lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date: Fri, 19 Apr 2024 17:35:18 +0200
From: Josua Mayer <josua@...id-run.com>
To: Michael Hennerich <michael.hennerich@...log.com>, 
 "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, 
 Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, 
 Rob Herring <robh@...nel.org>, 
 Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, 
 Conor Dooley <conor+dt@...nel.org>, 
 Alexandru Tachici <alexandru.tachici@...log.com>, 
 Andrew Lunn <andrew@...n.ch>, Heiner Kallweit <hkallweit1@...il.com>, 
 Russell King <linux@...linux.org.uk>
Cc: Jon Nettleton <jon@...id-run.com>, 
 Yazan Shhady <yazan.shhady@...id-run.com>, netdev@...r.kernel.org, 
 devicetree@...r.kernel.org, linux-kernel@...r.kernel.org, 
 Josua Mayer <josua@...id-run.com>
Subject: [PATCH net-next 2/2] net: phy: adin: add support for setting led-,
 link-status-pin polarity

ADIN1300 supports software control over pin polarity for both LED_0 and
LINK_ST pins.

Configure the polarity during probe based on device-tree properties.

Led polarity is only set if specified in device-tree, otherwise the phy
can choose either active-low or active-high based on external line
voltage. Link-status polarity is set to active-high as default if not
specified, which is always the reset-default.

Signed-off-by: Josua Mayer <josua@...id-run.com>
---
 drivers/net/phy/adin.c | 53 ++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
index 2e1a46e121d9..53159dea6381 100644
--- a/drivers/net/phy/adin.c
+++ b/drivers/net/phy/adin.c
@@ -114,6 +114,9 @@
 
 #define ADIN1300_CDIAG_FLT_DIST(x)		(0xba21 + (x))
 
+#define ADIN1300_LED_A_INV_EN_REG		0xbc01
+#define   ADIN1300_LED_A_INV_EN			BIT(0)
+
 #define ADIN1300_GE_SOFT_RESET_REG		0xff0c
 #define   ADIN1300_GE_SOFT_RESET		BIT(0)
 
@@ -158,6 +161,9 @@
 #define ADIN1300_RMII_20_BITS			0x0004
 #define ADIN1300_RMII_24_BITS			0x0005
 
+#define ADIN1300_GE_LNK_STAT_INV_EN_REG		0xff3c
+#define   ADIN1300_GE_LNK_STAT_INV_EN		BIT(0)
+
 /**
  * struct adin_cfg_reg_map - map a config value to aregister value
  * @cfg:	value in device configuration
@@ -522,6 +528,49 @@ static int adin_config_clk_out(struct phy_device *phydev)
 			      ADIN1300_GE_CLK_CFG_MASK, sel);
 }
 
+static int adin_config_pin_polarity(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+	u32 val;
+
+	/* set led polarity, if property present */
+	if (device_property_present(dev, "adi,led-polarity")) {
+		ret = device_property_read_u32(dev, "adi,led-polarity", &val);
+		if (ret)  {
+			return ret;
+		} else if (val > 1) {
+			phydev_err(phydev, "invalid adi,led-polarity\n");
+			return -EINVAL;
+		}
+
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1,
+				     ADIN1300_LED_A_INV_EN_REG,
+				     ADIN1300_LED_A_INV_EN, val);
+		if (ret)
+			return ret;
+	}
+
+	/* set link-status polarity, default to active-high (0) */
+	if (device_property_present(dev, "adi,link-st-polarity")) {
+		ret = device_property_read_u32(dev, "adi,link-st-polarity", &val);
+		if (ret) {
+			return ret;
+		} else if (val > 1) {
+			phydev_err(phydev, "invalid adi,link-st-polarity\n");
+			return -EINVAL;
+		}
+	} else {
+		val = 0;
+	}
+
+	ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1,
+			     ADIN1300_GE_LNK_STAT_INV_EN_REG,
+			     ADIN1300_GE_LNK_STAT_INV_EN, val);
+
+	return ret;
+}
+
 static int adin_config_init(struct phy_device *phydev)
 {
 	int rc;
@@ -548,6 +597,10 @@ static int adin_config_init(struct phy_device *phydev)
 	if (rc < 0)
 		return rc;
 
+	rc = adin_config_pin_polarity(phydev);
+	if (rc < 0)
+		return rc;
+
 	phydev_dbg(phydev, "PHY is using mode '%s'\n",
 		   phy_modes(phydev->interface));
 

-- 
2.35.3


Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ