lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20240126-spi-omap2-mcspi-multi-mode-v1-2-d143d33f0fe0@bootlin.com>
Date: Tue, 06 Feb 2024 11:00:50 +0100
From: Louis Chauvet <louis.chauvet@...tlin.com>
To: Mark Brown <broonie@...nel.org>
Cc: linux-spi@...r.kernel.org, linux-kernel@...r.kernel.org, 
 thomas.petazzoni@...tlin.com, Miquel Raynal <miquel.raynal@...tlin.com>, 
 yen-mei.goh@...sight.com, koon-kee.lie@...sight.com, 
 Louis Chauvet <louis.chauvet@...tlin.com>
Subject: [PATCH 2/2] spi: omap2-mcspi: Add support for MULTI-mode

Introduce support for MULTI-mode in the OMAP2 MCSPI driver. Currently, the
driver always uses SINGLE mode to handle the chip select (CS). With this
enhancement, MULTI-mode is enabled for specific messages, allowing for a
shorter delay between CS enable and the message (some FPGA devices are
sensitive to this delay).

The drawback of multi-mode is that it's not possible to keep the CS
enabled between each words. Therefore, this patch enables multi-mode only
for specific messages: the spi_message must contain only spi_transfer of 1
word (of any size) with cs_change enabled.

A new member is introduced in the omap2_mcspi structure to keep track of
the current used mode.

Signed-off-by: Louis Chauvet <louis.chauvet@...tlin.com>
---
 drivers/spi/spi-omap2-mcspi.c | 57 ++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 51 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index fc7f69973334..ab22b1b062f3 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -133,6 +133,8 @@ struct omap2_mcspi {
 	unsigned int		pin_dir:1;
 	size_t			max_xfer_len;
 	u32			ref_clk_hz;
+
+	bool			use_multi_mode;
 };
 
 struct omap2_mcspi_cs {
@@ -258,10 +260,15 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
 
 		l = mcspi_cached_chconf0(spi);
 
-		if (enable)
+		/* Only enable chip select manually if single mode is used */
+		if (mcspi->use_multi_mode) {
 			l &= ~OMAP2_MCSPI_CHCONF_FORCE;
-		else
-			l |= OMAP2_MCSPI_CHCONF_FORCE;
+		} else {
+			if (enable)
+				l &= ~OMAP2_MCSPI_CHCONF_FORCE;
+			else
+				l |= OMAP2_MCSPI_CHCONF_FORCE;
+		}
 
 		mcspi_write_chconf0(spi, l);
 
@@ -285,7 +292,12 @@ static void omap2_mcspi_set_mode(struct spi_controller *ctlr)
 		l |= (OMAP2_MCSPI_MODULCTRL_MS);
 	} else {
 		l &= ~(OMAP2_MCSPI_MODULCTRL_MS);
-		l |= OMAP2_MCSPI_MODULCTRL_SINGLE;
+
+		/* Enable single mode if needed */
+		if (mcspi->use_multi_mode)
+			l &= ~OMAP2_MCSPI_MODULCTRL_SINGLE;
+		else
+			l |= OMAP2_MCSPI_MODULCTRL_SINGLE;
 	}
 	mcspi_write_reg(ctlr, OMAP2_MCSPI_MODULCTRL, l);
 
@@ -1371,15 +1383,48 @@ static int omap2_mcspi_prepare_message(struct spi_controller *ctlr,
 	struct omap2_mcspi	*mcspi = spi_controller_get_devdata(ctlr);
 	struct omap2_mcspi_regs	*ctx = &mcspi->ctx;
 	struct omap2_mcspi_cs	*cs;
+	struct spi_transfer	*tr;
+	u8 bits_per_word;
+	u32 speed_hz;
 
-	/* Only a single channel can have the FORCE bit enabled
+	/*
+	 * The conditions are strict, it is mandatory to check each transfer of the list to see if
+	 * multi-mode is applicable.
+	 */
+	mcspi->use_multi_mode = true;
+	list_for_each_entry(tr, &msg->transfers, transfer_list) {
+		if (!tr->bits_per_word)
+			bits_per_word = msg->spi->bits_per_word;
+		else
+			bits_per_word = tr->bits_per_word;
+
+		/* Check if the transfer content is only one word */
+		if ((bits_per_word < 8 && tr->len > 1) ||
+		    (bits_per_word >= 8 && tr->len > bits_per_word / 8))
+			mcspi->use_multi_mode = false;
+
+		/* Check if transfer asks to change the CS status after the transfer */
+		if (!tr->cs_change)
+			mcspi->use_multi_mode = false;
+
+		/* If at least one message is not compatible, switch back to single mode */
+		if (!mcspi->use_multi_mode)
+			break;
+	}
+
+	omap2_mcspi_set_mode(master);
+
+	/* In single mode only a single channel can have the FORCE bit enabled
 	 * in its chconf0 register.
 	 * Scan all channels and disable them except the current one.
 	 * A FORCE can remain from a last transfer having cs_change enabled
+	 *
+	 * In multi mode all FORCE bits must be disabled.
 	 */
 	list_for_each_entry(cs, &ctx->cs, node) {
-		if (msg->spi->controller_state == cs)
+		if (msg->spi->controller_state == cs && !mcspi->use_multi_mode) {
 			continue;
+		}
 
 		if ((cs->chconf0 & OMAP2_MCSPI_CHCONF_FORCE)) {
 			cs->chconf0 &= ~OMAP2_MCSPI_CHCONF_FORCE;

-- 
2.43.0


Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ