lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240105141153.19249-7-l.sanfilippo@kunbus.com>
Date: Fri,  5 Jan 2024 15:11:52 +0100
From: Lino Sanfilippo <l.sanfilippo@...bus.com>
To: gregkh@...uxfoundation.org,
	jirislaby@...nel.org,
	ilpo.jarvinen@...ux.intel.com
Cc: u.kleine-koenig@...gutronix.de,
	shawnguo@...nel.org,
	s.hauer@...gutronix.de,
	mcoquelin.stm32@...il.com,
	alexandre.torgue@...s.st.com,
	cniedermaier@...electronics.com,
	hugo@...ovil.com,
	m.brock@...mierlo.com,
	linux-kernel@...r.kernel.org,
	linux-serial@...r.kernel.org,
	LinoSanfilippo@....de,
	lukas@...ner.de,
	p.rosenberger@...bus.com,
	Lino Sanfilippo <l.sanfilippo@...bus.com>,
	stable@...r.kernel.org
Subject: [PATCH v8 6/7] serial: omap: do not override settings for RS485 support

The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.

Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before the check for the RTS GPIO.

Also relocate the assignment of serial_omap_config_rs485() to have the
complete RS485 setup in one function.

Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: stable@...r.kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@...bus.com>
---
 drivers/tty/serial/omap-serial.c | 27 ++++++++++++++-------------
 1 file changed, 14 insertions(+), 13 deletions(-)

diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index ad4c1c5d0a7f..f4c6ff806465 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1483,6 +1483,13 @@ static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
 	return omap_up_info;
 }
 
+static const struct serial_rs485 serial_omap_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
+		 SER_RS485_RX_DURING_TX,
+	.delay_rts_before_send = 1,
+	.delay_rts_after_send = 1,
+};
+
 static int serial_omap_probe_rs485(struct uart_omap_port *up,
 				   struct device *dev)
 {
@@ -1497,6 +1504,9 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
 	if (!np)
 		return 0;
 
+	up->port.rs485_config = serial_omap_config_rs485;
+	up->port.rs485_supported = serial_omap_rs485_supported;
+
 	ret = uart_get_rs485_mode(&up->port);
 	if (ret)
 		return ret;
@@ -1531,13 +1541,6 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
 	return 0;
 }
 
-static const struct serial_rs485 serial_omap_rs485_supported = {
-	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
-		 SER_RS485_RX_DURING_TX,
-	.delay_rts_before_send = 1,
-	.delay_rts_after_send = 1,
-};
-
 static int serial_omap_probe(struct platform_device *pdev)
 {
 	struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
@@ -1604,17 +1607,11 @@ static int serial_omap_probe(struct platform_device *pdev)
 		dev_info(up->port.dev, "no wakeirq for uart%d\n",
 			 up->port.line);
 
-	ret = serial_omap_probe_rs485(up, &pdev->dev);
-	if (ret < 0)
-		goto err_rs485;
-
 	sprintf(up->name, "OMAP UART%d", up->port.line);
 	up->port.mapbase = mem->start;
 	up->port.membase = base;
 	up->port.flags = omap_up_info->flags;
 	up->port.uartclk = omap_up_info->uartclk;
-	up->port.rs485_config = serial_omap_config_rs485;
-	up->port.rs485_supported = serial_omap_rs485_supported;
 	if (!up->port.uartclk) {
 		up->port.uartclk = DEFAULT_CLK_SPEED;
 		dev_warn(&pdev->dev,
@@ -1622,6 +1619,10 @@ static int serial_omap_probe(struct platform_device *pdev)
 			 DEFAULT_CLK_SPEED);
 	}
 
+	ret = serial_omap_probe_rs485(up, &pdev->dev);
+	if (ret < 0)
+		goto err_rs485;
+
 	up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	up->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	cpu_latency_qos_add_request(&up->pm_qos_request, up->latency);
-- 
2.43.0

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ