[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <23824242-1b37-4544-ae9a-0a5a0582580e@linaro.org>
Date: Tue, 6 Feb 2024 14:27:57 +0100
From: neil.armstrong@...aro.org
To: Krishna Kurapati <quic_kriskura@...cinc.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Rob Herring <robh+dt@...nel.org>, Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>, Conor Dooley <conor+dt@...nel.org>
Cc: linux-kernel@...r.kernel.org, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, quic_ppratap@...cinc.com,
quic_jackp@...cinc.com, Andrew Halaney <ahalaney@...hat.com>
Subject: Re: [PATCH 3/3] arm64: dts: qcom: sa8540-ride: Enable first port of
tertiary usb controller
On 06/02/2024 12:47, Krishna Kurapati wrote:
> From: Andrew Halaney <ahalaney@...hat.com>
>
> There is now support for the multiport USB controller this uses so
> enable it.
>
> The board only has a single port hooked up (despite it being wired up to
> the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
> which by default on boot is selected to mux properly. Grab the gpio
> controlling that and ensure it stays in the right position so USB 2.0
> continues to be routed from the external port to the SoC.
>
> Signed-off-by: Andrew Halaney <ahalaney@...hat.com>
> Co-developed-by: Krishna Kurapati <quic_kriskura@...cinc.com>
> Signed-off-by: Krishna Kurapati <quic_kriskura@...cinc.com>
> ---
> arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index b04f72ec097c..eed1ddc29bc1 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -503,6 +503,18 @@ &usb_2_qmpphy0 {
> status = "okay";
> };
>
> +&usb_2 {
> + pinctrl-0 = <&usb2_en>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + phy-names = "usb2-port0", "usb3-port0";
> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
> +};
> +
> &xo_board_clk {
> clock-frequency = <38400000>;
> };
> @@ -655,4 +667,13 @@ wake-pins {
> bias-pull-up;
> };
> };
> +
> + usb2_en: usb2-en-state {
> + /* TS3USB221A USB2.0 mux select */
> + pins = "gpio24";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> };
Isn't gpio-hog the preferred way to describe that ?
Neil
Powered by blists - more mailing lists