lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date: Fri, 02 Feb 2024 12:19:11 +0300
From: Arınç ÜNAL via B4 Relay
 <devnull+arinc.unal.arinc9.com@...nel.org>
To: Daniel Golle <daniel@...rotopia.org>, DENG Qingfang <dqfext@...il.com>, 
 Sean Wang <sean.wang@...iatek.com>, Andrew Lunn <andrew@...n.ch>, 
 Florian Fainelli <f.fainelli@...il.com>, 
 Vladimir Oltean <olteanv@...il.com>, 
 "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, 
 Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, 
 Matthias Brugger <matthias.bgg@...il.com>, 
 AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>, 
 Russell King <linux@...linux.org.uk>
Cc: mithat.guner@...ont.com, erkin.bozoglu@...ont.com, 
 Bartel Eerdekens <bartel.eerdekens@...stell8.be>, netdev@...r.kernel.org, 
 linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org, 
 linux-mediatek@...ts.infradead.org, 
 Arınç ÜNAL <arinc.unal@...nc9.com>
Subject: [PATCH net-next v3 5/7] net: dsa: mt7530: simplify
 mt7530_setup_port6() and change to void

From: Arınç ÜNAL <arinc.unal@...nc9.com>

This code is from before this driver was converted to phylink API. Phylink
deals with the unsupported interface cases before mt7530_setup_port6() is
run. Therefore, the default case would never run. However, it must be
defined nonetheless to handle all the remaining enumeration values, the
phy-modes.

Switch to if statement for RGMII and return which simplifies the code and
saves an indent.

Set P6_INTF_MODE, which is the the three least significant bits of the
MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
after reset. This is to keep supporting dynamic reconfiguration of the port
in the case the interface changes from TRGMII to RGMII.

Disable the TRGMII clocks for all cases. They will be enabled if TRGMII is
being used.

Read XTAL after checking for RGMII as it's only needed for the TRGMII
interface mode.

Change mt7530_setup_port6() to void now that there're no error cases left.

Reviewed-by: Daniel Golle <daniel@...rotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
---
 drivers/net/dsa/mt7530.c | 101 ++++++++++++++++++++---------------------------
 1 file changed, 42 insertions(+), 59 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index c4d492e29fdf..e1fdef5766fb 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -414,70 +414,57 @@ mt753x_preferred_default_local_cpu_port(struct dsa_switch *ds)
 }
 
 /* Setup port 6 interface mode and TRGMII TX circuit */
-static int
+static void
 mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
-	u32 ncpo1, ssc_delta, trgint, xtal;
+	u32 ncpo1, ssc_delta, xtal;
 
-	xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
+	/* Disable the MT7530 TRGMII clocks */
+	core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
 
-	switch (interface) {
-	case PHY_INTERFACE_MODE_RGMII:
-		trgint = 0;
-		break;
-	case PHY_INTERFACE_MODE_TRGMII:
-		trgint = 1;
-		if (xtal == HWTRAP_XTAL_25MHZ)
-			ssc_delta = 0x57;
-		else
-			ssc_delta = 0x87;
-		if (priv->id == ID_MT7621) {
-			/* PLL frequency: 125MHz: 1.0GBit */
-			if (xtal == HWTRAP_XTAL_40MHZ)
-				ncpo1 = 0x0640;
-			if (xtal == HWTRAP_XTAL_25MHZ)
-				ncpo1 = 0x0a00;
-		} else { /* PLL frequency: 250MHz: 2.0Gbit */
-			if (xtal == HWTRAP_XTAL_40MHZ)
-				ncpo1 = 0x0c80;
-			if (xtal == HWTRAP_XTAL_25MHZ)
-				ncpo1 = 0x1400;
-		}
-		break;
-	default:
-		dev_err(priv->dev, "xMII interface %d not supported\n",
-			interface);
-		return -EINVAL;
+	if (interface == PHY_INTERFACE_MODE_RGMII) {
+		mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
+			   P6_INTF_MODE(0));
+		return;
 	}
 
-	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
-		   P6_INTF_MODE(trgint));
+	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK, P6_INTF_MODE(1));
 
-	if (trgint) {
-		/* Disable the MT7530 TRGMII clocks */
-		core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+	xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
 
-		/* Setup the MT7530 TRGMII Tx Clock */
-		core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
-		core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
-		core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
-		core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
-		core_write(priv, CORE_PLL_GROUP4,
-			   RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
-			   RG_SYSPLL_BIAS_LPF_EN);
-		core_write(priv, CORE_PLL_GROUP2,
-			   RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
-			   RG_SYSPLL_POSDIV(1));
-		core_write(priv, CORE_PLL_GROUP7,
-			   RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
-			   RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
+	if (xtal == HWTRAP_XTAL_25MHZ)
+		ssc_delta = 0x57;
+	else
+		ssc_delta = 0x87;
 
-		/* Enable the MT7530 TRGMII clocks */
-		core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+	if (priv->id == ID_MT7621) {
+		/* PLL frequency: 125MHz: 1.0GBit */
+		if (xtal == HWTRAP_XTAL_40MHZ)
+			ncpo1 = 0x0640;
+		if (xtal == HWTRAP_XTAL_25MHZ)
+			ncpo1 = 0x0a00;
+	} else { /* PLL frequency: 250MHz: 2.0Gbit */
+		if (xtal == HWTRAP_XTAL_40MHZ)
+			ncpo1 = 0x0c80;
+		if (xtal == HWTRAP_XTAL_25MHZ)
+			ncpo1 = 0x1400;
 	}
 
-	return 0;
+	/* Setup the MT7530 TRGMII Tx Clock */
+	core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
+	core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
+	core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
+	core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
+	core_write(priv, CORE_PLL_GROUP4, RG_SYSPLL_DDSFBK_EN |
+		   RG_SYSPLL_BIAS_EN | RG_SYSPLL_BIAS_LPF_EN);
+	core_write(priv, CORE_PLL_GROUP2, RG_SYSPLL_EN_NORMAL |
+		   RG_SYSPLL_VODEN | RG_SYSPLL_POSDIV(1));
+	core_write(priv, CORE_PLL_GROUP7, RG_LCDDS_PCW_NCPO_CHG |
+		   RG_LCCDS_C(3) | RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
+
+	/* Enable the MT7530 TRGMII clocks */
+	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
 }
 
 static void
@@ -2609,15 +2596,11 @@ mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 		  phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
-	int ret;
 
-	if (port == 5) {
+	if (port == 5)
 		mt7530_setup_port5(priv->ds, interface);
-	} else if (port == 6) {
-		ret = mt7530_setup_port6(priv->ds, interface);
-		if (ret)
-			return ret;
-	}
+	else if (port == 6)
+		mt7530_setup_port6(priv->ds, interface);
 
 	return 0;
 }

-- 
2.40.1


Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ