[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240417073412.GD3894@thinkpad>
Date: Wed, 17 Apr 2024 13:04:12 +0530
From: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To: Alexandru Gagniuc <mr.nuke.me@...il.com>
Cc: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Lorenzo Pieralisi <lpieralisi@...nel.org>,
Krzysztof Wilczyński <kw@...ux.com>,
Rob Herring <robh@...nel.org>, Bjorn Helgaas <bhelgaas@...gle.com>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...nel.org>, linux-arm-msm@...r.kernel.org,
linux-pci@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-phy@...ts.infradead.org,
linux-clk@...r.kernel.org
Subject: Re: [PATCH v3 7/7] arm64: dts: qcom: ipq9574: add PCIe2 nodes
On Mon, Apr 15, 2024 at 01:20:52PM -0500, Alexandru Gagniuc wrote:
> On ipq9574, there are 4 PCIe controllers. Describe the pcie2 node, and
> its PHY in devicetree.
>
> Only pcie2 is described, because only hardware using that controller
> was available for testing.
>
You should describe all the instances in DT. Since the unused ones will be
'disabled', it won't affect anyone.
> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@...il.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 93 ++++++++++++++++++++++++++-
> 1 file changed, 92 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 7f2e5cbf3bbb..f075e2715300 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -300,7 +300,7 @@ gcc: clock-controller@...0000 {
> <0>,
> <0>,
> <0>,
> - <0>,
> + <&pcie2_phy>,
> <0>,
> <0>;
> #clock-cells = <1>;
> @@ -745,6 +745,97 @@ frame@...8000 {
> status = "disabled";
> };
> };
> +
> + pcie2_phy: phy@...00 {
> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x0008c000 0x14f4>;
> +
> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> + <&gcc GCC_PCIE2_AHB_CLK>,
> + <&gcc GCC_PCIE2_PIPE_CLK>,
> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
> + clock-names = "aux",
> + "cfg_ahb",
> + "pipe",
> + "anoc",
> + "snoc";
> +
> + clock-output-names = "pcie_phy2_pipe_clk";
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> +
> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
> + reset-names = "phy",
> + "common";
> + status = "disabled";
> + };
> +
> + pcie2: pcie@...00000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x20000000 0xf1d>,
> + <0x20000f20 0xa8>,
> + <0x20001000 0x1000>,
> + <0x00088000 0x4000>,
> + <0x20100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> +
> + ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>, /* I/O */
Please use below range:
<0x01000000 0x0 0x00000000 0x20200000 0x0 0x00100000>
<0x02000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>
> + <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>; /* MEM */
> +
> + device_type = "pci";
> + linux,pci-domain = <3>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <2>;
> + max-link-speed = <3>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + phys = <&pcie2_phy>;
> + phy-names = "pciephy";
> +
> + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 164
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 0 165
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 0 186
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 0 187
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
Use a single line for each INTX entry even if it exceeds 80 column width.
- Mani
--
மணிவண்ணன் சதாசிவம்
Powered by blists - more mailing lists