lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Date: Wed, 20 Mar 2024 23:45:30 +0300
From: Arınç ÜNAL via B4 Relay <devnull+arinc.unal.arinc9.com@...nel.org>
To: Daniel Golle <daniel@...rotopia.org>, DENG Qingfang <dqfext@...il.com>, 
 Sean Wang <sean.wang@...iatek.com>, Andrew Lunn <andrew@...n.ch>, 
 Florian Fainelli <f.fainelli@...il.com>, 
 Vladimir Oltean <olteanv@...il.com>, 
 "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, 
 Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, 
 Matthias Brugger <matthias.bgg@...il.com>, 
 AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>, 
 Landen Chao <Landen.Chao@...iatek.com>
Cc: Bartel Eerdekens <bartel.eerdekens@...stell8.be>, 
 mithat.guner@...ont.com, erkin.bozoglu@...ont.com, netdev@...r.kernel.org, 
 linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org, 
 linux-mediatek@...ts.infradead.org, 
 Arınç ÜNAL <arinc.unal@...nc9.com>
Subject: [PATCH net] net: dsa: mt7530: fix improper frames on all 25MHz and
 40MHz XTAL MT7530

From: Arınç ÜNAL <arinc.unal@...nc9.com>

The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.

The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.

Introduce a check to run it only on MT7530 with 40MHz XTAL.

The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.

When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.

When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.

For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.

Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.

With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.

Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/4a5dd143f2172ec97a2872fa29c7c4cd520f45b5/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c#L1039
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
---
 drivers/net/dsa/mt7530.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 6986f538a4d0..c856a13bc2f1 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2232,8 +2232,6 @@ mt7530_setup(struct dsa_switch *ds)
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
 		     SYS_CTRL_REG_RST);
 
-	mt7530_pll_setup(priv);
-
 	/* Lower Tx driving for TRGMII path */
 	for (i = 0; i < NUM_TRGMII_CTRL; i++)
 		mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
@@ -2249,6 +2247,9 @@ mt7530_setup(struct dsa_switch *ds)
 	val |= MHWTRAP_MANUAL;
 	mt7530_write(priv, MT7530_MHWTRAP, val);
 
+	if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_40MHZ)
+		mt7530_pll_setup(priv);
+
 	mt753x_trap_frames(priv);
 
 	/* Enable and reset MIB counters */

---
base-commit: 9c6a59543a3965071d65b0f9ea43aa396ce2ed14
change-id: 20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-e2aaed550ed5

Best regards,
-- 
Arınç ÜNAL <arinc.unal@...nc9.com>



Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ