| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20240305-b4-for-v6-9-am65-beagleplay-ethernet-reset-v2-1-2bf463a7bf13@kernel.org>
Date: Tue, 05 Mar 2024 15:15:32 +0200
From: Roger Quadros <rogerq@...nel.org>
To: Nishanth Menon <nm@...com>, Vignesh Raghavendra <vigneshr@...com>,
Tero Kristo <kristo@...nel.org>, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: srk@...com, s-vadapalli@...com, r-gunasekaran@...com,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, Roger Quadros <rogerq@...nel.org>
Subject: [PATCH v2] arm64: dts: ti: beagleplay: Fix Ethernet PHY RESET
GPIOs
The RESET GPIO pinmux should be part of MDIO bus node
so that they can be in the right state before the PHY
can be probed via MDIO bus scan.
The GPIO pin should be setup with PIN_INPUT so that
input circuitry is enabled in case software wants to
check pin status. Without this, incorrect status is shown
in /sys/kernel/debug/gpio.
Add GPIO reset for the Gigabit Ethernet PHY. As per
RTL8211F datasheet, reset assert width is 10ms and
PHY registers can be access accessed after 50ms of
reset deassert.
Fixes: f5a731f0787f ("arm64: dts: ti: Add k3-am625-beagleplay")
Signed-off-by: Roger Quadros <rogerq@...nel.org>
---
Changes in v2:
- Fix Subject to "arm64"
- Enable PIN_INPUT for SPE_RESET to fix GPIO status.
- Add Fixes tag.
- Link to v1: https://lore.kernel.org/r/20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-v1-1-b3e4b33378bd@kernel.org
---
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
index a34e0df2ab86..8ab838f1697c 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -292,6 +292,8 @@ mdio0_pins_default: mdio0-default-pins {
pinctrl-single,pins = <
AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+ AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
+ AM62X_IOPAD(0x018c, PIN_INPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
>;
};
@@ -383,7 +385,6 @@ AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
- AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
>;
@@ -597,6 +598,9 @@ &cpsw3g_mdio {
cpsw3g_phy0: ethernet-phy@0 {
reg = <0>;
+ reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
};
cpsw3g_phy1: ethernet-phy@1 {
@@ -615,7 +619,7 @@ &main_gpio0 {
"USR0", "USR1", "USR2", "USR3", "", "", "USR4", /* 3-9 */
"EEPROM_WP", /* 10 */
"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2", /* 11-12 */
- "CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "", /* 13-17 */
+ "CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "", /* 13-17 */
"USR_BUTTON", "", "", "", "", "", "", "", "", /* 18-26 */
"", "", "", "", "", "", "", "", "", "HDMI_INT", /* 27-36 */
"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
---
base-commit: bbef42084cc170cbfc035bf784f2ff055c939d7e
change-id: 20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-098f274fbf15
Best regards,
--
Roger Quadros <rogerq@...nel.org>
Powered by blists - more mailing lists