| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 4 Apr 2024 09:44:50 +0200
From: Bastien Curutchet <bastien.curutchet@...tlin.com>
To: bastien.curutchet@...tlin.com,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Jiri Slaby <jirislaby@...nel.org>
Cc: linux-kernel@...r.kernel.org,
linux-serial@...r.kernel.org,
Thomas Petazzoni <thomas.petazzoni@...tlin.com>,
herve.codina@...tlin.com,
christophercordahi@...ometrics.ca
Subject: [PATCH 1/1] serial: 8250_of: Add clock_notifier
The UART's input clock rate can change at runtime but this is not
handled by the driver.
Add a clock_notifier callback that updates the divisors when the input
clock is updated. The serial8250_update_uartclk() is used to do so.
PRE_RATE_CHANGE and ABORT_RATE_CHANGE notifications are ignored, only
the POST_RATE_CHANGE is used.
Reorder the #include to match alphabetic order.
It has been tested on a DAVINCI/OMAP-L138 processor.
Signed-off-by: Bastien Curutchet <bastien.curutchet@...tlin.com>
---
drivers/tty/serial/8250/8250_of.c | 48 ++++++++++++++++++++++++++++---
1 file changed, 44 insertions(+), 4 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 5d1dd992d8fb..6d570164d906 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -6,18 +6,19 @@
*/
#include <linux/bits.h>
+#include <linux/clk.h>
#include <linux/console.h>
#include <linux/math.h>
#include <linux/module.h>
-#include <linux/slab.h>
-#include <linux/serial_core.h>
-#include <linux/serial_reg.h>
+#include <linux/notifier.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/pm_runtime.h>
-#include <linux/clk.h>
#include <linux/reset.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
#include "8250.h"
@@ -26,6 +27,7 @@ struct of_serial_info {
struct reset_control *rst;
int type;
int line;
+ struct notifier_block clk_notifier;
};
/* Nuvoton NPCM timeout register */
@@ -58,6 +60,29 @@ static int npcm_setup(struct uart_port *port)
return 0;
}
+static inline struct of_serial_info *clk_nb_to_info(struct notifier_block *nb)
+{
+ return container_of(nb, struct of_serial_info, clk_notifier);
+}
+
+static int of_platform_serial_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
+ void *data)
+{
+ struct of_serial_info *info = clk_nb_to_info(nb);
+ struct uart_8250_port *port8250 = serial8250_get_port(info->line);
+ struct clk_notifier_data *ndata = data;
+
+ if (IS_ERR(info->clk))
+ return NOTIFY_DONE;
+
+ if (event == POST_RATE_CHANGE) {
+ serial8250_update_uartclk(&port8250->port, ndata->new_rate);
+ return NOTIFY_OK;
+ }
+
+ return NOTIFY_DONE;
+}
+
/*
* Fill a struct uart_port for a given device node
*/
@@ -218,7 +243,19 @@ static int of_platform_serial_probe(struct platform_device *ofdev)
info->type = port_type;
info->line = ret;
platform_set_drvdata(ofdev, info);
+
+ if (info->clk) {
+ info->clk_notifier.notifier_call = of_platform_serial_clk_notifier_cb;
+ ret = clk_notifier_register(info->clk, &info->clk_notifier);
+ if (ret) {
+ dev_err_probe(port8250.port.dev, ret, "Failed to set the clock notifier\n");
+ goto err_unregister;
+ }
+ }
+
return 0;
+err_unregister:
+ serial8250_unregister_port(info->line);
err_dispose:
pm_runtime_put_sync(&ofdev->dev);
pm_runtime_disable(&ofdev->dev);
@@ -234,6 +271,9 @@ static void of_platform_serial_remove(struct platform_device *ofdev)
{
struct of_serial_info *info = platform_get_drvdata(ofdev);
+ if (info->clk)
+ clk_notifier_unregister(info->clk, &info->clk_notifier);
+
serial8250_unregister_port(info->line);
reset_control_assert(info->rst);
--
2.44.0
Powered by blists - more mailing lists