| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1a14ac6e-30e9-048e-50cc-c1c3aacc2118@linux.intel.com>
Date: Mon, 8 Apr 2024 12:54:54 +0300 (EEST)
From: Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
To: Niklas Schnelle <schnelle@...ux.ibm.com>
cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Jiri Slaby <jirislaby@...nel.org>,
linux-serial <linux-serial@...r.kernel.org>,
Arnd Bergmann <arnd@...nel.org>, Heiko Carstens <hca@...ux.ibm.com>,
LKML <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 1/1] tty: serial: handle HAS_IOPORT dependencies
On Fri, 5 Apr 2024, Niklas Schnelle wrote:
> In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
> compile time. We thus need to add HAS_IOPORT as dependency for those
> drivers using them unconditionally. For 8250 based drivers some support
> MMIO only use so fence only the parts requiring I/O ports.
>
> Co-developed-by: Arnd Bergmann <arnd@...nel.org>
> Signed-off-by: Arnd Bergmann <arnd@...nel.org>
> Signed-off-by: Niklas Schnelle <schnelle@...ux.ibm.com>
> ---
> Note: This patch does not depend any not-yet-mainline HAS_IOPORT changes
> and may be merged via subsystem specific trees at your earliest
> convenience.
>
> Note 2: This was previously acked here:
> https://lore.kernel.org/all/2023053050-prodigal-shine-4d1c@gregkh/
> Given this was almost a year ago and didn't apply then I didn't
> carry the Ack over though.
>
> drivers/tty/Kconfig | 4 +--
> drivers/tty/serial/8250/8250_early.c | 4 +++
> drivers/tty/serial/8250/8250_pci.c | 14 ++++++++++
> drivers/tty/serial/8250/8250_port.c | 42 +++++++++++++++++++++++-----
> drivers/tty/serial/8250/Kconfig | 7 ++---
> drivers/tty/serial/Kconfig | 2 +-
> 6 files changed, 59 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
> index a45d423ad10f..63a494d36a1f 100644
> --- a/drivers/tty/Kconfig
> +++ b/drivers/tty/Kconfig
> @@ -220,7 +220,7 @@ config MOXA_INTELLIO
>
> config MOXA_SMARTIO
> tristate "Moxa SmartIO support v. 2.0"
> - depends on SERIAL_NONSTANDARD && PCI
> + depends on SERIAL_NONSTANDARD && PCI && HAS_IOPORT
> help
> Say Y here if you have a Moxa SmartIO multiport serial card and/or
> want to help develop a new version of this driver.
> @@ -302,7 +302,7 @@ config GOLDFISH_TTY_EARLY_CONSOLE
>
> config IPWIRELESS
> tristate "IPWireless 3G UMTS PCMCIA card support"
> - depends on PCMCIA && NETDEVICES
> + depends on PCMCIA && NETDEVICES && HAS_IOPORT
> select PPP
> help
> This is a driver for 3G UMTS PCMCIA card from IPWireless company. In
> diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
> index e3f482fd3de4..8f9aec2e7c7d 100644
> --- a/drivers/tty/serial/8250/8250_early.c
> +++ b/drivers/tty/serial/8250/8250_early.c
> @@ -46,8 +46,10 @@ static unsigned int serial8250_early_in(struct uart_port *port, int offset)
> return readl(port->membase + offset);
> case UPIO_MEM32BE:
> return ioread32be(port->membase + offset);
> +#ifdef CONFIG_HAS_IOPORT
> case UPIO_PORT:
> return inb(port->iobase + offset);
> +#endif
> default:
> return 0;
> }
> @@ -70,9 +72,11 @@ static void serial8250_early_out(struct uart_port *port, int offset, int value)
> case UPIO_MEM32BE:
> iowrite32be(value, port->membase + offset);
> break;
> +#ifdef CONFIG_HAS_IOPORT
> case UPIO_PORT:
> outb(value, port->iobase + offset);
> break;
> +#endif
> }
> }
>
> diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
> index 0d35c77fad9e..38ac5236d2ea 100644
> --- a/drivers/tty/serial/8250/8250_pci.c
> +++ b/drivers/tty/serial/8250/8250_pci.c
> @@ -928,6 +928,7 @@ static int pci_netmos_init(struct pci_dev *dev)
> return num_serial;
> }
>
> +#ifdef CONFIG_HAS_IOPORT
> /*
> * These chips are available with optionally one parallel port and up to
> * two serial ports. Unfortunately they all have the same product id.
> @@ -1054,6 +1055,7 @@ static void pci_ite887x_exit(struct pci_dev *dev)
> ioport &= 0xffff;
> release_region(ioport, ITE_887x_IOSIZE);
> }
> +#endif /* CONFIG_HAS_IOPORT */
>
> /*
> * Oxford Semiconductor Inc.
> @@ -1328,6 +1330,7 @@ static int pci_oxsemi_tornado_setup(struct serial_private *priv,
> #define QOPR_CLOCK_X8 0x0003
> #define QOPR_CLOCK_RATE_MASK 0x0003
>
> +#ifdef CONFIG_HAS_IOPORT
> /* Quatech devices have their own extra interface features */
> static struct pci_device_id quatech_cards[] = {
> { PCI_DEVICE_DATA(QUATECH, QSC100, 1) },
> @@ -1547,6 +1550,7 @@ static int pci_quatech_setup(struct serial_private *priv,
> pci_warn(priv->dev, "software control of RS422 features not currently supported.\n");
> return pci_default_setup(priv, board, port, idx);
> }
> +#endif /* CONFIG_HAS_IOPORT */
>
> static int pci_default_setup(struct serial_private *priv,
> const struct pciserial_board *board,
> @@ -1826,6 +1830,7 @@ static int skip_tx_en_setup(struct serial_private *priv,
> return pci_default_setup(priv, board, port, idx);
> }
>
> +#ifdef CONFIG_HAS_IOPORT
> static void kt_handle_break(struct uart_port *p)
> {
> struct uart_8250_port *up = up_to_u8250p(p);
> @@ -1869,6 +1874,7 @@ static int kt_serial_setup(struct serial_private *priv,
> port->port.handle_break = kt_handle_break;
> return skip_tx_en_setup(priv, board, port, idx);
> }
> +#endif /* CONFIG_HAS_IOPORT */
>
> static int pci_eg20t_init(struct pci_dev *dev)
> {
> @@ -1913,6 +1919,7 @@ pci_wch_ch38x_setup(struct serial_private *priv,
> #define CH384_XINT_ENABLE_REG 0xEB
> #define CH384_XINT_ENABLE_BIT 0x02
>
> +#ifdef CONFIG_HAS_IOPORT
> static int pci_wch_ch38x_init(struct pci_dev *dev)
> {
> int max_port;
> @@ -1940,6 +1947,7 @@ static void pci_wch_ch38x_exit(struct pci_dev *dev)
> iobase = pci_resource_start(dev, 0);
> outb(0x0, iobase + CH384_XINT_ENABLE_REG);
> }
> +#endif /* CONFIG_HAS_IOPORT */
>
>
> static int
> @@ -2171,6 +2179,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .subdevice = PCI_ANY_ID,
> .setup = ce4100_serial_setup,
> },
> +#ifdef CONFIG_HAS_IOPORT
> {
> .vendor = PCI_VENDOR_ID_INTEL,
> .device = PCI_DEVICE_ID_INTEL_PATSBURG_KT,
> @@ -2190,6 +2199,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .setup = pci_default_setup,
> .exit = pci_ite887x_exit,
> },
> +#endif
> /*
> * National Instruments
> */
> @@ -2311,6 +2321,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .exit = pci_ni8430_exit,
> },
> /* Quatech */
> +#ifdef CONFIG_HAS_IOPORT
> {
> .vendor = PCI_VENDOR_ID_QUATECH,
> .device = PCI_ANY_ID,
> @@ -2319,6 +2330,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .init = pci_quatech_init,
> .setup = pci_quatech_setup,
> },
> +#endif
> /*
> * Panacom
> */
> @@ -2836,6 +2848,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .subdevice = PCI_ANY_ID,
> .setup = pci_wch_ch38x_setup,
> },
> +#ifdef CONFIG_HAS_IOPORT
> /* WCH CH384 8S card (16850 clone) */
> {
> .vendor = PCIE_VENDOR_ID_WCH,
> @@ -2846,6 +2859,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
> .exit = pci_wch_ch38x_exit,
> .setup = pci_wch_ch38x_setup,
> },
> +#endif
> /*
> * Broadcom TruManage (NetXtreme)
> */
> diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
> index fc9dd5d45295..1c5e39c1a469 100644
> --- a/drivers/tty/serial/8250/8250_port.c
> +++ b/drivers/tty/serial/8250/8250_port.c
> @@ -338,6 +338,7 @@ static void default_serial_dl_write(struct uart_8250_port *up, u32 value)
> serial_out(up, UART_DLM, value >> 8 & 0xff);
> }
>
> +#ifdef CONFIG_HAS_IOPORT
> static unsigned int hub6_serial_in(struct uart_port *p, int offset)
> {
> offset = offset << p->regshift;
> @@ -351,6 +352,7 @@ static void hub6_serial_out(struct uart_port *p, int offset, int value)
> outb(p->hub6 - 1 + offset, p->iobase);
> outb(value, p->iobase + 1);
> }
> +#endif /* CONFIG_HAS_IOPORT */
>
> static unsigned int mem_serial_in(struct uart_port *p, int offset)
> {
> @@ -400,6 +402,7 @@ static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
> return ioread32be(p->membase + offset);
> }
>
> +#ifdef CONFIG_HAS_IOPORT
> static unsigned int io_serial_in(struct uart_port *p, int offset)
> {
> offset = offset << p->regshift;
> @@ -411,6 +414,24 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
> offset = offset << p->regshift;
> outb(value, p->iobase + offset);
> }
> +#endif
> +static unsigned int no_serial_in(struct uart_port *p, int offset)
> +{
> + return (unsigned int)-1;
> +}
> +
> +static void no_serial_out(struct uart_port *p, int offset, int value)
> +{
> +}
> +
> +#ifdef CONFIG_HAS_IOPORT
> +static inline bool is_upf_fourport(struct uart_port *port)
> +{
> + return port->flags & UPF_FOURPORT;
> +}
> +#else
> +#define is_upf_fourport(x) false
> +#endif
>
> static int serial8250_default_handle_irq(struct uart_port *port);
>
> @@ -422,10 +443,12 @@ static void set_io_from_upio(struct uart_port *p)
> up->dl_write = default_serial_dl_write;
>
> switch (p->iotype) {
> +#ifdef CONFIG_HAS_IOPORT
> case UPIO_HUB6:
> p->serial_in = hub6_serial_in;
> p->serial_out = hub6_serial_out;
> break;
> +#endif
>
> case UPIO_MEM:
> p->serial_in = mem_serial_in;
> @@ -446,11 +469,16 @@ static void set_io_from_upio(struct uart_port *p)
> p->serial_in = mem32be_serial_in;
> p->serial_out = mem32be_serial_out;
> break;
> -
> - default:
> +#ifdef CONFIG_HAS_IOPORT
> + case UPIO_PORT:
> p->serial_in = io_serial_in;
> p->serial_out = io_serial_out;
> break;
> +#endif
> + default:
> + WARN(1, "Unsupported UART type %x\n", p->iotype);
> + p->serial_in = no_serial_in;
> + p->serial_out = no_serial_out;
> }
> /* Remember loaded iotype */
> up->cur_iotype = p->iotype;
> @@ -1318,7 +1346,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
> unsigned long irqs;
> int irq;
>
> - if (port->flags & UPF_FOURPORT) {
> + if (is_upf_fourport(port)) {
> ICP = (port->iobase & 0xfe0) | 0x1f;
> save_ICP = inb_p(ICP);
> outb_p(0x80, ICP);
> @@ -1337,7 +1365,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
> irqs = probe_irq_on();
> serial8250_out_MCR(up, 0);
> udelay(10);
> - if (port->flags & UPF_FOURPORT) {
> + if (is_upf_fourport(port)) {
> serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
> } else {
> serial8250_out_MCR(up,
> @@ -1361,7 +1389,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
> serial_out(up, UART_IER, save_ier);
> uart_port_unlock_irq(port);
>
> - if (port->flags & UPF_FOURPORT)
> + if (is_upf_fourport(port))
> outb_p(save_ICP, ICP);
>
> port->irq = (irq > 0) ? irq : 0;
> @@ -2438,7 +2466,7 @@ int serial8250_do_startup(struct uart_port *port)
> */
> up->ier = UART_IER_RLSI | UART_IER_RDI;
>
> - if (port->flags & UPF_FOURPORT) {
> + if (is_upf_fourport(port)) {
> unsigned int icp;
> /*
> * Enable interrupts on the AST Fourport board
> @@ -2483,7 +2511,7 @@ void serial8250_do_shutdown(struct uart_port *port)
> serial8250_release_dma(up);
>
> uart_port_lock_irqsave(port, &flags);
> - if (port->flags & UPF_FOURPORT) {
> + if (is_upf_fourport(port)) {
> /* reset interrupts on the AST Fourport board */
> inb((port->iobase & 0xfe0) | 0x1f);
> port->mctrl |= TIOCM_OUT1;
> diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
> index 47ff50763c04..54bf98869abf 100644
> --- a/drivers/tty/serial/8250/Kconfig
> +++ b/drivers/tty/serial/8250/Kconfig
> @@ -6,7 +6,6 @@
>
> config SERIAL_8250
> tristate "8250/16550 and compatible serial support"
> - depends on !S390
Why? Your changelogs gives zero insight on this change.
> select SERIAL_CORE
> select SERIAL_MCTRL_GPIO if GPIOLIB
> help
> @@ -72,7 +71,7 @@ config SERIAL_8250_16550A_VARIANTS
>
> config SERIAL_8250_FINTEK
> bool "Support for Fintek variants"
> - depends on SERIAL_8250
> + depends on SERIAL_8250 && HAS_IOPORT
> help
> Selecting this option will add support for the RS232 and RS485
> capabilities of the Fintek F81216A LPC to 4 UART as well similar
> @@ -136,7 +135,7 @@ config SERIAL_8250_PCILIB
>
> config SERIAL_8250_PCI
> tristate "8250/16550 PCI device support"
> - depends on SERIAL_8250 && PCI
> + depends on SERIAL_8250 && PCI && HAS_IOPORT
> select SERIAL_8250_PCILIB
> default SERIAL_8250
> help
> @@ -163,7 +162,7 @@ config SERIAL_8250_HP300
>
> config SERIAL_8250_CS
> tristate "8250/16550 PCMCIA device support"
> - depends on PCMCIA && SERIAL_8250
> + depends on PCMCIA && SERIAL_8250 && HAS_IOPORT
> help
> Say Y here to enable support for 16-bit PCMCIA serial devices,
> including serial port cards, modems, and the modem functions of
What about drivers that use SERIAL8250_PORT()?
Also port provided in 8250_PNP might expect it I think.
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index ffcf4882b25f..92c85e805c2a 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -874,7 +874,7 @@ config SERIAL_TXX9_STDSERIAL
>
> config SERIAL_JSM
> tristate "Digi International NEO and Classic PCI Support"
> - depends on PCI
> + depends on PCI && HAS_IOPORT
> select SERIAL_CORE
> help
> This is a driver for Digi International's Neo and Classic series
>
--
i.
Powered by blists - more mailing lists