| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240426132258.oe5kif4yoca2yujh@jaunt>
Date: Fri, 26 Apr 2024 08:22:58 -0500
From: Nishanth Menon <nm@...com>
To: Robert Nelson <robertcnelson@...il.com>
CC: <linux-arm-kernel@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
<devicetree@...r.kernel.org>, Andrew Davis <afd@...com>,
Jared McArthur
<j-mcarthur@...com>,
Jason Kridner <jkridner@...gleboard.org>,
Deepak Khatri
<lorforlinux@...gleboard.org>,
Drew Fustini <drew@...gleboard.org>
Subject: Re: [PATCH v2 2/2] arm64: dts: ti: Add k3-am67a-beagley-ai
On 11:28-20240425, Robert Nelson wrote:
> BeagleBoard.org BeagleY-AI is an easy to use, affordable open source
> hardware single board computer based on the Texas Instruments AM67A,
> which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose
> digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),
> GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5
> cores for low-power, low-latency GPIO control.
>
> https://beagley-ai.org/
> https://openbeagle.org/beagley-ai/beagley-ai
>
> Signed-off-by: Robert Nelson <robertcnelson@...il.com>
> CC: Andrew Davis <afd@...com>
> CC: Nishanth Menon <nm@...com>
> CC: Jared McArthur <j-mcarthur@...com>
> CC: Jason Kridner <jkridner@...gleboard.org>
> CC: Deepak Khatri <lorforlinux@...gleboard.org>
> CC: Drew Fustini <drew@...gleboard.org>
> ---
A few cosmetic comments to fix up for the next rev:
> Changes since v1:
> - fixed incorrect vdd-3v3-sd-pins-default name
> - updated hdmi VDD_1V2 regulator for production pcb
> - switched device tree name from k3-j722s-beagley-ai to k3-am67a-beagley-ai
> - removed cpsw_port2 node
> - enable UHS support for MMCSD
> ---
> arch/arm64/boot/dts/ti/Makefile | 1 +
> .../arm64/boot/dts/ti/k3-am67a-beagley-ai.dts | 369 ++++++++++++++++++
> 2 files changed, 370 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 9a722c2473fb..a61e8902a23d 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -95,6 +95,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
>
> # Boards with J722s SoC
> +dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
>
> # Boards with J784s4 SoC
> diff --git a/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts
> new file mode 100644
> index 000000000000..cffa1c9ba00d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts
> @@ -0,0 +1,369 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * https://beagley-ai.org/
> + *
> + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
> + * Copyright (C) 2024 Robert Nelson, BeagleBoard.org Foundation
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "k3-j722s.dtsi"
> +
> +/ {
> + compatible = "beagle,am67a-beagley-ai", "ti,j722s";
> + model = "BeagleBoard.org BeagleY-AI";
> +
> + aliases {
> + serial0 = &wkup_uart0;
> + serial2 = &main_uart0;
> + mmc0 = &sdhci1;
> + };
> +
> + chosen {
> + stdout-path = &main_uart0;
> + };
> +
> + memory@...00000 {
> + /* 4G RAM */
> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> + <0x00000008 0x80000000 0x00000000 0x80000000>;
> + device_type = "memory";
> + bootph-pre-ram;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secure_tfa_ddr: tfa@...80000 {
> + reg = <0x00 0x9e780000 0x00 0x80000>;
> + no-map;
> + };
> +
> + secure_ddr: optee@...00000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>;
> + no-map;
> + };
> +
> + wkup_r5fss0_core0_memory_region: r5f-memory@...00000 {
> + compatible = "shared-dma-pool";
> + reg = <0x00 0xa0100000 0x00 0xf00000>;
> + no-map;
> + };
> +
> + };
> +
> + vsys_5v0: regulator-1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + bootph-all;
> + };
> +
> + vdd_3v3: regulator-2 {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vsys_5v0>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: regulator-mmc1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_3v3_sd_pins_default>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + gpio = <&main_gpio1 50 GPIO_ACTIVE_HIGH>;
> + bootph-all;
> + };
> +
> + vdd_sd_dv: regulator-TLV71033 {
> + compatible = "regulator-gpio";
> + regulator-name = "tlv71033";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_5v0>;
> + gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
you will need bootph-all; here.
> + };
> +
> + vsys_io_1v8: regulator-vsys-io-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_io_1v2: regulator-vsys-io-1v2 {
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_io_1v2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&main_pmx0 {
> +
> + main_i2c0_pins_default: main-i2c0-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D23) I2C0_SCL */
> + J722S_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (B22) I2C0_SDA */
> + >;
> + bootph-all;
> + };
> +
> + main_uart0_pins_default: main-uart0-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x01c8, PIN_INPUT, 0) /* (A22) UART0_RXD */
> + J722S_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (B22) UART0_TXD */
> + >;
> + bootph-all;
> + };
> +
> + vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x0244, PIN_OUTPUT, 7) /* (A24) MMC1_SDWP.GPIO1_49 */
> + >;
> + bootph-all;
> + };
> +
> + main_mmc1_pins_default: main-mmc1-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x023c, PIN_INPUT, 0) /* (H22) MMC1_CMD */
> + J722S_IOPAD(0x0234, PIN_OUTPUT, 0) /* (H24) MMC1_CLK */
> + J722S_IOPAD(0x0230, PIN_INPUT, 0) /* (H23) MMC1_DAT0 */
> + J722S_IOPAD(0x022c, PIN_INPUT_PULLUP, 0) /* (H20) MMC1_DAT1 */
> + J722S_IOPAD(0x0228, PIN_INPUT_PULLUP, 0) /* (J23) MMC1_DAT2 */
> + J722S_IOPAD(0x0224, PIN_INPUT_PULLUP, 0) /* (H25) MMC1_DAT3 */
> + J722S_IOPAD(0x0240, PIN_INPUT, 0) /* (B24) MMC1_SDCD */
I suggest using GPIO mode 7 here. (and see below):
J722S_IOPAD(0x0240, PIN_INPUT, 7) /* (B24) MMC1_SDCD */
you can optionally enable debounce as well if that is useful.
> + >;
> + bootph-all;
> + };
> +
> + mdio_pins_default: mdio-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AC24) MDIO0_MDC */
> + J722S_IOPAD(0x015c, PIN_INPUT, 0) /* (AD25) MDIO0_MDIO */
> + >;
> + };
> +
> + rgmii1_pins_default: rgmii1-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x014c, PIN_INPUT, 0) /* (AC25) RGMII1_RD0 */
> + J722S_IOPAD(0x0150, PIN_INPUT, 0) /* (AD27) RGMII1_RD1 */
> + J722S_IOPAD(0x0154, PIN_INPUT, 0) /* (AE24) RGMII1_RD2 */
> + J722S_IOPAD(0x0158, PIN_INPUT, 0) /* (AE26) RGMII1_RD3 */
> + J722S_IOPAD(0x0148, PIN_INPUT, 0) /* (AE27) RGMII1_RXC */
> + J722S_IOPAD(0x0144, PIN_INPUT, 0) /* (AD23) RGMII1_RX_CTL */
> + J722S_IOPAD(0x0134, PIN_OUTPUT, 0) /* (AF27) RGMII1_TD0 */
> + J722S_IOPAD(0x0138, PIN_OUTPUT, 0) /* (AE23) RGMII1_TD1 */
> + J722S_IOPAD(0x013c, PIN_OUTPUT, 0) /* (AG25) RGMII1_TD2 */
> + J722S_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AF24) RGMII1_TD3 */
> + J722S_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AG26) RGMII1_TXC */
> + J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
> + >;
> + };
> +
> + pmic_irq_pins_default: pmic-irq-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (B23) EXTINTn */
> + >;
> + };
> +
> + vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x0254, PIN_OUTPUT, 7) /* (E25) USB0_DRVVBUS.GPIO1_50 */
> + >;
> + };
> +};
> +
> +&cpsw3g {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii1_pins_default>, <&gbe_pmx_obsclk>;
> +
> + assigned-clocks = <&k3_clks 227 0>;
> + assigned-clock-parents = <&k3_clks 227 6>;
Here and elsewhere: status is last in the list. Please follow the
recommendations in:
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> +};
> +
> +&cpsw3g_mdio {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mdio_pins_default>;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> +
> + cpsw3g_phy0: ethernet-phy@0 {
> + reg = <0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + };
> +};
> +
> +&cpsw_port1 {
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&cpsw3g_phy0>;
> + status = "okay";
> +};
> +
> +&main_gpio1 {
> + status = "okay";
> +};
> +
> +&main_uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart0_pins_default>;
> + status = "okay";
> + bootph-all;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> +};
> +
> +&mcu_pmx0 {
> +
> + wkup_uart0_pins_default: wkup-uart0-default-pins {
> + pinctrl-single,pins = <
> + J722S_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C7) WKUP_UART0_CTSn */
> + J722S_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (C6) WKUP_UART0_RTSn */
> + J722S_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (D8) WKUP_UART0_RXD */
> + J722S_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (D7) WKUP_UART0_TXD */
> + >;
> + bootph-all;
> + };
> +
> + wkup_i2c0_pins_default: wkup-i2c0-default-pins {
> + pinctrl-single,pins = <
> + J722S_MCU_IOPAD(0x04c, PIN_INPUT_PULLUP, 0) /* (C7) WKUP_I2C0_SCL */
> + J722S_MCU_IOPAD(0x050, PIN_INPUT_PULLUP, 0) /* (C6) WKUP_I2C1_SDA */
> + >;
> + bootph-all;
> + };
> +
> + gbe_pmx_obsclk: gbe-pmx-obsclk-default-pins {
> + pinctrl-single,pins = <
> + J722S_MCU_IOPAD(0x0004, PIN_OUTPUT, 1) /* (A10) MCU_SPI0_CS1.MCU_OBSCLK0 */
> + >;
> + };
> +};
> +
> +&wkup_uart0 {
> + /* WKUP UART0 is used by Device Manager firmware */
> + pinctrl-names = "default";
> + pinctrl-0 = <&wkup_uart0_pins_default>;
> + status = "reserved";
> + bootph-all;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> +};
> +
> +&wkup_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&wkup_i2c0_pins_default>;
> + clock-frequency = <400000>;
> + status = "okay";
> + bootph-all;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> +
> + tps65219: pmic@30 {
> + bootph-all;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> + compatible = "ti,tps65219";
> + reg = <0x30>;
> + buck1-supply = <&vsys_5v0>;
> + buck2-supply = <&vsys_5v0>;
> + buck3-supply = <&vsys_5v0>;
> + ldo1-supply = <&vdd_3v3>;
> + ldo3-supply = <&vdd_3v3>;
> + ldo4-supply = <&vdd_3v3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_irq_pins_default>;
> + interrupt-parent = <&gic500>;
> + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + system-power-controller;
> + ti,power-button;
> +
> + regulators {
> + buck1_reg: buck1 {
> + regulator-name = "VDD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck2_reg: buck2 {
> + regulator-name = "VDD_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck3_reg: buck3 {
> + /* Regulator is left as is unused */
> + };
> +
> + ldo1_reg: ldo1 {
> + regulator-name = "VDDSHV5_SDIO";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-allow-bypass;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-name = "VDD_1V2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: ldo3 {
> + regulator-name = "VDDA_PHY_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + regulator-name = "VDDA_PLL_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&sdhci1 {
> + /* SD/MMC */
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> + status = "okay";
> + bootph-all;
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
Also add:
cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
cd-debounce-delay-ms = <100>;
ti,fails-without-test-cd;
With this, you will actually have runtime PM working properly for SD
card while booting off some other interface (e.g. nvme or others) and
card detect will work since GPIO based wake sequence will still be
valid.
> +};
> --
> 2.39.2
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Powered by blists - more mailing lists