Message-ID: <20240329133458.323041-3-valla.francesco@gmail.com>
Date: Fri, 29 Mar 2024 14:34:41 +0100
From: Francesco Valla <valla.francesco@...il.com>
To: Oliver Hartkopp <socketcan@...tkopp.net>,
	Marc Kleine-Budde <mkl@...gutronix.de>,
	linux-can@...r.kernel.org
Cc: netdev@...r.kernel.org,
	linux-kernel@...r.kernel.org,
	Simon Horman <horms@...nel.org>,
	Bagas Sanjaya <bagasdotme@...il.com>,
	fabio@...aril.me,
	Francesco Valla <valla.francesco@...il.com>
Subject: [PATCH v2 1/1] Documentation: networking: document ISO 15765-2:2016

Document basic concepts, APIs and behaviour of the ISO 15675-2:2016
(ISO-TP) CAN stack.

Signed-off-by: Francesco Valla <valla.francesco@...il.com>
---
 Documentation/networking/index.rst      |   1 +
 Documentation/networking/iso15765-2.rst | 356 ++++++++++++++++++++++++
 MAINTAINERS                             |   1 +
 3 files changed, 358 insertions(+)
 create mode 100644 Documentation/networking/iso15765-2.rst

diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst
index 473d72c36d61..bbd9bf537793 100644
--- a/Documentation/networking/index.rst
+++ b/Documentation/networking/index.rst
@@ -19,6 +19,7 @@ Contents:
    caif/index
    ethtool-netlink
    ieee802154
+   iso15765-2
    j1939
    kapi
    msg_zerocopy
diff --git a/Documentation/networking/iso15765-2.rst b/Documentation/networking/iso15765-2.rst
new file mode 100644
index 000000000000..bbed4d2ef1a8
--- /dev/null
+++ b/Documentation/networking/iso15765-2.rst
@@ -0,0 +1,356 @@
+.. SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+
+=========================
+ISO 15765-2:2016 (ISO-TP)
+=========================
+
+Overview
+========
+
+ISO 15765-2:2016, also known as ISO-TP, is a transport protocol specifically
+defined for diagnostic communication on CAN. It is widely used in the automotive
+industry, for example as the transport protocol for UDSonCAN (ISO 14229-3) or
+emission-related diagnostic services (ISO 15031-5).
+
+ISO-TP can be used both on CAN CC (aka Classical CAN, CAN 2.0B) and CAN FD (CAN
+with Flexible Datarate) based networks. It is also designed to be compatible
+with a CAN network using SAE J1939 as data link layer (however, this is not a
+requirement).
+
+Specifications used
+-------------------
+
+* ISO 15765-2:2016 : Road vehicles - Diagnostic communication over Controller
+  Area Network (DoCAN). Part 2: Transport protocol and network layer services.
+
+Addressing
+----------
+
+In its simplest form, ISO-TP is based on two kinds of addressing modes for the
+nodes connected to the same network:
+
+- physical addressing is implemented by two node-specific addresses (CAN
+  identifiers) and is used in 1-to-1 communication
+- functional addressing is implemented by one node-specific address (CAN
+  identifier) and is used in 1-to-N communication
+
+In a so-called "normal" addressing scenario, both these addresses are
+represented by a 29-bit CAN ID. However, in order to support larger networks,
+an "extended" addressing scheme can be adopted: in this case, the first byte of
+the data payload is used as an additional component of the address (both for
+the physical and functional cases); two different CAN IDs are still required.
+
+Transport protocol and associated frame types
+---------------------------------------------
+
+When transmitting data using the ISO-TP protocol, the payload can either fit
+inside one single CAN message or not, also considering the overhead the protocol
+is generating and the optional extended addressing. In the first case, the data
+is transmitted at once using a so-called Single Frame (SF). In the second case,
+ISO-TP defines a multi-frame protocol, in which the sender provides (through a
+First Frame - FF) the PDU length which is to be transmitted and also asks for a
+Flow Control (FC) frame, which provides the maximum supported size of a macro
+data block (``blocksize``) and the minimum time between the single CAN messages
+composing such block (``stmin``). Once this information has been received, the
+sender starts to send frames containing fragments of the data payload (called
+Consecutive Frames - CF), stopping after every ``blocksize``-sized block to wait
+confirmation from the receiver (which should then send another Flow Control
+frame to inform the sender about its availability to receive more data).
+
+How to Use ISO-TP
+=================
+
+As with others CAN protocols, the ISO-TP stack support is built into the
+Linux network subsystem for the CAN bus, aka. Linux-CAN or SocketCAN, and
+thus follows the same socket API.
+
+Creation and basic usage of an ISO-TP socket
+--------------------------------------------
+
+To use the ISO-TP stack, ``#include <linux/can/isotp.h>`` shall be used. A
+socket can then be created using the ``PF_CAN`` protocol family, the
+``SOCK_DGRAM`` type (as the underlying protocol is datagram-based by design)
+and the ``CAN_ISOTP`` protocol:
+
+.. code-block:: C
+
+    s = socket(PF_CAN, SOCK_DGRAM, CAN_ISOTP);
+
+After the socket has been successfully created, ``bind(2)`` shall be called to
+bind the socket to the desired CAN interface; to do so:
+
+* a TX CAN ID shall be specified as part of the sockaddr supplied to the call
+  itself, and
+* a RX CAN ID shall also specified, unless broadcast flags have been set
+  through socket option (explained below)
+
+Once bound to an interface, the socket can be read from and written to using
+the usual ``read(2)`` and ``write(2)`` system calls, as well as ``send(2)``,
+``sendmsg(2)``, ``recv(2)`` and ``recvmsg(2)``.
+Unlike the CAN_RAW socket API, only the data payload shall be specified in all
+these calls, as the CAN header is automatically filled by the ISO-TP stack
+using information supplied during socket creation. In the same way, the stack
+will use the transport mechanism when required (i.e., when the size of the data
+payload exceeds the MTU of the underlying CAN bus).
+
+The sockaddr structure used for SocketCAN has extensions for use with ISO-TP,
+as specified below:
+
+.. code-block:: C
+
+    struct sockaddr_can {
+        sa_family_t can_family;
+        int         can_ifindex;
+        union {
+            struct { canid_t rx_id, tx_id; } tp;
+        ...
+        } can_addr;
+    }
+
+* ``can_family`` and ``can_ifindex`` serve the same purpose as for other
+  SocketCAN sockets.
+
+* ``can_addr.tp.rx_id`` specifies the receive (RX) CAN ID and will be used as
+  a RX filter.
+
+* ``can_addr.tp.tx_id`` specifies the transmit (TX) CAN ID
+
+ISO-TP socket options
+---------------------
+
+When creating an ISO-TP socket, reasonable defaults are set. Some options can
+be modified with ``setsockopt(2)`` and/or read back with ``getsockopt(2)``.
+
+General options
+~~~~~~~~~~~~~~~
+
+General socket options can be passed using the ``CAN_ISOTP_OPTS`` optname:
+
+.. code-block:: C
+
+    struct can_isotp_options opts;
+    ret = setsockopt(s, SOL_CAN_ISOTP, CAN_ISOTP_OPTS, &opts, sizeof(opts))
+
+where the ``can_isotp_options`` structure has the following contents:
+
+.. code-block:: C
+
+    struct can_isotp_options {
+        u32 flags;
+        u32 frame_txtime;
+        u8  ext_address;
+        u8  txpad_content;
+        u8  rxpad_content;
+        u8  rx_ext_address;
+    };
+
+* ``flags``: modifiers to be applied to the default behaviour of the ISO-TP
+  stack. Following flags are available:
+
+  - ``CAN_ISOTP_LISTEN_MODE``: listen only (do not send FC frames); normally
+    used as a testing feature.
+  - ``CAN_ISOTP_EXTEND_ADDR``: enable extended addressing, using the byte
+    specified in ``ext_address`` as additional address byte.
+  - ``CAN_ISOTP_TX_PADDING``: enable padding for tranmsitted frames, using
+    ``txpad_content`` as value for the padding bytes.
+  - ``CAN_ISOTP_RX_PADDING``: enable padding for the received frames, using
+    ``rxpad_content`` as value for the padding bytes.
+  - ``CAN_ISOTP_CHK_PAD_LEN``: check for correct padding length on the received
+    frames.
+  - ``CAN_ISOTP_CHK_PAD_DATA``: check padding bytes on the received frames
+    against ``rxpad_content``; if ``CAN_ISOTP_RX_PADDING`` is not specified,
+    this flag is ignored.
+  - ``CAN_ISOTP_HALF_DUPLEX``: force ISO-TP socket in half duples mode
+    (that is, transport mechanism can only be incoming or outgoing at the same
+    time, not both).
+  - ``CAN_ISOTP_FORCE_TXSTMIN``: ignore stmin from received FC; normally
+    used as a testing feature.
+  - ``CAN_ISOTP_FORCE_RXSTMIN``: ignore CFs depending on rx stmin; normally
+    used as a testing feature.
+  - ``CAN_ISOTP_RX_EXT_ADDR``: use ``rx_ext_address`` instead of ``ext_address``
+    as extended addressing byte on the reception path.
+  - ``CAN_ISOTP_WAIT_TX_DONE``: wait until the frame is sent before returning
+    from ``write(2)`` and ``send(2)`` calls (i.e., blocking write operations).
+  - ``CAN_ISOTP_SF_BROADCAST``: use 1-to-N functional addressing (cannot be
+    specified alongside ``CAN_ISOTP_CF_BROADCAST``).
+  - ``CAN_ISOTP_CF_BROADCAST``: use 1-to-N transmission without flow control
+    (cannot be specified alongside ``CAN_ISOTP_SF_BROADCAST``).
+    NOTE: this is not covered by the ISO15765-2:2016 standard.
+  - ``CAN_ISOTP_DYN_FC_PARMS``: enable dynamic update of flow control
+    parameters.
+
+* ``frame_txtime``: frame transmission time (defined as N_As/N_Ar inside the
+  ISO standard); if ``0``, the default (or the last set value) is used.
+  To set the transmission time to ``0``, the ``CAN_ISOTP_FRAME_TXTIME_ZERO``
+  macro (equal to 0xFFFFFFFF) shall be used.
+
+* ``ext_address``: extended addressing byte, used if the
+  ``CAN_ISOTP_EXTEND_ADDR`` flag is specified.
+
+* ``txpad_content``: byte used as padding value for transmitted frames
+
+* ``rxpad_content``: byte used as padding value for received frames
+
+* ``rx_ext_address``: extended addressing byte for the reception path, used if
+  the ``CAN_ISOTP_RX_EXT_ADDR`` flag is specified.
+
+Flow Control options
+~~~~~~~~~~~~~~~~~~~~
+
+Flow Control (FC) options can be passed using the ``CAN_ISOTP_RECV_FC`` optname
+to provide the communication parameters for receiving ISO-TP PDUs.
+
+.. code-block:: C
+
+    struct can_isotp_fc_options fc_opts;
+    ret = setsockopt(s, SOL_CAN_ISOTP, CAN_ISOTP_RECV_FC, &fc_opts, sizeof(fc_opts));
+
+where the ``can_isotp_fc_options`` structure has the following contents:
+
+.. code-block:: C
+
+    struct can_isotp_options {
+        u8 bs;
+        u8 stmin;
+        u8 wftmax;
+    };
+
+* ``bs``: blocksize provided in flow control frames.
+
+* ``stmin``: minimum separation time provided in flow control frames; can
+  have the following values (others are reserved):
+  - 0x00 - 0x7F : 0 - 127 ms
+  - 0xF1 - 0xF9 : 100 us - 900 us
+
+* ``wftmax``: maximum number of wait frames provided in flow control frames.
+
+Link Layer options
+~~~~~~~~~~~~~~~~~~
+
+Link Layer (LL) options can be passed using the ``CAN_ISOTP_LL_OPTS`` optname:
+
+.. code-block:: C
+
+    struct can_isotp_ll_options ll_opts;
+    ret = setsockopt(s, SOL_CAN_ISOTP, CAN_ISOTP_LL_OPTS, &ll_opts, sizeof(ll_opts));
+
+where the ``can_isotp_ll_options`` structure has the following contents:
+
+.. code-block:: C
+
+    struct can_isotp_ll_options {
+        u8 mtu;
+        u8 tx_dl;
+        u8 tx_flags;
+    };
+
+* ``mtu``: generated and accepted CAN frame type, can be equal to ``CAN_MTU``
+  for classical CAN frames or ``CANFD_MTU`` for CAN FD frames.
+
+* ``tx_dl``: maximum payload length for transmitted frames, can have one value
+  among: 8, 12, 16, 20, 24, 32, 48, 64. Values above 8 only apply to CAN FD
+  traffic (i.e.: ``mtu = CANFD_MTU``).
+
+* ``tx_flags``: flags set into ``struct canfd_frame.flags`` at frame creation.
+  Only applies to CAN FD traffic (i.e.: ``mtu = CANFD_MTU``).
+
+Transmission stmin
+~~~~~~~~~~~~~~~~~~
+
+The transmission minimum separaton time (stmin) can be forced using the
+``CAN_ISOTP_TX_STMIN`` optname and providing an stmin value in microseconds as
+a 32bit unsigned integer; this will overwrite the value sent by the receiver in
+flow control frames:
+
+.. code-block:: C
+
+    uint32_t stmin;
+    ret = setsockopt(s, SOL_CAN_ISOTP, CAN_ISOTP_TX_STMIN, &stmin, sizeof(stmin));
+
+Reception stmin
+~~~~~~~~~~~~~~~
+
+The reception minimum separaton time (stmin) can be forced using the
+``CAN_ISOTP_RX_STMIN`` optname and providing an stmin value in microseconds as
+a 32bit unsigned integer; received Consecutive Frames (CF) which timestamps
+differ less than this value will be ignored:
+
+.. code-block:: C
+
+    uint32_t stmin;
+    ret = setsockopt(s, SOL_CAN_ISOTP, CAN_ISOTP_RX_STMIN, &stmin, sizeof(stmin));
+
+Multi-frame transport support
+-----------------------------
+
+The ISO-TP stack contained inside the Linux kernel supports the multi-frame
+transport mechanism defined by the standard, with the following constraints:
+
+* the maximum size of a PDU is defined by a module parameter, with an hard
+  limit imposed at build time
+* when a transmission is in progress, subsequent calls to ``write(2)`` will
+  block, while calls to ``send(2)`` will either block or fail depending on the
+  presence of the ``MSG_DONTWAIT`` flag
+* no support is present for sending "wait frames": whether a PDU can be fully
+  received or not is decided when the First Frame is received
+
+Errors
+------
+
+Following errors are reported to userspace:
+
+RX path errors
+~~~~~~~~~~~~~~
+
+============ ===============================================================
+-ETIMEDOUT   timeout of data reception
+-EILSEQ      sequence number mismatch during a multi-frame reception
+-EBADMSG     data reception with wrong padding
+============ ===============================================================
+
+TX path errors
+~~~~~~~~~~~~~~
+
+========== =================================================================
+-ECOMM     flow control reception timeout
+-EMSGSIZE  flow control reception overflow
+-EBADMSG   flow control reception with wrong layout/padding
+========== =================================================================
+
+Examples
+========
+
+Basic node example
+------------------
+
+Following example implements a node using "normal" physical addressing, with
+RX ID equal to 0x18DAF142 and a TX ID equal to 0x18DA42F1. All options are left
+to their default.
+
+.. code-block:: C
+
+  int s;
+  struct sockaddr_can addr;
+  int ret;
+
+  s = socket(PF_CAN, SOCK_DGRAM, CAN_ISOTP);
+  if (s < 0)
+      exit(1);
+
+  addr.can_family = AF_CAN;
+  addr.can_ifindex = if_nametoindex("can0");
+  addr.tp.tx_id = (0x18DA42F1 | CAN_EFF_FLAG);
+  addr.tp.rx_id = (0x18DAF142 | CAN_EFF_FLAG);
+
+  ret = bind(s, (struct sockaddr *)&addr, sizeof(addr));
+  if (ret < 0)
+      exit(1);
+
+  // Data can now be received using read(s, ...) and sent using write(s, ...)
+
+Additional examples
+-------------------
+
+More complete (and complex) examples can be found inside the ``isotp*`` userland
+tools, distributed as part of the ``can-utils`` utilities at:
+https://github.com/linux-can/can-utils
diff --git a/MAINTAINERS b/MAINTAINERS
index 6a233e1a3cf2..e0190b90d1a8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4695,6 +4695,7 @@ W:	https://github.com/linux-can
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git
 F:	Documentation/networking/can.rst
+F:	Documentation/networking/iso15765-2.rst
 F:	include/linux/can/can-ml.h
 F:	include/linux/can/core.h
 F:	include/linux/can/skb.h
-- 
2.44.0

Powered by blists - more mailing lists