lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAA8EJppa4hVBSenLgxc5MYxTfzPPf4exHvh8RWTP=p8mgB_RCw@mail.gmail.com>
Date: Sat, 30 Mar 2024 15:39:08 +0200
From: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
To: Krishna Kurapati PSSNV <quic_kriskura@...cinc.com>
Cc: Rob Herring <robh@...nel.org>, 
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, 
	Greg Kroah-Hartman <gregkh@...uxfoundation.org>, Conor Dooley <conor+dt@...nel.org>, 
	Miquel Raynal <miquel.raynal@...tlin.com>, Guenter Roeck <linux@...ck-us.net>, 
	Bjorn Helgaas <bhelgaas@...gle.com>, Kyle Tso <kyletso@...gle.com>, 
	Fabrice Gasnier <fabrice.gasnier@...s.st.com>, 
	Heikki Krogerus <heikki.krogerus@...ux.intel.com>, u.kleine-koenig@...gutronix.de, 
	AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>, devicetree@...r.kernel.org, 
	linux-usb@...r.kernel.org, linux-kernel@...r.kernel.org, 
	quic_ppratap@...cinc.com, quic_jackp@...cinc.com
Subject: Re: [RFC PATCH 0/2] Add gpio-usb-c-connector compatible

On Sat, 30 Mar 2024 at 11:13, Krishna Kurapati PSSNV
<quic_kriskura@...cinc.com> wrote:
> On 3/29/2024 6:23 PM, Dmitry Baryshkov wrote:
> > On Fri, 29 Mar 2024 at 09:20, Krishna Kurapati
> > <quic_kriskura@...cinc.com> wrote:
> >>
> >> QDU1000 IDP [1] has a Type-c connector and supports USB 3.0.
> >> However it relies on usb-conn-gpio driver to read the vbus and id
> >> gpio's and provide role switch. However the driver currently has
> >> only gpio-b-connector compatible present in ID table. Adding that
> >> in DT would mean that the device supports Type-B connector and not
> >> Type-c connector. Thanks to Dmitry Baryshkov for pointing it out [2].
> >
> > USB-B connector is pretty simple, it really has just an ID pin and
> > VBUS input, which translates to two GPIOs being routed from the
> > _connector_ itself.
> >
> > USB-C is much more complicated, it has two CC pins and a VBus power
> > pin. It is not enough just to measure CC pin levels. Moreover,
> > properly handling USB 3.0 inside a USB-C connector requires a separate
> > 'orientation' signal to tell the host which two lanes must be used for
> > the USB SS signals. Thus it is no longer possible to route just two
> > pins from the connector to the SoC.
> >
> > Having all that in mind, I suspect that you are not describing your
> > hardware properly. I suppose that you have a Type-C port controller /
> > redriver / switch, which handles CC lines communication and then
> > provides ID / VBUS signals to the host. In such a case, please
> > describe this TCPC in the DT file and use its compatible string
> > instead of "gpio-c-connector".
> >
>
> Hi Dmitry,
>
>   My bad. I must have provided more details of the HW.
>
>   I presume you are referring to addition of a connector node, type-c
> switch, pmic-glink and other remote endpoints like in other SoC's like
> SM8450/ SM8550/ SM8650.
>
>   This HW is slightly different. It has a Uni Phy for Super speed and
> hence no DP.

This is fine and it's irrelevant for the USB-C.

>   For orientation switching, on mobile SoC's, there is a provision for
> orientation gpio given in pmic-glink node and is handled in ucsi_glink
> driver. But on this version of HW, there is a USB-C Switch with its own
> firmware taking care of orientation switching. It takes 8 SS Lines and 2
> CC lines coming from connector as input and gives out 4 SS Lines (SS
> TX1/TX2 RX1/RX2) as output which go to the SoC. So orientation switch is
> done by the USB-C-switch in between and it automatically routes
> appropriate active SS Lane from connector to the SoC.

This is also fine. As I wrote, you _have_ the Type-C port controller.
So your DT file should be describing your hardware.

>   As usual like in other targets, the DP and DM lines from type-c
> connector go to the SoC directly.
>
>   To handle role switch, the VBUS and ID Pin connections are given to
> SoC as well. There is a vbus controller regulator present to provide
> vbus to connected peripherals in host mode.
>
>   There is no PPM entity (ADSP in mobile SoC's) and no UCSI involved
> here. Hence we rely on usb-conn-gpio to read the vbus/id and switch
> roles accordingly.

This is also fine.

You confirmed my suspicions. You have an external Type-C switch which
handles orientation (and most likely PD or non-PD power negotiation)
for you. It has GPIO outputs, etc.

But it is not a part of the connector. Instead of adding the
"gpio-usb-c-connector", add proper compatible string (see, how this is
handled e.g. by the spidev - it is a generic driver, but it requires
hardware-specific compatibles).
Your hardware description should look like:

typec {
    compatible = "your,switch";
    id-gpios = <&gpio 1>;
    vbus-gpios = <&gpio 2>;
    vbus-supplies = <&reg-vbus>;

    ports {
       #address-cells = <1>;
       #size-cells = <1>;
       port@0 {
          endpoint {
              remote-endpoint = <&usb_dwc3_hs_out>;
          };
       };
       port@1 {
          endpoint {
              remote-endpoint = <&usb_uni_phy_out>;
          };
      };
      /* No SBU port */
   };
};

Note, I haven't said anything regarding the driver. You can continue
using the usb-conn-gpio driver. Just add a compatible string for you
switch.

>
>   Hope this answers the query as to why we wanted to use usb-conn-gpio
> and why we were trying to add a new compatible.
>
> Regards,
> Krishna,
>
> >>
> >> This series intends to add that compatible in driver and bindings
> >> so that it can be used in QDU1000 IDP DT.
> >>
> >> [1]: https://lore.kernel.org/all/20240319091020.15137-3-quic_kbajaj@quicinc.com/
> >> [2]: https://lore.kernel.org/all/CAA8EJprXPvji8TgZu1idH7y4GtHtD4VmQABFBcRt-9BQaCberg@mail.gmail.com/
> >>
> >> Krishna Kurapati (2):
> >>    dt-bindings: connector: Add gpio-usb-c-connector compatible
> >>    usb: common: usb-conn-gpio: Update ID table to add usb-c connector
> >>
> >>   Documentation/devicetree/bindings/connector/usb-connector.yaml | 3 +++
> >>   drivers/usb/common/usb-conn-gpio.c                             | 1 +
> >>   2 files changed, 4 insertions(+)
> >>
> >> --
> >> 2.34.1
> >>
> >
> >
> > --
> > With best wishes
> > Dmitry



-- 
With best wishes
Dmitry

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ