| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZfRlYnEQUKvwGQ65@gerhold.net>
Date: Fri, 15 Mar 2024 16:12:34 +0100
From: Stephan Gerhold <stephan@...hold.net>
To: Sumit Garg <sumit.garg@...aro.org>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
andersson@...nel.org, konrad.dybcio@...aro.org, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org, conor+dt@...nel.org,
caleb.connolly@...aro.org, neil.armstrong@...aro.org,
dmitry.baryshkov@...aro.org, laetitia.mariottini@...com,
pascal.eberhard@...com, abdou.saker@...com, jimmy.lalande@...com,
benjamin.missey@....se.com, daniel.thompson@...aro.org,
linux-kernel@...r.kernel.org,
Jagdish Gediya <jagdish.gediya@...aro.org>
Subject: Re: [PATCH v3 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC
board DTS
On Fri, Mar 15, 2024 at 11:37:07AM +0530, Sumit Garg wrote:
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC.
>
> Support for Schneider Electric HMIBSC. Features:
> - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> - 1GiB RAM
> - 8GiB eMMC, SD slot
> - WiFi and Bluetooth
> - 2x Host, 1x Device USB port
> - HDMI
> - Discrete TPM2 chip over SPI
> - USB ethernet adaptors (soldered)
>
> Co-developed-by: Jagdish Gediya <jagdish.gediya@...aro.org>
> Signed-off-by: Jagdish Gediya <jagdish.gediya@...aro.org>
> Reviewed-by: Caleb Connolly <caleb.connolly@...aro.org>
> Signed-off-by: Sumit Garg <sumit.garg@...aro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/apq8016-schneider-hmibsc.dts | 510 ++++++++++++++++++
> 2 files changed, 511 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 39889d5f8e12..ad55e52e950b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -5,6 +5,7 @@ apq8016-sbc-usb-host-dtbs := apq8016-sbc.dtb apq8016-sbc-usb-host.dtbo
>
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-usb-host.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3-camera-mezzanine.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += apq8016-schneider-hmibsc.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> new file mode 100644
> index 000000000000..9c79a31a04db
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> @@ -0,0 +1,510 @@
> [...]
> +&blsp_uart1 {
> + label = "UART0";
> + status = "okay";
> +};
> +
> +&blsp_uart2 {
> + label = "UART1";
> + status = "okay";
> +};
> +
> +/* Enable CoreSight */
> +&cti0 { status = "okay"; };
> +&cti1 { status = "okay"; };
> +&cti12 { status = "okay"; };
> +&cti13 { status = "okay"; };
> +&cti14 { status = "okay"; };
> +&cti15 { status = "okay"; };
> +&debug0 { status = "okay"; };
> +&debug1 { status = "okay"; };
> +&debug2 { status = "okay"; };
> +&debug3 { status = "okay"; };
> +&etf { status = "okay"; };
> +&etm0 { status = "okay"; };
> +&etm1 { status = "okay"; };
> +&etm2 { status = "okay"; };
> +&etm3 { status = "okay"; };
> +&etr { status = "okay"; };
> +&funnel0 { status = "okay"; };
> +&funnel1 { status = "okay"; };
> +&replicator { status = "okay"; };
> +&stm { status = "okay"; };
> +&tpiu { status = "okay"; };
Nitpick: The &cti0 is in the correct alphabetically ordered place, but
&replicator, &stm and &tpiu are not.
I know you changed this based on the review comments but I personally
think it was clearer having this separated as condensed block towards
the end of the file (where it was before).
The other option would be to put each element individually at the
correctly ordered position in the file. However, having a single "Enable
CoreSight" comment for the entire block would then not work anymore
since all the lines would be interspersed throughout the file.
> [...]
> +&pm8916_codec {
> + qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
> + qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
> + status = "okay";
> +};
> +
> +&pm8916_gpios {
> + gpio-line-names =
> + "USB_HUB_RESET_N_PM",
> + "USB_SW_SEL_PM",
> + "NC",
> + "NC";
> +
> + usb_hub_reset_pm: usb-hub-reset-pm-state {
> + pins = "gpio1";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + input-disable;
> + output-high;
> + };
> +
> + usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
> + pins = "gpio1";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + output-low;
> + };
> +
> + usb_sw_sel_pm: usb-sw-sel-pm-state {
> + pins = "gpio2";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + power-source = <PM8916_GPIO_VPH>;
> + input-disable;
> + output-high;
> + };
> +
> + usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
> + pins = "gpio2";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + power-source = <PM8916_GPIO_VPH>;
> + input-disable;
> + output-low;
> + };
> +};
> +
> +&pm8916_mpps {
> + gpio-line-names =
> + "NC",
> + "WLAN_LED_CTRL",
> + "BT_LED_CTRL",
> + "NC";
> +
> + pm8916_mpps_leds: pm8916-mpps-state {
> + pins = "mpp2", "mpp3";
> + function = "digital";
> +
> + output-low;
> + };
> +};
> +
> +&pm8916_resin {
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_FALLING>;
What is the goal of overriding the interrupt here? It looks like you are
changing the interrupt type from IRQ_TYPE_EDGE_BOTH to FALLING. This
sounds a bit like you want the driver to receive just button release
events (or just press events, not sure about the polarity). I'm not sure
if the driver will handle this correctly.
> + linux,code = <KEY_POWER>;
> + status = "okay";
> +};
> +
> +&pm8916_rpm_regulators {
> + pm8916_l17: l17 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +};
> +
> +&sdhc_1 {
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
> + pinctrl-names = "default", "sleep";
> +
> + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&sound {
> + pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
> + pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
> + pinctrl-names = "default", "sleep";
> + model = "HMIBSC";
> + audio-routing =
> + "AMIC2", "MIC BIAS Internal2",
> + "AMIC3", "MIC BIAS External1";
> + status = "okay";
> +
> + quaternary-dai-link {
> + link-name = "ADV7533";
> + cpu {
> + sound-dai = <&lpass MI2S_QUATERNARY>;
> + };
> + codec {
> + sound-dai = <&adv_bridge 0>;
> + };
> + };
> +
> + primary-dai-link {
> + link-name = "WCD";
> + cpu {
> + sound-dai = <&lpass MI2S_PRIMARY>;
> + };
> + codec {
> + sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
> + };
> + };
> +
> + tertiary-dai-link {
> + link-name = "WCD-Capture";
> + cpu {
> + sound-dai = <&lpass MI2S_TERTIARY>;
> + };
> + codec {
> + sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
> + };
> + };
> +};
> +
> +&tlmm {
> + pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>;
> + pinctrl-names = "default";
> +
> + adv7533_int_active: adv533-int-active-state {
> + pins = "gpio31";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + adv7533_int_suspend: adv7533-int-suspend-state {
> + pins = "gpio31";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + adv7533_switch_active: adv7533-switch-active-state {
> + pins = "gpio32";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + adv7533_switch_suspend: adv7533-switch-suspend-state {
> + pins = "gpio32";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + msm_key_volp_n_default: msm-key-volp-n-default-state {
> + pins = "gpio107";
> + function = "gpio";
> +
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + sdc2_cd_default: sdc2-cd-default-state {
> + pins = "gpio38";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
Nitpick: It would look a bit cleaner to have the empty lines consistent
in all pinctrl nodes, i.e. either always having an empty line between
function and drive-strength or never. I think Konrad prefers the more
compact version without empty line (sadly I'm not sure if this is
clearly documented anywhere). Same for &pm8916_gpios and mpps.
> +
> + /*
> + * UART1 being the debug console supports various modes of
> + * operation (RS-232/485/422) controlled via GPIOs configured
> + * mux as follows:
> + *
> + * gpio100 gpio99 UART mode
> + * 0 0 loopback
> + * 0 1 RS-232
> + * 1 0 RS-485
> + * 1 1 RS-422
> + *
> + * The default mode configured here is RS-232 mode.
> + */
:D
Thanks a lot for making this clear using the table. And also for all the
other cleanup changes!
Stephan
Powered by blists - more mailing lists