[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <8799b216-57a7-451b-80a3-3d4ae9693e0b@linaro.org>
Date: Fri, 15 Mar 2024 21:35:58 +0100
From: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To: Ayush Singh <ayushdevel1325@...il.com>, linux-kernel@...r.kernel.org
Cc: jkridner@...gleboard.org, robertcnelson@...gleboard.org,
Vaishnav M A <vaishnav@...gleboard.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>, Nishanth Menon <nm@...com>,
Vignesh Raghavendra <vigneshr@...com>, Tero Kristo <kristo@...nel.org>,
Derek Kiernan <derek.kiernan@....com>, Dragan Cvetic
<dragan.cvetic@....com>, Arnd Bergmann <arnd@...db.de>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Liam Girdwood <lgirdwood@...il.com>, Mark Brown <broonie@...nel.org>,
Jiri Slaby <jirislaby@...nel.org>, Johan Hovold <johan@...nel.org>,
Alex Elder <elder@...nel.org>, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-spi@...r.kernel.org,
linux-serial@...r.kernel.org, greybus-dev@...ts.linaro.org
Subject: Re: [PATCH v3 7/8] mikrobus: Add mikrobus driver
On 15/03/2024 19:49, Ayush Singh wrote:
> - Setup I2C, SPI, serdev controllers associated with mikrobus connector
> - Check if a board with valid mikroBUS manifest is connected
> - Parse the manifest and register the device to kernel
>
> Signed-off-by: Vaishnav M A <vaishnav@...gleboard.org>
> Signed-off-by: Ayush Singh <ayushdevel1325@...il.com>
> ---
> MAINTAINERS | 1 +
> drivers/misc/Kconfig | 1 +
> drivers/misc/Makefile | 1 +
> drivers/misc/mikrobus/Kconfig | 19 +
> drivers/misc/mikrobus/Makefile | 6 +
> drivers/misc/mikrobus/mikrobus_core.c | 942 ++++++++++++++++++++++
> drivers/misc/mikrobus/mikrobus_core.h | 201 +++++
> drivers/misc/mikrobus/mikrobus_id.c | 229 ++++++
> drivers/misc/mikrobus/mikrobus_manifest.c | 502 ++++++++++++
> drivers/misc/mikrobus/mikrobus_manifest.h | 20 +
> 10 files changed, 1922 insertions(+)
> create mode 100644 drivers/misc/mikrobus/Kconfig
> create mode 100644 drivers/misc/mikrobus/Makefile
> create mode 100644 drivers/misc/mikrobus/mikrobus_core.c
> create mode 100644 drivers/misc/mikrobus/mikrobus_core.h
> create mode 100644 drivers/misc/mikrobus/mikrobus_id.c
> create mode 100644 drivers/misc/mikrobus/mikrobus_manifest.c
> create mode 100644 drivers/misc/mikrobus/mikrobus_manifest.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 69418a058c6b..83bc5e48bef9 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14772,6 +14772,7 @@ M: Ayush Singh <ayushdevel1325@...il.com>
> M: Vaishnav M A <vaishnav@...gleboard.org>
> S: Maintained
> F: Documentation/devicetree/bindings/misc/mikrobus-connector.yaml
> +F: drivers/misc/mikrobus/*
>
> MIKROTIK CRS3XX 98DX3236 BOARD SUPPORT
> M: Luka Kovacic <luka.kovacic@...tura.hr>
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 4fb291f0bf7c..3d5c36205c6c 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -591,4 +591,5 @@ source "drivers/misc/cardreader/Kconfig"
> source "drivers/misc/uacce/Kconfig"
> source "drivers/misc/pvpanic/Kconfig"
> source "drivers/misc/mchp_pci1xxxx/Kconfig"
> +source "drivers/misc/mikrobus/Kconfig"
> endmenu
> diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> index ea6ea5bbbc9c..b9ac88055b87 100644
> --- a/drivers/misc/Makefile
> +++ b/drivers/misc/Makefile
> @@ -68,3 +68,4 @@ obj-$(CONFIG_TMR_INJECT) += xilinx_tmr_inject.o
> obj-$(CONFIG_TPS6594_ESM) += tps6594-esm.o
> obj-$(CONFIG_TPS6594_PFSM) += tps6594-pfsm.o
> obj-$(CONFIG_NSM) += nsm.o
> +obj-y += mikrobus/
> diff --git a/drivers/misc/mikrobus/Kconfig b/drivers/misc/mikrobus/Kconfig
> new file mode 100644
> index 000000000000..f0770006b4fe
> --- /dev/null
> +++ b/drivers/misc/mikrobus/Kconfig
> @@ -0,0 +1,19 @@
> +menuconfig MIKROBUS
> + tristate "Module for instantiating devices on mikroBUS ports"
> + depends on GPIOLIB
> + depends on W1
> + depends on W1_MASTER_GPIO
> + help
> + This option enables the mikroBUS driver. mikroBUS is an add-on
> + board socket standard that offers maximum expandability with
> + the smallest number of pins. The mikroBUS driver instantiates
> + devices on a mikroBUS port described by identifying data present
> + in an add-on board resident EEPROM, more details on the mikroBUS
> + driver support and discussion can be found in this eLinux wiki :
> + elinux.org/Mikrobus
> +
> +
> + Say Y here to enable support for this driver.
> +
> + To compile this code as a module, chose M here: the module
> + will be called mikrobus.ko
> diff --git a/drivers/misc/mikrobus/Makefile b/drivers/misc/mikrobus/Makefile
> new file mode 100644
> index 000000000000..c89ff2abb80e
> --- /dev/null
> +++ b/drivers/misc/mikrobus/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0
> +# mikroBUS Core
> +
> +obj-$(CONFIG_MIKROBUS) += mikrobus.o
> +mikrobus-y := mikrobus_core.o mikrobus_manifest.o
> +obj-$(CONFIG_MIKROBUS) += mikrobus_id.o
> diff --git a/drivers/misc/mikrobus/mikrobus_core.c b/drivers/misc/mikrobus/mikrobus_core.c
> new file mode 100644
> index 000000000000..17718ed315b9
> --- /dev/null
> +++ b/drivers/misc/mikrobus/mikrobus_core.c
> @@ -0,0 +1,942 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * mikroBUS driver for instantiating add-on
> + * board devices with an identifier EEPROM
> + *
> + * Copyright 2020 Vaishnav M A, BeagleBoard.org Foundation.
> + * Copyright 2024 Ayush Singh <ayushdevel1325@...il.com>
> + */
> +
> +#define pr_fmt(fmt) "mikrobus:%s: " fmt, __func__
> +
> +#include <linux/err.h>
> +#include <linux/errno.h>
> +#include <linux/idr.h>
> +#include <linux/init.h>
> +#include <linux/jump_label.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/mutex.h>
> +#include <linux/w1.h>
> +#include <linux/device.h>
> +#include <linux/i2c.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/machine.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/nvmem-provider.h>
> +#include <linux/interrupt.h>
> +#include <linux/spi/spi.h>
> +#include <linux/serdev.h>
> +#include <linux/property.h>
> +#include <linux/platform_device.h>
> +#include <linux/debugfs.h>
> +#include <linux/pinctrl/pinctrl.h>
> +#include <linux/pinctrl/pinmux.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/regulator/fixed.h>
> +#include <linux/regulator/machine.h>
> +#include <linux/clk-provider.h>
> +#include <linux/greybus/greybus_manifest.h>
> +#include <linux/of_platform.h>
> +#include <linux/pwm.h>
Order all includes by name and double check if you really need that
bunch. I have doubts. Why do you implement nvmem provider here? Why do
you include GPIO machine driver here? I could go on...
> +
> +#include "mikrobus_core.h"
> +#include "mikrobus_manifest.h"
> +
> +#define MIKROBUS_ID_EEPROM_MANIFEST_ADDR 0x20
> +
> +static DEFINE_MUTEX(core_lock);
> +static DEFINE_IDR(mikrobus_port_idr);
> +static struct class_compat *mikrobus_port_compat_class;
> +int __mikrobus_first_dynamic_bus_num;
First, don't mix local and global scope variables.
Second, no don't define global scope variables.
> +static bool is_registered;
> +static int mikrobus_port_id_eeprom_probe(struct mikrobus_port *port);
> +
> +const char *MIKROBUS_PINCTRL_STR[] = { "pwm", "uart", "i2c", "spi" };
No global scope variables.
> +
> +const struct bus_type mikrobus_bus_type = {
> + .name = "mikrobus",
> +};
> +EXPORT_SYMBOL_GPL(mikrobus_bus_type);
Why it has to be global and has to be exported?
> +
> +int mikrobus_port_scan_eeprom(struct mikrobus_port *port)
> +{
> + const u16 manifest_start_addr = MIKROBUS_ID_EEPROM_MANIFEST_ADDR;
> + struct addon_board_info *board;
> + int manifest_size, retval;
> + char header[12], *buf;
> +
> + if (port->skip_scan)
> + return -EINVAL;
> +
> + retval = nvmem_device_read(port->eeprom, manifest_start_addr, 12, header);
> + if (retval != 12) {
> + return dev_err_probe(&port->dev, -EINVAL, "failed to fetch manifest header %d\n",
> + retval);
Is it probe context? Same comment everywhere else.
> + }
> +
> + manifest_size = mikrobus_manifest_header_validate(header, 12);
> + if (manifest_size < 0) {
> + return dev_err_probe(&port->dev, -EINVAL, "invalid manifest size %d\n",
Are you sure this fits in Linux coding style limit (not checkpatch
limit, but the limit expressed by Linux coding style)?
> + manifest_size);
> + }
> +
> + buf = kzalloc(manifest_size, GFP_KERNEL);
> + if (!buf)
> + return -ENOMEM;
> +
> + retval = nvmem_device_read(port->eeprom, manifest_start_addr, manifest_size, buf);
> + if (retval != manifest_size) {
> + retval =
> + dev_err_probe(&port->dev, -EINVAL, "failed to fetch manifest %d\n", retval);
No, this for sure does not fit.
> + goto err_free_buf;
> + }
> +
> + board = kzalloc(sizeof(*board), GFP_KERNEL);
> + if (!board) {
> + retval = -ENOMEM;
> + goto err_free_buf;
> + }
> +
> + w1_reset_bus(port->w1_master);
> + /* set RST HIGH */
> + gpiod_direction_output(port->gpios->desc[MIKROBUS_PIN_RST], 1);
> + set_bit(W1_ABORT_SEARCH, &port->w1_master->flags);
> +
> + INIT_LIST_HEAD(&board->manifest_descs);
> + INIT_LIST_HEAD(&board->devices);
> + retval = mikrobus_manifest_parse(board, buf, manifest_size);
> + if (!retval) {
> + retval = dev_err_probe(&port->dev, -EINVAL, "failed to parse manifest, size %d\n",
> + manifest_size);
> + goto err_free_board;
> + }
> +
> + retval = mikrobus_board_register(port, board);
> + if (retval) {
> + dev_err(&port->dev, "failed to register board %s\n", board->name);
> + goto err_free_board;
> + }
> +
> + kfree(buf);
> + return 0;
> +
> +err_free_board:
> + kfree(board);
> +err_free_buf:
> + kfree(buf);
> + return retval;
> +}
> +EXPORT_SYMBOL_GPL(mikrobus_port_scan_eeprom);
> +
> +static ssize_t name_show(struct device *dev, struct device_attribute *attr, char *buf)
> +{
> + return sprintf(buf, "%s\n", to_mikrobus_port(dev)->name);
> +}
> +static DEVICE_ATTR_RO(name);
> +
> +static ssize_t new_device_store(struct device *dev, struct device_attribute *attr, const char *buf,
> + size_t count)
Again, does not fit to coding style wrap limit.
But what's more important: where is ABI for all your interfaces? It
seems you created user-space interface for registering devices. This
needs to be discussed first.
> +{
> + struct mikrobus_port *port = to_mikrobus_port(dev);
> + struct addon_board_info *board;
> + int retval;
> +
> + if (port->board)
> + return dev_err_probe(dev, -EBUSY, "already has board registered\n");
> +
> + board = kzalloc(sizeof(*board), GFP_KERNEL);
> + if (!board)
> + return -ENOMEM;
..
> +
> +static int mikrobus_port_probe_pinctrl_setup(struct mikrobus_port *port)
> +{
> + struct device *dev = port->dev.parent;
> + struct pinctrl_state *state;
> + int retval, i;
> +
> + state = pinctrl_lookup_state(port->pinctrl, PINCTRL_STATE_DEFAULT);
> + if (!IS_ERR(state)) {
> + retval = pinctrl_select_state(port->pinctrl, state);
> + if (retval) {
> + return dev_err_probe(dev, retval, "Failed to select state %s\n",
> + PINCTRL_STATE_DEFAULT);
> + }
> + } else {
> + return dev_err_probe(dev, PTR_ERR(state), "failed to find state %s\n",
> + PINCTRL_STATE_DEFAULT);
> + }
> +
> + for (i = 0; i < MIKROBUS_NUM_PINCTRL_STATE; i++) {
> + port->pinctrl_selected[i] = kmalloc(MIKROBUS_PINCTRL_NAME_SIZE, GFP_KERNEL);
> + sprintf(port->pinctrl_selected[i], "%s_%s", MIKROBUS_PINCTRL_STR[i],
> + PINCTRL_STATE_DEFAULT);
> + }
> +
> + retval = mikrobus_port_pinctrl_select(port);
> + if (retval)
> + dev_err(dev, "failed to select pinctrl states [%d]", retval);
> +
> + return retval;
> +}
> +
> +static int mikrobus_port_probe(struct platform_device *pdev)
> +{
> + struct device_node *i2c_adap_np, *uart_np, *spi_np;
> + struct device *dev = &pdev->dev;
> + struct mikrobus_port *port;
> + int retval;
int ret
> +
> + port = kzalloc(sizeof(*port), GFP_KERNEL);
Why not devm?
> + if (!port)
> + return -ENOMEM;
> +
> + /* I2C setup */
> + i2c_adap_np = of_parse_phandle(dev->of_node, "i2c-adapter", 0);
> + if (!i2c_adap_np) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot parse i2c-adapter");
> + goto err_port;
> + }
> + port->i2c_adap = of_find_i2c_adapter_by_node(i2c_adap_np);
> + of_node_put(i2c_adap_np);
> +
> + /* GPIO setup */
> + port->gpios = gpiod_get_array(dev, "mikrobus", GPIOD_OUT_LOW);
> + if (IS_ERR(port->gpios)) {
> + retval = PTR_ERR(port->gpios);
> + dev_err(dev, "failed to get gpio array [%d]", retval);
ret = dev_err_probe
Where is put_device? You leak I2C adapter. All code leaks probably much
more.
> + goto err_port;
> + }
> +
> + /* SPI setup */
> + spi_np = of_parse_phandle(dev->of_node, "spi-controller", 0);
> + if (!spi_np) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot parse spi-controller");
> + goto err_port;
> + }
> + port->spi_ctrl = of_find_spi_controller_by_node(spi_np);
> + of_node_put(spi_np);
> + if (!port->spi_ctrl) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot find spi controller");
> + goto err_port;
> + }
> + retval = device_property_read_u32_array(dev, "spi-cs", port->chip_select, MIKROBUS_NUM_CS);
> + if (retval) {
> + dev_err(dev, "failed to get spi-cs [%d]", retval);
> + goto err_port;
> + }
> +
> + /* UART setup */
> + uart_np = of_parse_phandle(dev->of_node, "uart", 0);
> + if (!uart_np) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot parse uart");
> + goto err_port;
> + }
> + port->ser_ctrl = of_find_serdev_controller_by_node(uart_np);
> + of_node_put(uart_np);
> + if (!port->ser_ctrl) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot find uart controller");
> + goto err_port;
> + }
> +
> + /* PWM setup */
> + port->pwm = devm_pwm_get(dev, NULL);
> + if (!port->pwm) {
> + retval = dev_err_probe(dev, -ENODEV, "cannot find pwm controller");
> + goto err_port;
> + }
> +
> + /* pinctrl setup */
> + port->pinctrl = devm_pinctrl_get(dev);
> + if (IS_ERR(port->pinctrl)) {
> + retval = PTR_ERR(port->pinctrl);
> + dev_err(dev, "failed to get pinctrl [%d]", retval);
ret = dev_err_probe()
> + goto err_port;
> + }
> + port->dev.parent = dev;
> + port->dev.of_node = pdev->dev.of_node;
> + retval = mikrobus_port_probe_pinctrl_setup(port);
> + if (retval) {
> + dev_err(dev, "failed to setup pinctrl [%d]", retval);
> + goto err_port;
> + }
> +
> + retval = mikrobus_port_register(port);
> + if (retval) {
> + dev_err(dev, "port : can't register port [%d]", retval);
> + goto err_port;
> + }
> +
> + platform_set_drvdata(pdev, port);
> +
> + return 0;
> +
> +err_port:
> + kfree(port);
> + return retval;
> +}
> +
> +static int mikrobus_port_remove(struct platform_device *pdev)
> +{
> + struct mikrobus_port *port = platform_get_drvdata(pdev);
> +
> + mikrobus_port_delete(port);
> + return 0;
> +}
> +
> +static const struct of_device_id mikrobus_port_of_match[] = {
> + { .compatible = "mikrobus-connector" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, mikrobus_port_of_match);
> +
> +static struct platform_driver mikrobus_port_driver = {
> + .probe = mikrobus_port_probe,
> + .remove = mikrobus_port_remove,
> + .driver = {
> + .name = "mikrobus",
> + .of_match_table = of_match_ptr(mikrobus_port_of_match),
Drop of_match_ptr
> + },
> +};
> +
> +static int mikrobus_init(void)
> +{
> + int retval;
> +
> + retval = bus_register(&mikrobus_bus_type);
> + if (retval) {
> + pr_err("bus_register failed (%d)\n", retval);
> + return retval;
> + }
> +
> + mikrobus_port_compat_class = class_compat_register("mikrobus-port");
> + if (!mikrobus_port_compat_class) {
> + pr_err("class_compat register failed (%d)\n", retval);
> + retval = -ENOMEM;
> + goto class_err;
> + }
> +
> + retval = of_alias_get_highest_id("mikrobus");
> + if (retval >= __mikrobus_first_dynamic_bus_num)
> + __mikrobus_first_dynamic_bus_num = retval + 1;
> +
> + is_registered = true;
> + retval = platform_driver_register(&mikrobus_port_driver);
> + if (retval)
> + pr_err("driver register failed [%d]\n", retval);
> +
> + return retval;
> +
> +class_err:
> + bus_unregister(&mikrobus_bus_type);
> + idr_destroy(&mikrobus_port_idr);
> + is_registered = false;
> + return retval;
> +}
> +subsys_initcall(mikrobus_init);
> +
> +static void mikrobus_exit(void)
> +{
> + platform_driver_unregister(&mikrobus_port_driver);
> + bus_unregister(&mikrobus_bus_type);
> + class_compat_unregister(mikrobus_port_compat_class);
> + idr_destroy(&mikrobus_port_idr);
> +}
> +module_exit(mikrobus_exit);
> +
> +MODULE_AUTHOR("Vaishnav M A <vaishnav@...gleboard.org>");
> +MODULE_AUTHOR("Ayush Singh <ayushdevel1325@...gleboard.org>");
> +MODULE_DESCRIPTION("mikroBUS main module");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/misc/mikrobus/mikrobus_core.h b/drivers/misc/mikrobus/mikrobus_core.h
> new file mode 100644
> index 000000000000..8bd101828964
> --- /dev/null
> +++ b/drivers/misc/mikrobus/mikrobus_core.h
> @@ -0,0 +1,201 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * mikroBUS Driver for instantiating add-on
> + * board devices with an identifier EEPROM
> + *
> + * Copyright 2020 Vaishnav M A, BeagleBoard.org Foundation.
> + */
> +
> +#ifndef __MIKROBUS_H
> +#define __MIKROBUS_H
> +
> +#include <linux/kernel.h>
> +#include <linux/device.h>
> +#include <linux/i2c.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/gpio/machine.h>
> +#include <linux/spi/spi.h>
> +#include <linux/serdev.h>
> +#include <linux/property.h>
> +#include <linux/pinctrl/pinctrl.h>
> +#include <linux/pinctrl/pinmux.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/nvmem-provider.h>
Why did you stuff here so many includes? Are you sure you need all three
pinctrls? All three gpio? The header must include *only* stuff it
directly uses.
> +
> +#define MIKROBUS_VERSION_MAJOR 0x00
> +#define MIKROBUS_VERSION_MINOR 0x03
> +
> +#define MIKROBUS_NAME_SIZE 40
> +#define MIKROBUS_PINCTRL_NAME_SIZE 20
> +
> +#define MIKROBUS_NUM_PINCTRL_STATE 4
> +#define MIKROBUS_NUM_CS 2
> +
> +#define MIKROBUS_PINCTRL_PWM 0
> +#define MIKROBUS_PINCTRL_UART 1
> +#define MIKROBUS_PINCTRL_I2C 2
> +#define MIKROBUS_PINCTRL_SPI 3
> +
> +#define MIKROBUS_PINCTRL_STATE_GPIO "gpio"
> +
> +#define MIKROBUS_EEPROM_EXIT_ID_CMD 0xD2
> +
> +extern const struct bus_type mikrobus_bus_type;
> +extern const struct device_type mikrobus_port_type;
> +extern const char *MIKROBUS_PINCTRL_STR[];
All three look suspicious. Why do you create global variables? Looks
like some pattern from very old vendor code...
> +
> +enum mikrobus_property_type {
> + MIKROBUS_PROPERTY_TYPE_MIKROBUS = 0x00,
> + MIKROBUS_PROPERTY_TYPE_PROPERTY = 0x01,
> + MIKROBUS_PROPERTY_TYPE_GPIO = 0x02,
> + MIKROBUS_PROPERTY_TYPE_U8 = 0x03,
> + MIKROBUS_PROPERTY_TYPE_U16 = 0x04,
> + MIKROBUS_PROPERTY_TYPE_U32 = 0x05,
> + MIKROBUS_PROPERTY_TYPE_U64 = 0x06,
> + MIKROBUS_PROPERTY_TYPE_REGULATOR = 0x07,
> + MIKROBUS_PROPERTY_TYPE_CLOCK = 0x08,
> +};
> +
> +enum mikrobus_pin {
> + MIKROBUS_PIN_PWM = 0x00,
> + MIKROBUS_PIN_INT = 0x01,
> + MIKROBUS_PIN_RX = 0x02,
> + MIKROBUS_PIN_TX = 0x03,
> + MIKROBUS_PIN_SCL = 0x04,
> + MIKROBUS_PIN_SDA = 0x05,
> + MIKROBUS_PIN_MOSI = 0x06,
> + MIKROBUS_PIN_MISO = 0x07,
> + MIKROBUS_PIN_SCK = 0x08,
> + MIKROBUS_PIN_CS = 0x09,
> + MIKROBUS_PIN_RST = 0x0A,
> + MIKROBUS_PIN_AN = 0x0B,
> + MIKROBUS_PORT_PIN_COUNT = 0x0C,
Why do you need to assign values to the enumerated entries?
> +};
> +
> +enum mikrobus_pin_state {
> + MIKROBUS_STATE_INPUT = 0x01,
> + MIKROBUS_STATE_OUTPUT_HIGH = 0x02,
> + MIKROBUS_STATE_OUTPUT_LOW = 0x03,
> + MIKROBUS_STATE_PWM = 0x04,
> + MIKROBUS_STATE_SPI = 0x05,
> + MIKROBUS_STATE_I2C = 0x06,
> + MIKROBUS_STATE_UART = 0x07,
> +};
> +
> +/*
> + * board_device_info describes a single device on a mikrobus add-on
> + * board, an add-on board can present one or more device to the host
> + *
> + * @gpio_lookup: used to provide the GPIO lookup table for
> + * passing the named GPIOs to device drivers.
> + * @properties: used to provide the property_entry to pass named
> + * properties to device drivers, applicable only when driver uses
> + * device_property_read_* calls to fetch the properties.
> + * @num_gpio_resources: number of named gpio resources for the device,
> + * used mainly for gpiod_lookup_table memory allocation.
> + * @num_properties: number of custom properties for the device,
> + * used mainly for property_entry memory allocation.
> + * @protocol: used to know the type of the device and it should
> + * contain one of the values defined under 'enum greybus_class_type'
> + * under linux/greybus/greybus_manifest.h
> + * @reg: I2C address for the device, for devices on the SPI bus
> + * this field is the chip select address relative to the mikrobus
> + * port:0->device chip select connected to CS pin on mikroBUS port
> + * 1->device chip select connected to RST Pin on mikroBUS port
> + * @mode: SPI mode
> + * @max_speed_hz: SPI max speed(Hz)
> + * @drv_name: device_id to match with the driver
> + * @irq_type: type of IRQ trigger , match with defines in linux/interrupt.h
> + * @irq: irq number relative to the mikrobus port should contain one of the
> + * values defined under 'enum mikrobus_pin'
> + * @id: device id starting from 1
> + */
> +struct board_device_info {
> + struct gpiod_lookup_table *gpio_lookup;
> + struct property_entry *properties;
> + struct property_entry *regulators;
> + struct property_entry *clocks;
> + struct list_head links;
> + unsigned short num_gpio_resources;
> + unsigned short num_properties;
> + unsigned short num_regulators;
> + unsigned short num_clocks;
> + unsigned short protocol;
> + unsigned short reg;
> + unsigned int mode;
> + void *dev_client;
> + u32 max_speed_hz;
> + char *drv_name;
> + int irq_type;
> + int irq;
> + int id;
> +};
> +
> +/*
> + * addon_board_info describes a mikrobus add-on device the add-on
> + * board, an add-on board can present one or more device to the host
> + *
> + * @manifest_descs: list of manifest descriptors
> + * @devices: list of devices on the board
> + * @pin_state: the state of each pin on the mikrobus port required
> + * for the add-on board should contain one of the values defined under
> + * 'enum mikrobus_pin_state' restrictions are as per mikrobus standard
> + * specifications.
> + * @name: add-on board name
> + */
> +struct addon_board_info {
> + struct list_head manifest_descs;
> + struct list_head devices;
> + u8 pin_state[MIKROBUS_PORT_PIN_COUNT];
> + char *name;
> +};
> +
> +/*
> + * mikrobus_port describes the peripherals mapped to a
> + * mikrobus port.
> + *
> + * @eeprom_client: i2c_client corresponding to the eeprom
> + * on the add-on board.
> + * @board: pointer to the attached add-on board.
> + * @i2c_adap: I2C adapter attached to the mikrobus port.
> + * @spi_mstr: SPI master attached to the mikrobus port.
> + * @eeprom: nvmem_device for the eeprom on the add-on board.
> + * @pwm: pwm_device attached to the mikrobus port PWM pin.
> + * @pinctrl_selected: current pinctrl_selected state.
> + * @chip_select: chip select number mapped to the SPI
> + * CS pin on the mikrobus port and the RST pin on the mikrobus
> + * port
> + * @id: port id starting from 1
> + */
> +struct mikrobus_port {
> + struct addon_board_info *board;
> + struct nvmem_device *eeprom;
> + struct i2c_adapter *i2c_adap;
> + struct spi_controller *spi_ctrl;
> + struct w1_master *w1_master;
> + struct platform_device *w1_gpio;
> + struct serdev_controller *ser_ctrl;
> + struct gpio_descs *gpios;
> + struct pwm_device *pwm;
> + struct pinctrl *pinctrl;
> + struct module *owner;
> + struct device dev;
> + char name[MIKROBUS_NAME_SIZE];
Why do you have fixed size names?
> + char *pinctrl_selected[MIKROBUS_NUM_PINCTRL_STATE];
> + unsigned int chip_select[MIKROBUS_NUM_CS];
> + int skip_scan;
> + int id;
> +};
> +
> +#define to_mikrobus_port(d) container_of(d, struct mikrobus_port, dev)
> +
> +void mikrobus_board_unregister(struct mikrobus_port *port, struct addon_board_info *board);
> +int mikrobus_board_register(struct mikrobus_port *port, struct addon_board_info *board);
> +int mikrobus_port_register(struct mikrobus_port *port);
> +int mikrobus_port_pinctrl_select(struct mikrobus_port *port);
> +void mikrobus_port_delete(struct mikrobus_port *port);
> +int mikrobus_port_scan_eeprom(struct mikrobus_port *port);
> +struct mikrobus_port *mikrobus_find_port_by_w1_master(struct w1_master *master);
> +#endif /* __MIKROBUS_H */
> diff --git a/drivers/misc/mikrobus/mikrobus_id.c b/drivers/misc/mikrobus/mikrobus_id.c
> new file mode 100644
> index 000000000000..42a0a558785d
> --- /dev/null
> +++ b/drivers/misc/mikrobus/mikrobus_id.c
> @@ -0,0 +1,229 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * mikrobus_id.c - w1 mikroBUS ID family EEPROM driver
> + *
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/device.h>
> +#include <linux/types.h>
> +#include <linux/delay.h>
> +
> +#include <linux/crc16.h>
> +#include <linux/w1.h>
> +#include <linux/nvmem-provider.h>
> +
> +#include "mikrobus_core.h"
> +
> +#define W1_EEPROM_MIKROBUS_ID 0xCC
> +#define W1_MIKROBUS_ID_EEPROM_SIZE 0x0200
> +#define W1_MIKROBUS_ID_EEPROM_PAGE_SIZE 32
> +#define W1_MIKROBUS_ID_READ_EEPROM 0x69
> +#define W1_MIKROBUS_ID_WRITE_EEPROM 0x96
> +#define W1_MIKROBUS_ID_RELEASE_EEPROM 0xAA
> +#define W1_MIKROBUS_ID_EEPROM_READ_RETRIES 10
> +
> +#define W1_MIKROBUS_EEPROM_MANIFEST_START_PAGE 1
> +
> +static ssize_t mikrobus_manifest_store(struct device *device, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + u8 write_request[] = { W1_MIKROBUS_ID_WRITE_EEPROM,
> + W1_MIKROBUS_EEPROM_MANIFEST_START_PAGE };
> + u8 release_command = W1_MIKROBUS_ID_RELEASE_EEPROM;
> + struct w1_slave *sl = dev_to_w1_slave(device);
This looks like w1 driver. Why is it not suitable for w1 directory?
Best regards,
Krzysztof
Powered by blists - more mailing lists