| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAA8EJppHv9g4HnEFaEaCH=FnvJdnFfnr+rt=Onyqh-er8UA6TQ@mail.gmail.com>
Date: Mon, 12 Feb 2024 23:19:40 +0200
From: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
To: Konrad Dybcio <konrad.dybcio@...aro.org>
Cc: Bjorn Andersson <andersson@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, Conor Dooley <conor+dt@...nel.org>,
Marijn Suijten <marijn.suijten@...ainline.org>, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH] arm64: dts: qcom: sm6115p-j606f: Add some peripherals
On Mon, 12 Feb 2024 at 15:44, Konrad Dybcio <konrad.dybcio@...aro.org> wrote:
>
> This tablet features quite a bunch of I2C-connected devices, such as
> a Richtek RT1715 USB-C controller, a MM8013 fuel gauge, FSA4480 Type-C
> audio mux, TPS65132 regulator and some more.
>
> Add the aforementioned ones and document others.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@...aro.org>
> ---
> arch/arm64/boot/dts/qcom/sm6115.dtsi | 7 ++
> arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 103 +++++++++++++++++++++-
> 2 files changed, 109 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> index ee65ab073ba6..7df7b2045b71 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> @@ -1676,6 +1676,13 @@ usb_dwc3_ss: endpoint {
> remote-endpoint = <&usb_qmpphy_usb_ss_in>;
> };
> };
> +
> + port@2 {
> + reg = <2>;
> +
> + usb_dwc3_sbu: endpoint {
> + };
The SBU lines are not connected to the DWC3 port
> + };
> };
> };
> };
> diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
> index 54da053a8042..eb65c2806345 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
> @@ -73,6 +73,81 @@ zap-shader {
> };
> };
>
> +&gpi_dma0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + /* Some devices use FUSB302(@22) instead of the RT1715. */
> +
> + rt1715: typec-portc@4e {
> + compatible = "richtek,rt1715";
> + reg = <0x4e>;
> + interrupts-extended = <&tlmm 97 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-0 = <&typec_int>;
> + pinctrl-names = "default";
> +
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + data-role = "dual";
> +
> + /* TODO: Add a proper PD setup */
> + typec-power-opmode = "default";
> + try-power-role = "sink";
> + power-role = "dual";
> + pd-disable;
> +
> + port {
> + rt1715_hs_ep: endpoint {
> + remote-endpoint = <&usb_dwc3_hs>;
Most likely this port should have the SBU endpoint connected to
fsa4480. Also, if SS lines are connected, there should be a link
between this connector and the QMP PHY.
> + };
> + };
> + };
> + };
> +
> + fuel-gauge@55 {
> + compatible = "mitsumi,mm8013";
> + reg = <0x55>;
> + };
> +
> + /* AW882xx speaker amp @ 34, 35, 36, 37 (CHIP_ID = 0x1852) */
> + /* HID-over-I2C for the touchpad on keyboard folio @ 60 */
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + tps65132@3e {
> + compatible = "ti,tps65132";
> + reg = <0x3e>;
> + };
> +
> + fsa4480: typec-mux@42 {
> + compatible = "fcs,fsa4480";
> + reg = <0x42>;
> + interrupts-extended = <&tlmm 89 IRQ_TYPE_LEVEL_LOW>;
> + orientation-switch;
> + mode-switch;
> +
> + port {
> + fsa4480_sbu_mux: endpoint {
> + remote-endpoint = <&usb_dwc3_sbu>;
> + };
> + };
> + };
> +
> + /* PM8008 @ 8, 9 */
> + /* SMB1355 @ c */
> + /* SGM37604A WLED driver @ 36 */
> + /* ES7210 audio ADC @ 40 */
> + /* HID-over-I2C for the keyboard on keyboard folio @ 61 */
> +};
> +
> &mdss {
> status = "okay";
> };
> @@ -129,6 +204,10 @@ &pon_resin {
> status = "okay";
> };
>
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> &remoteproc_adsp {
> firmware-name = "qcom/sm6115/LENOVO/J606F/adsp.mbn";
> status = "okay";
> @@ -309,6 +388,12 @@ &sleep_clk {
> clock-frequency = <32764>;
> };
>
> +&spi2 {
> + status = "okay";
> +
> + /* HIMAX83102P or NT36523W touchscreen */
> +};
> +
> &tlmm {
> gpio-reserved-ranges = <14 4>;
>
> @@ -337,6 +422,14 @@ mdss_dsi_active: dsi-active-state {
> drive-strength = <8>;
> bias-disable;
> };
> +
> + typec_int: typec-int-state {
> + pins = "gpio97";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + input-enable;
> + };
> };
>
> &ufs_mem_hc {
> @@ -360,12 +453,20 @@ &usb {
>
> &usb_dwc3 {
> maximum-speed = "high-speed";
> - dr_mode = "peripheral";
> + dr_mode = "otg";
>
> phys = <&usb_hsphy>;
> phy-names = "usb2-phy";
> };
>
> +&usb_dwc3_hs {
> + remote-endpoint = <&rt1715_hs_ep>;
> +};
> +
> +&usb_dwc3_sbu {
> + remote-endpoint = <&fsa4480_sbu_mux>;
> +};
> +
> &usb_hsphy {
> vdd-supply = <&pm6125_l4>;
> vdda-pll-supply = <&pm6125_l12>;
>
> ---
> base-commit: ae00c445390b349e070a64dc62f08aa878db7248
> change-id: 20240212-topic-j606f_periphs-87dd893e105c
>
> Best regards,
> --
> Konrad Dybcio <konrad.dybcio@...aro.org>
>
>
--
With best wishes
Dmitry
Powered by blists - more mailing lists