Message-Id: <20240227-mbly-clk-v8-3-c57fbda7664a@bootlin.com>
Date: Tue, 27 Feb 2024 15:55:24 +0100
From: Théo Lebrun <theo.lebrun@...tlin.com>
To: Gregory CLEMENT <gregory.clement@...tlin.com>, 
 Michael Turquette <mturquette@...libre.com>, 
 Stephen Boyd <sboyd@...nel.org>, Rob Herring <robh+dt@...nel.org>, 
 Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, 
 Conor Dooley <conor+dt@...nel.org>, 
 Thomas Bogendoerfer <tsbogend@...ha.franken.de>, 
 Linus Walleij <linus.walleij@...aro.org>, 
 Rafał Miłecki <rafal@...ecki.pl>, 
 Philipp Zabel <p.zabel@...gutronix.de>
Cc: Vladimir Kondratiev <vladimir.kondratiev@...ileye.com>, 
 linux-mips@...r.kernel.org, linux-clk@...r.kernel.org, 
 devicetree@...r.kernel.org, linux-kernel@...r.kernel.org, 
 Thomas Petazzoni <thomas.petazzoni@...tlin.com>, 
 Tawfik Bayouk <tawfik.bayouk@...ileye.com>, linux-gpio@...r.kernel.org, 
 Théo Lebrun <theo.lebrun@...tlin.com>
Subject: [PATCH v8 03/10] clk: eyeq5: add platform driver, and init routine
 at of_clk_init()

Add the Mobileye EyeQ5 clock controller driver. It might grow to add
support for other platforms from Mobileye.

It handles 10 read-only PLLs derived from the main crystal on board. It
exposes a table-based divider clock used for OSPI. Other platform
clocks are not configurable and therefore kept as fixed-factor
devicetree nodes.

Two PLLs are required early on and are therefore registered at
of_clk_init(). Those are pll-cpu for the GIC timer and pll-per for the
UARTs.

Signed-off-by: Théo Lebrun <theo.lebrun@...tlin.com>
---
 drivers/clk/Kconfig     |  11 ++
 drivers/clk/Makefile    |   1 +
 drivers/clk/clk-eyeq5.c | 306 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 318 insertions(+)

diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 50af5fc7f570..c79b38f60b1b 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -218,6 +218,17 @@ config COMMON_CLK_EN7523
 	  This driver provides the fixed clocks and gates present on Airoha
 	  ARM silicon.
 
+config COMMON_CLK_EYEQ5
+	bool "Clock driver for the Mobileye EyeQ5 platform"
+	depends on OF
+	depends on MACH_EYEQ5 || COMPILE_TEST
+	default MACH_EYEQ5
+	help
+	  This driver provides the clocks found on the Mobileye EyeQ5 SoC. Its
+	  registers live in a shared register region called OLB. It provides 10
+	  read-only PLLs derived from the main crystal clock which must be constant
+	  and one divider clock based on one PLL.
+
 config COMMON_CLK_FSL_FLEXSPI
 	tristate "Clock driver for FlexSPI on Layerscape SoCs"
 	depends on ARCH_LAYERSCAPE || COMPILE_TEST
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 14fa8d4ecc1f..81c4d11ca437 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_ARCH_CLPS711X)		+= clk-clps711x.o
 obj-$(CONFIG_COMMON_CLK_CS2000_CP)	+= clk-cs2000-cp.o
 obj-$(CONFIG_ARCH_SPARX5)		+= clk-sparx5.o
 obj-$(CONFIG_COMMON_CLK_EN7523)		+= clk-en7523.o
+obj-$(CONFIG_COMMON_CLK_EYEQ5)		+= clk-eyeq5.o
 obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)	+= clk-fixed-mmio.o
 obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI)	+= clk-fsl-flexspi.o
 obj-$(CONFIG_COMMON_CLK_FSL_SAI)	+= clk-fsl-sai.o
diff --git a/drivers/clk/clk-eyeq5.c b/drivers/clk/clk-eyeq5.c
new file mode 100644
index 000000000000..85bf6f1c3fa3
--- /dev/null
+++ b/drivers/clk/clk-eyeq5.c
@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PLL clock driver for the Mobileye EyeQ5 platform.
+ *
+ * This controller handles 10 read-only PLLs, all derived from the same main
+ * crystal clock. It also exposes one divider clock, a child of one of the
+ * PLLs. The parent clock is expected to be constant. This driver's registers
+ * live in a shared region called OLB. Two PLLs must be initialized by
+ * of_clk_init().
+ *
+ * We use eq5c_ as prefix, as-in "EyeQ5 Clock", but way shorter.
+ *
+ * Copyright (C) 2024 Mobileye Vision Technologies Ltd.
+ */
+
+#define pr_fmt(fmt) "clk-eyeq5: " fmt
+
+#include <linux/array_size.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/printk.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/clock/mobileye,eyeq5-clk.h>
+
+/* In frac mode, it enables fractional noise canceling DAC. Else, no function. */
+#define PCSR0_DAC_EN			BIT(0)
+/* Fractional or integer mode */
+#define PCSR0_DSM_EN			BIT(1)
+#define PCSR0_PLL_EN			BIT(2)
+/* All clocks output held at 0 */
+#define PCSR0_FOUTPOSTDIV_EN		BIT(3)
+#define PCSR0_POST_DIV1			GENMASK(6, 4)
+#define PCSR0_POST_DIV2			GENMASK(9, 7)
+#define PCSR0_REF_DIV			GENMASK(15, 10)
+#define PCSR0_INTIN			GENMASK(27, 16)
+#define PCSR0_BYPASS			BIT(28)
+/* Bits 30..29 are reserved */
+#define PCSR0_PLL_LOCKED		BIT(31)
+
+#define PCSR1_RESET			BIT(0)
+#define PCSR1_SSGC_DIV			GENMASK(4, 1)
+/* Spread amplitude (% = 0.1 * SPREAD[4:0]) */
+#define PCSR1_SPREAD			GENMASK(9, 5)
+#define PCSR1_DIS_SSCG			BIT(10)
+/* Down-spread or center-spread */
+#define PCSR1_DOWN_SPREAD		BIT(11)
+#define PCSR1_FRAC_IN			GENMASK(31, 12)
+
+static struct clk_hw_onecell_data *eq5c_clk_data;
+
+struct eq5c_pll {
+	int		index;
+	const char	*name;
+	u32		reg;	/* next 8 bytes are r0 and r1 */
+};
+
+/* Required early for the GIC timer (pll-cpu) and UARTs (pll-per). */
+static const struct eq5c_pll eq5c_early_plls[] = {
+	{ .index = EQ5C_PLL_CPU, .name = "pll-cpu",  .reg = 0x00, },
+	{ .index = EQ5C_PLL_PER, .name = "pll-per",  .reg = 0x30, },
+};
+
+static const struct eq5c_pll eq5c_plls[] = {
+	{ .index = EQ5C_PLL_VMP,  .name = "pll-vmp",  .reg = 0x08, },
+	{ .index = EQ5C_PLL_PMA,  .name = "pll-pma",  .reg = 0x10, },
+	{ .index = EQ5C_PLL_VDI,  .name = "pll-vdi",  .reg = 0x18, },
+	{ .index = EQ5C_PLL_DDR0, .name = "pll-ddr0", .reg = 0x20, },
+	{ .index = EQ5C_PLL_PCI,  .name = "pll-pci",  .reg = 0x28, },
+	{ .index = EQ5C_PLL_PMAC, .name = "pll-pmac", .reg = 0x38, },
+	{ .index = EQ5C_PLL_MPC,  .name = "pll-mpc",  .reg = 0x40, },
+	{ .index = EQ5C_PLL_DDR1, .name = "pll-ddr1", .reg = 0x48, },
+};
+
+#define EQ5C_OSPI_DIV_CLK_NAME	"div-ospi"
+#define EQ5C_OSPI_DIV_WIDTH	4
+
+#define EQ5C_NB_CLKS	(ARRAY_SIZE(eq5c_early_plls) + ARRAY_SIZE(eq5c_plls) + 1)
+
+static const struct clk_div_table eq5c_ospi_div_table[] = {
+	{ .val = 0, .div = 2 },
+	{ .val = 1, .div = 4 },
+	{ .val = 2, .div = 6 },
+	{ .val = 3, .div = 8 },
+	{ .val = 4, .div = 10 },
+	{ .val = 5, .div = 12 },
+	{ .val = 6, .div = 14 },
+	{ .val = 7, .div = 16 },
+	{} /* sentinel */
+};
+
+static int eq5c_pll_parse_registers(u32 r0, u32 r1, unsigned long *mult,
+				    unsigned long *div, unsigned long *acc)
+{
+	if (r0 & PCSR0_BYPASS) {
+		*mult = 1;
+		*div = 1;
+		*acc = 0;
+		return 0;
+	}
+
+	if (!(r0 & PCSR0_PLL_LOCKED))
+		return -EINVAL;
+
+	*mult = FIELD_GET(PCSR0_INTIN, r0);
+	*div = FIELD_GET(PCSR0_REF_DIV, r0);
+	if (r0 & PCSR0_FOUTPOSTDIV_EN)
+		*div *= FIELD_GET(PCSR0_POST_DIV1, r0) * FIELD_GET(PCSR0_POST_DIV2, r0);
+
+	/* Fractional mode, in 2^20 (0x100000) parts. */
+	if (r0 & PCSR0_DSM_EN) {
+		*div *= 0x100000;
+		*mult = *mult * 0x100000 + FIELD_GET(PCSR1_FRAC_IN, r1);
+	}
+
+	if (!*mult || !*div)
+		return -EINVAL;
+
+	/* Spread spectrum. */
+	if (!(r1 & (PCSR1_RESET | PCSR1_DIS_SSCG))) {
+		/*
+		 * Spread is 1/1000 parts of frequency, accuracy is half of
+		 * that. To get accuracy, convert to ppb (parts per billion).
+		 */
+		u32 spread = FIELD_GET(PCSR1_SPREAD, r1);
+
+		*acc = spread * 500000;
+		if (r1 & PCSR1_DOWN_SPREAD) {
+			/*
+			 * Downspreading: the central frequency is half a
+			 * spread lower.
+			 */
+			*mult *= 2000 - spread;
+			*div *= 2000;
+		}
+	} else {
+		*acc = 0;
+	}
+
+	return 0;
+}
+
+static int eq5c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	void __iomem *base_plls, *base_ospi;
+	struct clk_hw *hw;
+	int i;
+
+	/* Return potential error from eq5c_init(). */
+	if (IS_ERR(eq5c_clk_data))
+		return PTR_ERR(eq5c_clk_data);
+	/* Return an error if eq5c_init() did not get called. */
+	else if (!eq5c_clk_data)
+		return -EINVAL;
+
+	base_plls = devm_platform_ioremap_resource_byname(pdev, "plls");
+	if (IS_ERR(base_plls))
+		return PTR_ERR(base_plls);
+
+	base_ospi = devm_platform_ioremap_resource_byname(pdev, "ospi");
+	if (IS_ERR(base_ospi))
+		return PTR_ERR(base_ospi);
+
+	for (i = 0; i < ARRAY_SIZE(eq5c_plls); i++) {
+		const struct eq5c_pll *pll = &eq5c_plls[i];
+		unsigned long mult, div, acc;
+		u32 r0, r1;
+		int ret;
+
+		r0 = readl(base_plls + pll->reg);
+		r1 = readl(base_plls + pll->reg + sizeof(r0));
+
+		ret = eq5c_pll_parse_registers(r0, r1, &mult, &div, &acc);
+		if (ret) {
+			dev_warn(dev, "failed parsing state of %s\n", pll->name);
+			eq5c_clk_data->hws[pll->index] = ERR_PTR(ret);
+			continue;
+		}
+
+		hw = clk_hw_register_fixed_factor_with_accuracy_fwname(dev, np,
+				pll->name, "ref", 0, mult, div, acc);
+		eq5c_clk_data->hws[pll->index] = hw;
+		if (IS_ERR(hw))
+			dev_err_probe(dev, PTR_ERR(hw), "failed registering %s\n",
+				      pll->name);
+	}
+
+	hw = clk_hw_register_divider_table_parent_hw(dev, EQ5C_OSPI_DIV_CLK_NAME,
+			eq5c_clk_data->hws[EQ5C_PLL_PER], 0,
+			base_ospi, 0, EQ5C_OSPI_DIV_WIDTH, 0,
+			eq5c_ospi_div_table, NULL);
+	eq5c_clk_data->hws[EQ5C_DIV_OSPI] = hw;
+	if (IS_ERR(hw))
+		dev_err_probe(dev, PTR_ERR(hw), "failed registering %s\n",
+			      EQ5C_OSPI_DIV_CLK_NAME);
+
+	return 0;
+}
+
+static const struct of_device_id eq5c_match_table[] = {
+	{ .compatible = "mobileye,eyeq5-clk" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, eq5c_match_table);
+
+static struct platform_driver eq5c_driver = {
+	.probe = eq5c_probe,
+	.driver = {
+		.name = "clk-eyeq5",
+		.of_match_table = eq5c_match_table,
+	},
+};
+builtin_platform_driver(eq5c_driver);
+
+static void __init eq5c_init(struct device_node *np)
+{
+	void __iomem *base_plls, *base_ospi;
+	int index_plls, index_ospi;
+	int i, ret;
+
+	eq5c_clk_data = kzalloc(struct_size(eq5c_clk_data, hws, EQ5C_NB_CLKS),
+				GFP_KERNEL);
+	if (!eq5c_clk_data) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	eq5c_clk_data->num = EQ5C_NB_CLKS;
+
+	/*
+	 * Mark all clocks as deferred. We register some now and others at
+	 * platform device probe.
+	 */
+	for (i = 0; i < EQ5C_NB_CLKS; i++)
+		eq5c_clk_data->hws[i] = ERR_PTR(-EPROBE_DEFER);
+
+	index_plls = of_property_match_string(np, "reg-names", "plls");
+	if (index_plls < 0) {
+		ret = index_plls;
+		goto err;
+	}
+
+	index_ospi = of_property_match_string(np, "reg-names", "ospi");
+	if (index_ospi < 0) {
+		ret = index_ospi;
+		goto err;
+	}
+
+	base_plls = of_iomap(np, index_plls);
+	base_ospi = of_iomap(np, index_ospi);
+	if (!base_plls || !base_ospi) {
+		ret = -ENODEV;
+		goto err;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(eq5c_early_plls); i++) {
+		const struct eq5c_pll *pll = &eq5c_early_plls[i];
+		unsigned long mult, div, acc;
+		struct clk_hw *hw;
+		u32 r0, r1;
+
+		r0 = readl(base_plls + pll->reg);
+		r1 = readl(base_plls + pll->reg + sizeof(r0));
+
+		ret = eq5c_pll_parse_registers(r0, r1, &mult, &div, &acc);
+		if (ret) {
+			pr_warn("failed parsing state of %s\n", pll->name);
+			eq5c_clk_data->hws[pll->index] = ERR_PTR(ret);
+			continue;
+		}
+
+		hw = clk_hw_register_fixed_factor_with_accuracy_fwname(NULL,
+				np, pll->name, "ref", 0, mult, div, acc);
+		eq5c_clk_data->hws[pll->index] = hw;
+		if (IS_ERR(hw))
+			pr_err("failed registering %s: %ld\n",
+			       pll->name, PTR_ERR(hw));
+	}
+
+	ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, eq5c_clk_data);
+	if (ret) {
+		pr_err("failed registering clk provider: %d\n", ret);
+		goto err;
+	}
+
+	return;
+
+err:
+	kfree(eq5c_clk_data);
+	/* Signal to platform driver probe that we failed init. */
+	eq5c_clk_data = ERR_PTR(ret);
+}
+
+CLK_OF_DECLARE_DRIVER(eq5c, "mobileye,eyeq5-clk", eq5c_init);

-- 
2.44.0

Powered by blists - more mailing lists