Message-Id: <20240321-cn9130-som-v1-2-711127a409ae@solid-run.com>
Date: Thu, 21 Mar 2024 22:47:12 +0100
From: Josua Mayer <josua@...id-run.com>
To: Andrew Lunn <andrew@...n.ch>, 
 Gregory Clement <gregory.clement@...tlin.com>, 
 Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>, 
 Rob Herring <robh+dt@...nel.org>, 
 Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, 
 Conor Dooley <conor+dt@...nel.org>
Cc: Yazan Shhady <yazan.shhady@...id-run.com>, 
 linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org, 
 linux-kernel@...r.kernel.org, Josua Mayer <josua@...id-run.com>
Subject: [PATCH 2/2] arm64: dts: add description for solidrun cn9130 som
 and clearfog boards

Add description for the SolidRun CN9130 SoM, and Clearfog Base / Pro
reference boards.

The SoM has been designed as a pin-compatible replacement for the older
Armada 388 based SoM. Therefore it supports the same boards and a
similar feature set.

Most notable upgrades:
- 4x Cortex-A72
- 10Gbps SFP
- Both eMMC and SD supported at the same time

The developer first supporting this product at SolidRun decided to use
different filenames for the DTBs: Armada 388 uses the full
"clearfog" string while cn9130 uses the abbreviation "cf".
This name is already hard-coded in pre-installed vendor u-boot and can
not be changed easily.

NOTICE IN CASE ANYBODY WANTS TO SELF-UPGRADE:
CN9130 SoM has a different footprint from Armada 388 SoM.
Components on the carrier board below the SoM may collide causing
damage, such as on Clearfog Base.

Signed-off-by: Josua Mayer <josua@...id-run.com>
---
 arch/arm64/boot/dts/marvell/Makefile           |   2 +
 arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 138 ++++++++++++++
 arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts  | 249 +++++++++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9130-cf.dtsi     | 198 ++++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi | 160 ++++++++++++++++
 5 files changed, 747 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 99b8cb3c49e1..019f2251d696 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -28,3 +28,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
new file mode 100644
index 000000000000..b0067940d5e4
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@...id-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Base.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+	model = "SolidRun CN9130 Clearfog Base";
+	compatible = "solidrun,clearfog-base-a1", "solidrun,clearfog-a1",
+		     "solidrun,cn9130-sr-som","marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&rear_button_pins>;
+		pinctrl-names = "default";
+
+		button-0 {
+			/* The rear SW3 button */
+			label = "Rear Button";
+			gpios = <&cp0_gpio1 31 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_0>;
+		};
+	};
+
+	rfkill-m2-gnss {
+		compatible = "rfkill-gpio";
+		label = "m.2 GNSS";
+		radio-type = "gps";
+		/* rfkill-gpio inverts internally */
+		shutdown-gpios = <&expander0 9 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* M.2 is B-keyed, so w-disable is for WWAN */
+	rfkill-m2-wwan {
+		compatible = "rfkill-gpio";
+		label = "m.2 WWAN";
+		radio-type = "wwan";
+		/* rfkill-gpio inverts internally */
+		shutdown-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp0_eth1 {
+	phy = <&phy1>;
+	phys = <&cp0_comphy3 1>;
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&cp0_eth2_phy {
+	/*
+	 * Configure LEDs:
+	 * - LED[0]: link/activity: On/blink (green)
+	 * - LED[1]: link is 100/1000Mbps: On (yellow)
+	 * - LED[2]: high impedance (floating)
+	 */
+	marvell,reg-init = <3 16 0xf000 0x0a61>;
+};
+
+&cp0_gpio1 {
+	sim-select-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sim-select";
+	};
+};
+
+&cp0_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		/*
+		 * Configure LEDs:
+		 * - LED[0]: link/activity: On/blink (green)
+		 * - LED[1]: link is 100/1000Mbps: On (yellow)
+		 * - LED[2]: high impedance (floating)
+		 *
+		 * Polarity: On = low, Off = high (not hi-z)
+		 */
+		marvell,reg-init = <3 16 0xf000 0x0a61>,
+				   <3 17 0x003f 0x000a>;
+	};
+};
+
+&cp0_pinctrl {
+	pinctrl-0 = <&sim_select_pins>;
+	pintrl-names = "default";
+
+	rear_button_pins: cp0-rear-button-pins {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+
+	sim_select_pins: cp0-sim-select-pins {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+};
+
+/*
+ * SRDS #4 - USB 3.0 host on M.2 connector
+ * USB-2.0 Host on Type-A connector
+ */
+&cp0_usb3_1 {
+	phys = <&cp0_comphy4 1>, <&cp0_utmi1>;
+	phy-names = "comphy", "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&expander0 {
+	m2-full-card-power-off-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "m2-full-card-power-off";
+	};
+
+	m2-reset-hog {
+		gpio-hog;
+		gpios = <10 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "m2-reset";
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
new file mode 100644
index 000000000000..f7733f6a89b8
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@...id-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Pro.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+	model = "SolidRun CN9130 Clearfog Pro";
+	compatible = "solidrun,clearfog-pro-a1", "solidrun,clearfog-a1",
+		     "solidrun,cn9130-sr-som","marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&rear_button_pins>;
+		pinctrl-names = "default";
+
+		button-0 {
+			/* The rear SW3 button */
+			label = "Rear Button";
+			gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_0>;
+		};
+	};
+
+	/* mini-pcie w-disable could be either wlan or wwan */
+	rfkill-mpcie1-xxan {
+		compatible = "rfkill-gpio";
+		label = "mPCI-e WLAN (CON2)";
+		radio-type = "wlan";
+		/* rfkill-gpio inverts internally */
+		shutdown-gpios = <&expander0 7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* SRDS #3 - SGMII 1GE to L2 switch */
+&cp0_eth1 {
+	phys = <&cp0_comphy3 1>;
+	phy-mode = "sgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&cp0_eth2_phy {
+	/*
+	 * Configure LEDs similar to switch ports:
+	 * - LED[0]: link/activity: On/blink (green)
+	 * - LED[1]: link is 100/1000Mbps: On (red)
+	 * - LED[2]: high impedance (floating)
+	 *
+	 * Switch port defaults:
+	 * - LED0: link/activity: On/blink (green)
+	 * - LED1: link is 1000Mbps: On (red)
+	 *
+	 * Identical configuration is impossible.
+	 */
+	marvell,reg-init = <3 16 0xf000 0x0a61>;
+};
+
+&cp0_mdio {
+	ethernet-switch@4 {
+		compatible = "marvell,mv88e6085";
+		reg = <4>;
+		pinctrl-0 = <&dsa_clk_pins &dsa_pins>;
+		pinctrl-names = "default";
+		reset-gpios = <&cp0_gpio1 27 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&cp0_gpio1>;
+		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet-port@0 {
+				reg = <0>;
+				label = "lan5";
+				phy = <&switch0phy0>;
+			};
+
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan4";
+				phy = <&switch0phy1>;
+			};
+
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan3";
+				phy = <&switch0phy2>;
+			};
+
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan2";
+				phy = <&switch0phy3>;
+			};
+
+			ethernet-port@4 {
+				reg = <4>;
+				label = "lan1";
+				phy = <&switch0phy4>;
+			};
+
+			ethernet-port@5 {
+				reg = <5>;
+				ethernet = <&cp0_eth1>;
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet-port@6 {
+				reg = <6>;
+				label = "lan6";
+				phy-mode = "rgmii";
+
+				/*
+				 * Because of mdio address conflict the
+				 * external phy is not readable.
+				 * Force a fixed link instead.
+				 */
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: ethernet-phy@0 {
+				reg = <0x0>;
+			};
+
+			switch0phy1: ethernet-phy@1 {
+				reg = <0x1>;
+				/*
+				 * Indirectly configure LEDs for port
+				 * lan6 using external phy.
+				 * Internal PHYs are not using page 3,
+				 * therefore writing to it is safe.
+				 */
+				marvell,reg-init = <3 16 0xf000 0x0a61>;
+			};
+
+			switch0phy2: ethernet-phy@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy3: ethernet-phy@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy4: ethernet-phy@4 {
+				reg = <0x4>;
+			};
+		};
+
+		/*
+		 * There is an external phy on the switch mdio bus.
+		 * Because its mdio address collides with internal phys,
+		 * it is not readable.
+		 *
+		 * mdio-external {
+		 *	compatible = "marvell,mv88e6xxx-mdio-external";
+		 *	#address-cells = <1>;
+		 *	#size-cells = <0>;
+		 *
+		 *	ethernet-phy@1 {
+		 *		reg = <0x1>;
+		 *	};
+		 * };
+		 */
+	};
+};
+
+/* SRDS #4 - miniPCIe (CON2) */
+&cp0_pcie1 {
+	num-lanes = <1>;
+	phys = <&cp0_comphy4 1>;
+	/* dw-pcie inverts internally */
+	reset-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&cp0_pinctrl {
+	dsa_clk_pins: cp0-dsa-clk-pins {
+		marvell,pins = "mpp40";
+		marvell,function = "synce1";
+	};
+
+	dsa_pins: cp0-dsa-pins {
+		marvell,pins = "mpp27", "mpp29";
+		marvell,function = "gpio";
+	};
+
+	rear_button_pins: cp0-rear-button-pins {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+};
+
+/*
+ * USB-2.0 Host on Type-A connector
+ */
+&cp0_usb3_1 {
+	phys = <&cp0_utmi1>;
+	phy-names = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&expander0 {
+	/* CON2 */
+	pcie1-0-clkreq-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "pcie1.0-clkreq";
+	};
+
+	/* CON2 */
+	pcie1-0-w-disable-hog {
+		gpio-hog;
+		gpios = <7 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "pcie1.0-w-disable";
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
new file mode 100644
index 000000000000..1aaa0d916e75
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@...id-run.com>
+ *
+ * DTS for common base of SolidRun CN9130 Clearfog Base and Pro.
+ *
+ */
+
+/ {
+	model = "SolidRun CN9130 Clearfog";
+	compatible = "solidrun,clearfog-a1",
+		     "solidrun,cn9130-sr-som","marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	aliases {
+		i2c1 = &cp0_i2c1;
+		mmc1 = &cp0_sdhci0;
+	};
+
+	reg_usb3_vbus0: regulator-usb3-vbus0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&expander0 6 GPIO_ACTIVE_LOW>;
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c1>;
+		los-gpios = <&expander0 12 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&expander0 15 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&expander0 14 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&expander0 13 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <2000>;
+	};
+};
+
+/* SRDS #2 - SFP+ 10GE */
+&cp0_eth0 {
+	managed = "in-band-status";
+	phys = <&cp0_comphy2 0>;
+	phy-mode = "10gbase-r";
+	sfp = <&sfp>;
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	expander0: gpio-expander@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-0 = <&expander0_pins>;
+		pinctrl-names = "default";
+		interrupt-parent = <&cp0_gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+		/* CON3 */
+		pcie2-0-clkreq-hog {
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_LOW>;
+			input;
+			line-name = "pcie2.0-clkreq";
+		};
+
+		/* CON3 */
+		pcie2-0-w-disable-hog {
+			gpio-hog;
+			gpios = <3 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "pcie2.0-w-disable";
+		};
+
+		usb3-ilimit-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_LOW>;
+			input;
+			line-name = "usb3-current-limit";
+		};
+
+		m2-devslp-hog {
+			gpio-hog;
+			gpios = <11 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "m.2 devslp";
+		};
+	};
+
+	/* The MCP3021 supports standard and fast modes */
+	adc@4c {
+		compatible = "microchip,mcp3021";
+		reg = <0x4c>;
+	};
+
+	carrier_eeprom: eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <8>;
+	};
+};
+
+&cp0_i2c1 {
+	/*
+	 * Routed to SFP, M.2, mikrobus, and miniPCIe
+	 * SFP limits this to 100kHz, and requires an AT24C01A/02/04 with
+	 *  address pins tied low, which takes addresses 0x50 and 0x51.
+	 * Mikrobus doesn't specify beyond an I2C bus being present.
+	 * PCIe uses ARP to assign addresses, or 0x63-0x64.
+	 */
+	clock-frequency = <100000>;
+	pinctrl-0 = <&cp0_i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* SRDS #5 - miniPCIe (CON3) */
+&cp0_pcie2 {
+	num-lanes = <1>;
+	phys = <&cp0_comphy5 2>;
+	/* dw-pcie inverts internally */
+	reset-gpios = <&expander0 1 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&cp0_pinctrl {
+	cp0_i2c1_pins: cp0-i2c1-pins {
+		marvell,pins = "mpp35", "mpp36";
+		marvell,function = "i2c1";
+	};
+
+	cp0_mmc0_pins: cp0-mmc0-pins {
+		marvell,pins = "mpp43", "mpp56", "mpp57", "mpp58",
+			       "mpp59", "mpp60", "mpp61";
+		marvell,function = "sdio";
+	};
+
+	mikro_spi_pins: cp0-spi1-cs1-pins {
+		marvell,pins = "mpp12";
+		marvell,function = "spi1";
+	};
+
+	mikro_uart_pins: cp0-uart-pins {
+		marvell,pins = "mpp2", "mpp3";
+		marvell,function = "uart1";
+	};
+
+	expander0_pins: cp0-expander0-pins {
+		marvell,pins = "mpp4";
+		marvell,function = "gpio";
+	};
+};
+
+/* SRDS #0 - SATA on M.2 connector */
+&cp0_sata0 {
+	phys = <&cp0_comphy0 1>;
+	status = "okay";
+
+	/* only port 1 is available */
+	/delete-node/ sata-port@0;
+};
+
+/* microSD */
+&cp0_sdhci0 {
+	pinctrl-0 = <&cp0_mmc0_pins>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&cp0_spi1 {
+	/* CS1 for mikrobus */
+	pinctrl-0 = <&cp0_spi1_pins &mikro_spi_pins>;
+};
+
+/*
+ * SRDS #1 - 3.0 Host on Type-A connector
+ * USB-2.0 Host on mPCI-e connector (CON3)
+ */
+&cp0_usb3_0 {
+	phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+	phy-names = "comphy", "utmi";
+	vbus-supply = <&reg_usb3_vbus0>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&cp0_utmi {
+	status = "okay";
+};
+
+/* mikrobus uart */
+&cp0_uart0 {
+	pinctrl-0 = <&mikro_uart_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
new file mode 100644
index 000000000000..f151a2a399c1
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@...id-run.com>
+ *
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "SolidRun CN9130 SoM";
+	compatible = "solidrun,cn9130-sr-som", "marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	aliases {
+		/* label nics like armada-388 som */
+		ethernet0 = &cp0_eth2;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth0;
+		i2c0 = &cp0_i2c0;
+		mmc0 = &ap_sdhci0;
+		rtc0 = &cp0_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	v_1_8: regulator-1-8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	/* requires assembly of R9307 */
+	vhv: regulator-vhv-1-8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vhv-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		pinctrl-0 = <&cp0_reg_vhv_pins>;
+		pinctrl-names = "default";
+		gpio = <&cp0_gpio2 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ap_pinctrl {
+	ap_mmc0_pins: ap-mmc0-pins {
+		marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", "mpp4", "mpp5",
+					   "mpp6", "mpp7", "mpp8", "mpp9", "mpp10", "mpp12";
+		marvell,function = "sdio";
+		/*
+		 * mpp12 is emmc reset, function should be sdio (hw_rst),
+		 * but pinctrl-mvebu does not support this.
+		 *
+		 * From pinctrl-mvebu.h:
+		 * "The name will be used to switch to this setting in DT description, e.g.
+		 * marvell,function = "uart2". subname is only for debugging purposes."
+		 */
+	};
+};
+
+&ap_sdhci0 {
+	bus-width = <8>;
+	pinctrl-0 = <&ap_mmc0_pins>;
+	pinctrl-names = "default";
+	vqmmc-supply = <&v_1_8>;
+	status = "okay";
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* for assembly with phy */
+&cp0_eth2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_eth2_pins>;
+	phy-mode = "rgmii-id";
+	phy = <&cp0_eth2_phy>;
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	som_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <8>;
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+	pinctrl-0 = <&cp0_mdio_pins>;
+
+	/* assembly option */
+	cp0_eth2_phy: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&cp0_spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi1_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp0_eth2_pins: cp0-ge2-rgmii-pins {
+			marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47",
+				       "mpp48", "mpp49", "mpp50", "mpp51",
+				       "mpp52", "mpp53", "mpp54", "mpp55";
+			/* docs call it "ge2", but cp110-pinctrl "ge1" */
+			marvell,function = "ge1";
+		};
+
+		cp0_i2c0_pins: cp0-i2c0-pins {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+
+		cp0_mdio_pins: cp0-mdio-pins {
+			marvell,pins = "mpp40", "mpp41";
+			marvell,function = "ge";
+		};
+
+		cp0_spi1_pins: cp0-spi1-pins {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+
+		cp0_reg_vhv_pins: cp0-reg-vhv-pins {
+			marvell,pins = "mpp41";
+			marvell,function = "gpio";
+		};
+	};
+};
+
+/* AP default console */
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};

-- 
2.35.3

Powered by blists - more mailing lists