[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <e8957b07-692f-7d38-e276-b0e3791d31f4@gmail.com>
Date: Thu, 18 Apr 2024 10:33:23 -0500
From: mr.nuke.me@...il.com
To: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
Cc: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Lorenzo Pieralisi <lpieralisi@...nel.org>,
Krzysztof WilczyĆski <kw@...ux.com>,
Rob Herring <robh@...nel.org>, Bjorn Helgaas <bhelgaas@...gle.com>,
Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley
<conor+dt@...nel.org>, Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
Michael Turquette <mturquette@...libre.com>, Stephen Boyd
<sboyd@...nel.org>, linux-arm-msm@...r.kernel.org,
linux-pci@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-phy@...ts.infradead.org,
linux-clk@...r.kernel.org
Subject: Re: [PATCH v3 7/7] arm64: dts: qcom: ipq9574: add PCIe2 nodes
On 4/17/24 02:34, Manivannan Sadhasivam wrote:
> On Mon, Apr 15, 2024 at 01:20:52PM -0500, Alexandru Gagniuc wrote:
>> On ipq9574, there are 4 PCIe controllers. Describe the pcie2 node, and
>> its PHY in devicetree.
>>
>> Only pcie2 is described, because only hardware using that controller
>> was available for testing.
>>
>
> You should describe all the instances in DT. Since the unused ones will be
> 'disabled', it won't affect anyone.
My concern with untested but "disabled" descriptions is that someone may
think it's supported, try to enable it on their board, and run into
issues. Theoretically, we could describe pcie3, as it uses the same
gen3x2 phy.
The pcie0 and pcie1 use a gen3x1 phy, which I do not support in this
series. I would have to leave the "phys" and "phy-names" for these
nodes, leading to an incomplete description
Given this info, do you still wish that I add all other pcie nodes?
>> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@...il.com>
>> ---
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 93 ++++++++++++++++++++++++++-
>> 1 file changed, 92 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index 7f2e5cbf3bbb..f075e2715300 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -300,7 +300,7 @@ gcc: clock-controller@...0000 {
>> <0>,
>> <0>,
>> <0>,
>> - <0>,
>> + <&pcie2_phy>,
>> <0>,
>> <0>;
>> #clock-cells = <1>;
>> @@ -745,6 +745,97 @@ frame@...8000 {
>> status = "disabled";
>> };
>> };
>> +
>> + pcie2_phy: phy@...00 {
>> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
>> + reg = <0x0008c000 0x14f4>;
>> +
>> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
>> + <&gcc GCC_PCIE2_AHB_CLK>,
>> + <&gcc GCC_PCIE2_PIPE_CLK>,
>> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
>> + clock-names = "aux",
>> + "cfg_ahb",
>> + "pipe",
>> + "anoc",
>> + "snoc";
>> +
>> + clock-output-names = "pcie_phy2_pipe_clk";
>> + #clock-cells = <0>;
>> + #phy-cells = <0>;
>> +
>> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
>> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
>> + reset-names = "phy",
>> + "common";
>> + status = "disabled";
>> + };
>> +
>> + pcie2: pcie@...00000 {
>> + compatible = "qcom,pcie-ipq9574";
>> + reg = <0x20000000 0xf1d>,
>> + <0x20000f20 0xa8>,
>> + <0x20001000 0x1000>,
>> + <0x00088000 0x4000>,
>> + <0x20100000 0x1000>;
>> + reg-names = "dbi", "elbi", "atu", "parf", "config";
>> +
>> + ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>, /* I/O */
>
> Please use below range:
>
> <0x01000000 0x0 0x00000000 0x20200000 0x0 0x00100000>
> <0x02000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>
>
Of course, thank you.
>> + <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>; /* MEM */
>> +
>> + device_type = "pci";
>> + linux,pci-domain = <3>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <2>;
>> + max-link-speed = <3>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> +
>> + phys = <&pcie2_phy>;
>> + phy-names = "pciephy";
>> +
>> + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 0 164
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 0 165
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 0 186
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 0 187
>> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>
> Use a single line for each INTX entry even if it exceeds 80 column width.
Yes. Will do.
> - Mani
>
Powered by blists - more mailing lists