx_dp_aux_cfg(cdns_phy);
> > +
> > + return ret;
> > +}
> > +
> > +static int cdns_hdptx_dp_configure(struct phy *phy,
> > + union phy_configure_opts *opts) {
> > + struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + cdns_phy->link_rate = opts->dp.link_rate;
> > + cdns_phy->num_lanes = opts->dp.lanes;
> > +
> > + if (cdns_phy->link_rate > MAX_LINK_RATE) {
> > + dev_err(cdns_phy->dev, "Link Rate(%d) Not supported\n",
> > cdns_phy->link_rate); + return false;
> > + }
> > +
> > + /* Disable phy clock if PHY in power up state */
> > + hdptx_dp_phy_power_down(cdns_phy);
> > +
> > + if (cdns_phy->ref_clk_rate == REF_CLK_27MHZ) {
> > + hdptx_dp_phy_pma_cmn_cfg_27mhz(cdns_phy);
> > + hdptx_dp_phy_pma_cmn_pll0_27mhz(cdns_phy);
> > + } else {
> > + dev_err(cdns_phy->dev, "Not support ref clock rate\n");
> > + }
> > +
> > + /* PHY power up */
> > + ret = hdptx_dp_phy_power_up(cdns_phy);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct phy_ops cdns_hdptx_dp_phy_ops = {
> > + .init = cdns_hdptx_dp_phy_init,
> > + .configure = cdns_hdptx_dp_configure,
> > + .power_on = cdns_hdptx_dp_phy_on,
> > + .power_off = cdns_hdptx_dp_phy_off,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static int cdns_hdptx_dp_phy_probe(struct platform_device *pdev) {
> > + struct cdns_hdptx_dp_phy *cdns_phy;
> > + struct device *dev = &pdev->dev;
> > + struct device_node *node = dev->of_node;
> > + struct phy_provider *phy_provider;
> > + struct resource *res;
> > + struct phy *phy;
> > + int ret;
> > +
> > + cdns_phy = devm_kzalloc(dev, sizeof(*cdns_phy), GFP_KERNEL);
> > + if (!cdns_phy)
> > + return -ENOMEM;
> > +
> > + dev_set_drvdata(dev, cdns_phy);
> > + cdns_phy->dev = dev;
> > + mutex_init(&cdns_phy->mbox_mutex);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res)
> > + return -ENODEV;
> > + cdns_phy->regs = devm_ioremap(dev, res->start, resource_size(res));
> > + if (IS_ERR(cdns_phy->regs))
> > + return PTR_ERR(cdns_phy->regs);
> > +
> > + phy = devm_phy_create(dev, node, &cdns_hdptx_dp_phy_ops);
> > + if (IS_ERR(phy))
> > + return PTR_ERR(phy);
> > +
> > + phy->attrs.mode = PHY_MODE_DP;
> > + cdns_phy->phy = phy;
> > + phy_set_drvdata(phy, cdns_phy);
> > +
> > + /* init base struct for access mhdp mailbox */
> > + cdns_phy->base.dev = cdns_phy->dev;
> > + cdns_phy->base.regs = cdns_phy->regs;
> > + cdns_phy->base.mbox_mutex = &cdns_phy->mbox_mutex;
>
> How is this mutex supposed to work? From the name
> cdns_phy->base.mbox_mutex is supposed to protect the mailbox access in the
> cdns-mhdp base, right?
> But this mutex is different, initialized separately and thus is independent from
> mhdp->mbox_mutex in cdns-mhdp8501-core.c.
Yes, this mutex use to protect mailbox access in PHY driver only.
In cdns-mhdp8501-core.c driver, every access PHY API functions are protected by core driver's mbox_mutex.
Best regards,
Sandor
>
> Best regards,
> Alexander
>
> > +
> > + ret = hdptx_dp_clk_enable(cdns_phy);
> > + if (ret) {
> > + dev_err(dev, "Init clk fail\n");
> > + return -EINVAL;
> > + }
> > +
> > + phy_provider = devm_of_phy_provider_register(dev,
> of_phy_simple_xlate);
> > + if (IS_ERR(phy_provider)) {
> > + ret = PTR_ERR(phy_provider);
> > + goto clk_disable;
> > + }
> > +
> > + return 0;
> > +
> > +clk_disable:
> > + hdptx_dp_clk_disable(cdns_phy);
> > +
> > + return -EINVAL;
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_remove(struct platform_device *pdev) {
> > + struct cdns_hdptx_dp_phy *cdns_phy = platform_get_drvdata(pdev);
> > +
> > + hdptx_dp_clk_disable(cdns_phy);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id cdns_hdptx_dp_phy_of_match[] = {
> > + {.compatible = "fsl,imx8mq-dp-phy" },
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, cdns_hdptx_dp_phy_of_match);
> > +
> > +static struct platform_driver cdns_hdptx_dp_phy_driver = {
> > + .probe = cdns_hdptx_dp_phy_probe,
> > + .remove = cdns_hdptx_dp_phy_remove,
> > + .driver = {
> > + .name = "cdns-hdptx-dp-phy",
> > + .of_match_table = cdns_hdptx_dp_phy_of_match,
> > + }
> > +};
> > +module_platform_driver(cdns_hdptx_dp_phy_driver);
> > +
> > +MODULE_AUTHOR("Sandor Yu <sandor.yu@....com>");
> > +MODULE_DESCRIPTION("Cadence HDP-TX DisplayPort PHY driver");
> > +MODULE_LICENSE("GPL");
>
>
> --
> TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
> Amtsgericht München, HRB 105018
> Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
> http://www.tq-/
> group.com%2F&data=05%7C01%7CSandor.yu%40nxp.com%7C8c4206b83ee9
> 49f73f2108dbcf1072ea%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0
> %7C638331441796833531%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLj
> AwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7
> C%7C&sdata=qsc2K6yrBVT1BbBxT2RyydD%2BrmGKCTJO%2FqgAOrUMUME%3
> D&reserved=0
>
Powered by blists - more mailing lists