| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20240403043416.3800259-4-sumit.garg@linaro.org>
Date: Wed, 3 Apr 2024 10:04:16 +0530
From: Sumit Garg <sumit.garg@...aro.org>
To: linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org
Cc: andersson@...nel.org,
konrad.dybcio@...aro.org,
robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org,
conor+dt@...nel.org,
stephan@...hold.net,
caleb.connolly@...aro.org,
neil.armstrong@...aro.org,
dmitry.baryshkov@...aro.org,
laetitia.mariottini@...com,
pascal.eberhard@...com,
abdou.saker@...com,
jimmy.lalande@...com,
benjamin.missey@....se.com,
daniel.thompson@...aro.org,
linux-kernel@...r.kernel.org,
Sumit Garg <sumit.garg@...aro.org>,
Jagdish Gediya <jagdish.gediya@...aro.org>
Subject: [PATCH v5 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS
Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
Box Core board based on the Qualcomm APQ8016E SoC.
Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 1GiB RAM
- 8GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
- USB ethernet adaptors (soldered)
Co-developed-by: Jagdish Gediya <jagdish.gediya@...aro.org>
Signed-off-by: Jagdish Gediya <jagdish.gediya@...aro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@...aro.org>
Reviewed-by: Stephan Gerhold <stephan@...hold.net>
Signed-off-by: Sumit Garg <sumit.garg@...aro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++
2 files changed, 492 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 39889d5f8e12..ad55e52e950b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -5,6 +5,7 @@ apq8016-sbc-usb-host-dtbs := apq8016-sbc.dtb apq8016-sbc-usb-host.dtbo
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-usb-host.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3-camera-mezzanine.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8016-schneider-hmibsc.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
new file mode 100644
index 000000000000..75c6137e5a11
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
+
+/ {
+ model = "Schneider Electric HMIBSC Board";
+ compatible = "schneider,apq8016-hmibsc", "qcom,apq8016";
+
+ aliases {
+ i2c1 = &blsp_i2c6;
+ i2c3 = &blsp_i2c4;
+ i2c4 = &blsp_i2c3;
+ mmc0 = &sdhc_1; /* eMMC */
+ mmc1 = &sdhc_2; /* SD card */
+ serial0 = &blsp_uart1;
+ serial1 = &blsp_uart2;
+ spi0 = &blsp_spi5;
+ usid0 = &pm8916_0;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7533_out>;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-0 = <&msm_key_volp_n_default>;
+ pinctrl-names = "default";
+
+ button {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pm8916_mpps_leds>;
+ pinctrl-names = "default";
+
+ led-1 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_YELLOW>;
+ gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ led-2 {
+ function = LED_FUNCTION_BLUETOOTH;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+
+ memory@...00000 {
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ reserved-memory {
+ ramoops@...00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xbff00000 0x0 0x100000>;
+ record-size = <0x20000>;
+ console-size = <0x20000>;
+ ftrace-size = <0x20000>;
+ ecc-size = <16>;
+ };
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503";
+ reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>;
+ initial-mode = <1>;
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb_id_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c3 {
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+};
+
+&blsp_i2c4 {
+ status = "okay";
+
+ adv_bridge: bridge@39 {
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+ interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+
+ adi,dsi-lanes = <4>;
+ clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+ clock-names = "cec";
+ pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+
+ avdd-supply = <&pm8916_l6>;
+ a2vdd-supply = <&pm8916_l6>;
+ dvdd-supply = <&pm8916_l6>;
+ pvdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
+
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+ pinctrl-names = "default","sleep";
+ #sound-dai-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c6 {
+ status = "okay";
+
+ rtc@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+};
+
+&blsp_spi5 {
+ cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm@0 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <500000>;
+ };
+};
+
+&blsp_uart1 {
+ label = "UART0";
+ status = "okay";
+};
+
+&blsp_uart2 {
+ label = "UART1";
+ status = "okay";
+};
+
+&lpass {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&adv7533_in>;
+};
+
+&pm8916_codec {
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ status = "okay";
+};
+
+&pm8916_gpios {
+ gpio-line-names =
+ "USB_HUB_RESET_N_PM",
+ "USB_SW_SEL_PM",
+ "NC",
+ "NC";
+
+ usb_hub_reset_pm: usb-hub-reset-pm-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-high;
+ };
+
+ usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-low;
+ };
+
+ usb_sw_sel_pm: usb-sw-sel-pm-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-high;
+ };
+
+ usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-low;
+ };
+};
+
+&pm8916_mpps {
+ gpio-line-names =
+ "NC",
+ "WLAN_LED_CTRL",
+ "BT_LED_CTRL",
+ "NC";
+
+ pm8916_mpps_leds: pm8916-mpps-state {
+ pins = "mpp2", "mpp3";
+ function = "digital";
+ output-low;
+ };
+};
+
+&pm8916_resin {
+ linux,code = <KEY_POWER>;
+ status = "okay";
+};
+
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
+ pinctrl-names = "default", "sleep";
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&sound {
+ pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
+ pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
+ pinctrl-names = "default", "sleep";
+ model = "HMIBSC";
+ audio-routing =
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+ status = "okay";
+
+ quaternary-dai-link {
+ link-name = "ADV7533";
+ cpu {
+ sound-dai = <&lpass MI2S_QUATERNARY>;
+ };
+ codec {
+ sound-dai = <&adv_bridge 0>;
+ };
+ };
+
+ primary-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
+ };
+ };
+
+ tertiary-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
+ };
+ };
+};
+
+&tlmm {
+ pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>;
+ pinctrl-names = "default";
+
+ adv7533_int_active: adv533-int-active-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_int_suspend: adv7533-int-suspend-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ adv7533_switch_active: adv7533-switch-active-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_switch_suspend: adv7533-switch-suspend-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ msm_key_volp_n_default: msm-key-volp-n-default-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ sdc2_cd_default: sdc2-cd-default-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ /*
+ * UART1 being the debug console supports various modes of
+ * operation (RS-232/485/422) controlled via GPIOs configured
+ * mux as follows:
+ *
+ * gpio100 gpio99 UART mode
+ * 0 0 loopback
+ * 0 1 RS-232
+ * 1 0 RS-485
+ * 1 1 RS-422
+ *
+ * The default mode configured here is RS-232 mode.
+ */
+ uart1_mux0_rs232_high: uart1-mux0-rs232-state {
+ bootph-all;
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+
+ uart1_mux1_rs232_low: uart1-mux1-rs232-state {
+ bootph-all;
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+ pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+ pinctrl-names = "default", "device";
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&wcnss {
+ firmware-name = "qcom/apq8016/wcnss.mbn";
+ status = "okay";
+};
+
+&wcnss_ctrl {
+ firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+&wcnss_iris {
+ compatible = "qcom,wcn3620";
+};
+
+&wcnss_mem {
+ status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in msm8916.dtsi */
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&blsp_i2c4_default {
+ drive-strength = <16>;
+};
+
+&blsp_i2c6_default {
+ drive-strength = <16>;
+};
+
+&blsp_uart1_default {
+ bootph-all;
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
--
2.34.1
Powered by blists - more mailing lists