| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240125100619.154873-1-rengarajan.s@microchip.com>
Date: Thu, 25 Jan 2024 15:36:19 +0530
From: Rengarajan S <rengarajan.s@...rochip.com>
To: <kumaravel.thiagarajan@...rochip.com>,
<tharunkumar.pasumarthi@...rochip.com>, <gregkh@...uxfoundation.org>,
<jirislaby@...nel.org>, <ilpo.jarvinen@...ux.intel.com>,
<andriy.shevchenko@...ux.intel.com>, <f.fainelli@...il.com>,
<john.ogness@...utronix.de>, <tony@...mide.com>, <tglx@...utronix.de>,
<jiaqing.zhao@...ux.intel.com>, <linux-serial@...r.kernel.org>,
<linux-kernel@...r.kernel.org>
CC: <UNGLinuxDriver@...rochip.com>
Subject: [PATCH v1 tty] 8250: microchip: Add 4 Mbps support in PCI1XXXX UART
The current clock input is set to 62.5 MHz for supporting fractional
divider, which enables generation of an acceptable baud rate from any
frequency. With the current clock input the baud rate range is limited
to 3.9 Mbps. Hence, the current range is extended to support 4 Mbps
with Burst mode operation. Divisor calculation for a given baud rate is
updated as the sampling rate is reduced from 16 to 8 for 4 Mbps.
Signed-off-by: Rengarajan S <rengarajan.s@...rochip.com>
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 34 +++++++++++++++++++++----
drivers/tty/serial/8250/8250_port.c | 7 +++++
2 files changed, 36 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index d53605bf908d..6cfeba058dba 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -82,7 +82,8 @@
#define ADCL_CFG_PIN_SEL BIT(1)
#define ADCL_CFG_EN BIT(0)
-#define UART_BIT_SAMPLE_CNT 16
+#define UART_BIT_SAMPLE_CNT_8 8
+#define UART_BIT_SAMPLE_CNT_16 16
#define BAUD_CLOCK_DIV_INT_MSK GENMASK(31, 8)
#define ADCL_CFG_RTS_DELAY_MASK GENMASK(11, 8)
#define UART_CLOCK_DEFAULT (62500 * HZ_PER_KHZ)
@@ -96,6 +97,7 @@
(UART_WAKE_N_PIN | UART_WAKE_NCTS | UART_WAKE_INT)
#define UART_BAUD_CLK_DIVISOR_REG 0x54
+#define FRAC_DIV_CFG_REG 0x58
#define UART_RESET_REG 0x94
#define UART_RESET_D3_RESET_DISABLE BIT(16)
@@ -104,6 +106,10 @@
#define UART_TX_BURST_FIFO 0xA0
#define UART_RX_BURST_FIFO 0xA4
+#define UART_BIT_DIVISOR_8 0x26731000
+#define UART_BIT_DIVISOR_16 0x6ef71000
+#define UART_BAUD_4MBPS 4000000
+
#define MAX_PORTS 4
#define PORT_OFFSET 0x100
#define RX_BUF_SIZE 512
@@ -210,15 +216,24 @@ static int pci1xxxx_get_num_ports(struct pci_dev *dev)
static unsigned int pci1xxxx_get_divisor(struct uart_port *port,
unsigned int baud, unsigned int *frac)
{
+ unsigned int uart_sample_cnt;
unsigned int quot;
+ if (baud >= UART_BAUD_4MBPS) {
+ uart_sample_cnt = UART_BIT_SAMPLE_CNT_8;
+ writel(UART_BIT_DIVISOR_8, (port->membase + FRAC_DIV_CFG_REG));
+ } else {
+ uart_sample_cnt = UART_BIT_SAMPLE_CNT_16;
+ writel(UART_BIT_DIVISOR_16, (port->membase + FRAC_DIV_CFG_REG));
+ }
+
/*
* Calculate baud rate sampling period in nanoseconds.
* Fractional part x denotes x/255 parts of a nanosecond.
*/
- quot = NSEC_PER_SEC / (baud * UART_BIT_SAMPLE_CNT);
- *frac = (NSEC_PER_SEC - quot * baud * UART_BIT_SAMPLE_CNT) *
- 255 / UART_BIT_SAMPLE_CNT / baud;
+ quot = NSEC_PER_SEC / (baud * uart_sample_cnt);
+ *frac = (NSEC_PER_SEC - quot * baud * uart_sample_cnt) *
+ 255 / uart_sample_cnt / baud;
return quot;
}
@@ -237,7 +252,16 @@ static int pci1xxxx_rs485_config(struct uart_port *port,
u32 delay_in_baud_periods;
u32 baud_period_in_ns;
u32 mode_cfg = 0;
+ u32 sample_cnt;
u32 clock_div;
+ u32 frac_div;
+
+ frac_div = readl(port->membase + FRAC_DIV_CFG_REG);
+
+ if (frac_div == UART_BIT_DIVISOR_16)
+ sample_cnt = UART_BIT_SAMPLE_CNT_16;
+ else
+ sample_cnt = UART_BIT_SAMPLE_CNT_8;
/*
* pci1xxxx's uart hardware supports only RTS delay after
@@ -253,7 +277,7 @@ static int pci1xxxx_rs485_config(struct uart_port *port,
clock_div = readl(port->membase + UART_BAUD_CLK_DIVISOR_REG);
baud_period_in_ns =
FIELD_GET(BAUD_CLOCK_DIV_INT_MSK, clock_div) *
- UART_BIT_SAMPLE_CNT;
+ sample_cnt;
delay_in_baud_periods =
rs485->delay_rts_after_send * NSEC_PER_MSEC /
baud_period_in_ns;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 925ee1d61afb..2a85bc9475f9 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -2688,6 +2688,7 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
struct ktermios *termios,
const struct ktermios *old)
{
+ struct uart_8250_port *up = up_to_u8250p(port);
unsigned int tolerance = port->uartclk / 100;
unsigned int min;
unsigned int max;
@@ -2705,6 +2706,12 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
max = (port->uartclk + tolerance) / 16;
}
+ /*
+ * Microchip PCI1XXXX UART supports maximum baud rate up to 4 Mbps
+ */
+ if (up->port.type == PORT_MCHP16550A)
+ max = 4000000;
+
/*
* Ask the core to calculate the divisor for us.
* Allow 1% tolerance at the upper limit so uart clks marginally
--
2.25.1
Powered by blists - more mailing lists