| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZjzhOOSWE4pY1wEY@lizhi-Precision-Tower-5810>
Date: Thu, 9 May 2024 10:44:08 -0400
From: Frank Li <Frank.li@....com>
To: Richard Zhu <hongxing.zhu@....com>
Cc: conor@...nel.org, vkoul@...nel.org, kishon@...nel.org,
robh+dt@...nel.org, krzysztof.kozlowski+dt@...aro.org,
conor+dt@...nel.org, linux-phy@...ts.infradead.org,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org, kernel@...gutronix.de,
imx@...ts.linux.dev
Subject: Re: [PATCH v4 3/3] phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY
driver support
On Thu, May 09, 2024 at 01:56:21PM +0800, Richard Zhu wrote:
> Add i.MX8QM HSIO PHY driver support.
>
> i.MX8QM HSIO has three lane PHY instances, and can be bound to the
> following controllers in the different use cases listed in below table.
> - two lanes capable PCIEA controller.
> - one lane PCIEB controller.
> - AHCI SATA controller.
>
> i.MX8QM HSIO PHYs support the following use cases.
> +----------------------------------------------------+
> | | Lane0| Lane1| Lane2|
> |-------------------------------|------|------|------|
> | use case 1: PCIEAX2SATA | PCIEA| PCIEA| SATA |
> |-------------------------------|------|------|------|
> | use case 2: PCIEAX2PCIEB | PCIEA| PCIEA| PCIEB|
> |-------------------------------|------|------|------|
> | use case 3: PCIEAPCIEBSATA | PCIEA| PCIEB| SATA |
> +----------------------------------------------------+
>
> Signed-off-by: Richard Zhu <hongxing.zhu@....com>
> ---
> drivers/phy/freescale/Kconfig | 8 +
> drivers/phy/freescale/Makefile | 1 +
> drivers/phy/freescale/phy-fsl-imx8qm-hsio.c | 598 ++++++++++++++++++++
> 3 files changed, 607 insertions(+)
> create mode 100644 drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
>
> diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> index 853958fb2c06..c9ee48aeea9e 100644
> --- a/drivers/phy/freescale/Kconfig
> +++ b/drivers/phy/freescale/Kconfig
> @@ -35,6 +35,14 @@ config PHY_FSL_IMX8M_PCIE
> Enable this to add support for the PCIE PHY as found on
> i.MX8M family of SOCs.
>
> +config PHY_FSL_IMX8QM_HSIO
> + tristate "Freescale i.MX8QM HSIO PHY"
> + depends on OF && HAS_IOMEM
> + select GENERIC_PHY
> + help
> + Enable this to add support for the HSIO PHY as found on
> + i.MX8QM family of SOCs.
> +
> endif
>
> config PHY_FSL_LYNX_28G
> diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
> index cedb328bc4d2..b56b4d5c18ea 100644
> --- a/drivers/phy/freescale/Makefile
> +++ b/drivers/phy/freescale/Makefile
> @@ -3,4 +3,5 @@ obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
> obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o
> +obj-$(CONFIG_PHY_FSL_IMX8QM_HSIO) += phy-fsl-imx8qm-hsio.o
> obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o
> diff --git a/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
> new file mode 100644
> index 000000000000..90b57a6893c9
> --- /dev/null
> +++ b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
> @@ -0,0 +1,598 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2024 NXP
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/pci_regs.h>
> +#include <linux/phy/phy.h>
> +#include <linux/phy/pcie.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +#define MAX_NUM_LANE 3
> +#define LANE_NUM_CLKS 5
> +
> +/* Parameters for the waiting for PCIe PHY PLL to lock */
> +#define PHY_INIT_WAIT_USLEEP_MAX 10
> +#define PHY_INIT_WAIT_TIMEOUT (1000 * PHY_INIT_WAIT_USLEEP_MAX)
> +
> +/* i.MX8Q HSIO registers */
> +#define HSIO_CTRL0 0x0
> +#define HSIO_APB_RSTN_0 BIT(0)
> +#define HSIO_APB_RSTN_1 BIT(1)
> +#define HSIO_PIPE_RSTN_0_MASK GENMASK(25, 24)
> +#define HSIO_PIPE_RSTN_1_MASK GENMASK(27, 26)
> +#define HSIO_MODE_MASK GENMASK(20, 17)
> +#define HSIO_MODE_PCIE 0x0
> +#define HSIO_MODE_SATA 0x4
> +#define HSIO_DEVICE_TYPE_MASK GENMASK(27, 24)
> +#define HSIO_EPCS_TXDEEMP BIT(5)
> +#define HSIO_EPCS_TXDEEMP_SEL BIT(6)
> +#define HSIO_EPCS_PHYRESET_N BIT(7)
> +#define HSIO_RESET_N BIT(12)
> +
> +#define HSIO_IOB_RXENA BIT(0)
> +#define HSIO_IOB_TXENA BIT(1)
> +#define HSIO_IOB_A_0_TXOE BIT(2)
> +#define HSIO_IOB_A_0_M1M0_2 BIT(4)
> +#define HSIO_IOB_A_0_M1M0_MASK GENMASK(4, 3)
> +#define HSIO_PHYX1_EPCS_SEL BIT(12)
> +#define HSIO_PCIE_AB_SELECT BIT(13)
> +
> +#define HSIO_PHY_STS0 0x4
> +#define HSIO_LANE0_TX_PLL_LOCK BIT(4)
> +#define HSIO_LANE1_TX_PLL_LOCK BIT(12)
> +
> +#define HSIO_CTRL2 0x8
> +#define HSIO_LTSSM_ENABLE BIT(4)
> +#define HSIO_BUTTON_RST_N BIT(21)
> +#define HSIO_PERST_N BIT(22)
> +#define HSIO_POWER_UP_RST_N BIT(23)
> +
> +#define HSIO_PCIE_STS0 0xc
> +#define HSIO_PM_REQ_CORE_RST BIT(19)
> +
> +#define HSIO_REG48_PMA_STATUS 0x30
> +#define HSIO_REG48_PMA_RDY BIT(7)
> +
> +struct imx_hsio_drvdata {
> + int lane_num;
> +};
> +
> +struct imx_hsio_lane {
> + u32 ctrl_index;
> + u32 ctrl_off;
> + u32 idx;
> + u32 phy_off;
> + u32 phy_type;
> + const char * const *clk_names;
> + struct clk_bulk_data clks[LANE_NUM_CLKS];
> + struct imx_hsio_priv *priv;
> + struct phy *phy;
> + enum phy_mode phy_mode;
> +};
> +
> +struct imx_hsio_priv {
> + void __iomem *base;
> + struct device *dev;
> + atomic_t open_cnt;
> + const char *refclk_pad;
> + u32 hsio_cfg;
> + struct regmap *phy;
> + struct regmap *ctrl;
> + struct regmap *misc;
> + const struct imx_hsio_drvdata *drvdata;
> + struct imx_hsio_lane lane[MAX_NUM_LANE];
> +};
> +
> +static const char * const lan0_pcie_clks[] = {"apb_pclk0", "pclk0", "ctl0_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan1_pciea_clks[] = {"apb_pclk1", "pclk1", "ctl0_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan1_pcieb_clks[] = {"apb_pclk1", "pclk1", "ctl1_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan2_pcieb_clks[] = {"apb_pclk2", "pclk2", "ctl1_crr",
> + "phy1_crr", "misc_crr"};
> +static const char * const lan2_sata_clks[] = {"pclk2", "epcs_tx", "epcs_rx",
> + "phy1_crr", "misc_crr"};
> +
> +static const struct regmap_config regmap_config = {
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> +};
> +
> +static int imx_hsio_init(struct phy *phy)
> +{
> + int ret, i;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> + struct device *dev = priv->dev;
> +
> + /* Assign clocks refer to different modes */
> + switch (lane->phy_type) {
> + case PHY_TYPE_PCIE:
> + lane->phy_mode = PHY_MODE_PCIE;
> + if (lane->ctrl_index == 0) { /* PCIEA */
> + lane->ctrl_off = 0;
> + lane->phy_off = 0;
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++) {
> + if (lane->idx == 0)
> + lane->clks[i].id = lan0_pcie_clks[i];
> + else
> + lane->clks[i].id = lan1_pciea_clks[i];
> + }
> + } else { /* PCIEB */
> + if (lane->idx == 0) { /* i.MX8QXP */
> + lane->ctrl_off = 0;
> + lane->phy_off = 0;
> + } else {
> + /*
> + * On i.MX8QM, only second or third lane can be
> + * bound to PCIEB.
> + */
> + lane->ctrl_off = SZ_64K;
> + if (lane->idx == 1)
> + lane->phy_off = 0;
> + else /* the third lane is bound to PCIEB */
> + lane->phy_off = SZ_64K;
> + }
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++) {
> + if (lane->idx == 1)
> + lane->clks[i].id = lan1_pcieb_clks[i];
> + else if (lane->idx == 2)
> + lane->clks[i].id = lan2_pcieb_clks[i];
> + else /* i.MX8QXP only has PCIEB, idx is 0 */
> + lane->clks[i].id = lan0_pcie_clks[i];
> + }
> + }
> + break;
> + case PHY_TYPE_SATA:
> + /* On i.MX8QM, only the third lane can be bound to SATA */
> + lane->phy_mode = PHY_MODE_SATA;
> + lane->ctrl_off = SZ_128K;
> + lane->phy_off = SZ_64K;
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++)
> + lane->clks[i].id = lan2_sata_clks[i];
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /* Fetch clocks and enable them */
> + ret = devm_clk_bulk_get(dev, LANE_NUM_CLKS, lane->clks);
> + if (ret)
> + return ret;
> + ret = clk_bulk_prepare_enable(LANE_NUM_CLKS, lane->clks);
> + if (ret)
> + return ret;
> +
> + /* allow the clocks to stabilize */
> + usleep_range(200, 500);
> + return 0;
> +}
> +
> +static int imx_hsio_exit(struct phy *phy)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> +
> + clk_bulk_disable_unprepare(LANE_NUM_CLKS, lane->clks);
> +
> + return 0;
> +}
> +
> +static void imx_hsio_pcie_phy_resets(struct phy *phy)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_BUTTON_RST_N);
> + regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_PERST_N);
> + regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_POWER_UP_RST_N);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_BUTTON_RST_N);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_PERST_N);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_POWER_UP_RST_N);
> +
> + if (lane->idx == 1) {
> + regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_1);
> + regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_1_MASK);
> + } else {
> + regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_0);
> + regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_0_MASK);
> + }
> +}
> +
> +static void imx_hsio_sata_phy_resets(struct phy *phy)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + /* clear PHY RST, then set it */
> + regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_PHYRESET_N);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_PHYRESET_N);
> +
> + /* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
> + udelay(1);
> + regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_RESET_N);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
> +}
> +
> +static void imx_hsio_configure_clk_pad(struct phy *phy)
> +{
> + bool pll = false;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + if (strncmp(priv->refclk_pad, "output", 6) == 0) {
> + pll = true;
> + regmap_update_bits(priv->misc, HSIO_CTRL0,
> + HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_MASK,
> + HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_2);
> + } else {
> + regmap_update_bits(priv->misc, HSIO_CTRL0,
> + HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_MASK,
> + 0);
> + }
> +
> + regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_RXENA,
> + pll ? 0 : HSIO_IOB_RXENA);
> + regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_TXENA,
> + pll ? HSIO_IOB_TXENA : 0);
> +}
> +
> +static void imx_hsio_pre_set(struct phy *phy)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + atomic_set(&priv->open_cnt, 1);
> + if (priv->hsio_cfg & IMX8Q_HSIO_CFG_PCIEAX2PCIEB)
> + regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PCIE_AB_SELECT);
> + if (priv->hsio_cfg & IMX8Q_HSIO_CFG_PCIEAX2SATA)
> + regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PHYX1_EPCS_SEL);
> +
> + imx_hsio_configure_clk_pad(phy);
> +}
> +
> +static int imx_hsio_pcie_power_on(struct phy *phy)
> +{
> + int ret;
> + u32 val, addr, cond;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + imx_hsio_pcie_phy_resets(phy);
> +
> + /* Toggle apb_pclk to make sure PM_REQ_CORE_RST is cleared. */
> + clk_disable_unprepare(lane->clks[0].clk);
> + mdelay(1);
> + ret = clk_prepare_enable(lane->clks[0].clk);
> + if (ret) {
> + dev_err(priv->dev, "unable to enable phy apb_pclk\n");
> + return ret;
> + }
> +
> + addr = lane->ctrl_off + HSIO_PCIE_STS0;
> + cond = HSIO_PM_REQ_CORE_RST;
> + ret = regmap_read_poll_timeout(priv->ctrl, addr, val,
> + (val & cond) == 0,
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT);
> + if (ret)
> + dev_err(priv->dev, "HSIO_PM_REQ_CORE_RST is set\n");
> + return ret;
> +}
> +
> +static int imx_hsio_sata_power_on(struct phy *phy)
> +{
> + int ret;
> + u32 val, cond;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0, HSIO_APB_RSTN_0);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP);
> + regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP_SEL);
> +
> + imx_hsio_sata_phy_resets(phy);
> +
> + cond = HSIO_REG48_PMA_RDY;
> + ret = read_poll_timeout(readb, val, ((val & cond) == cond),
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT, false,
> + priv->base + HSIO_REG48_PMA_STATUS);
> + if (ret)
> + dev_err(priv->dev, "PHY calibration is timeout\n");
> + else
> + dev_dbg(priv->dev, "PHY calibration is done\n");
> +
> + return ret;
> +}
> +
> +static int imx_hsio_power_on(struct phy *phy)
> +{
> + int ret;
> + u32 val, cond;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + if (atomic_inc_and_test(&priv->open_cnt))
> + imx_hsio_pre_set(phy);
when multi client try power_on at the same time, it need wait first
imx_hsio_pre_set(phy) finish. So atomic is not enough here.
scope_guard(mutex, &priv->lock) {
if (!priv->open_cnt)
imx_hsio_pre_set(phy);
priv->open_cnt ++
}
in power_off function
scope_gard(mutex, &priv->lock) {
priv->open_cnt --;
}
> +
> + if (lane->phy_mode == PHY_MODE_PCIE)
> + ret = imx_hsio_pcie_power_on(phy);
> + else /* SATA */
> + ret = imx_hsio_sata_power_on(phy);
> + if (ret)
> + return ret;
> +
> + /* Polling to check the PHY is ready or not. */
> + if (lane->idx == 1)
> + cond = HSIO_LANE1_TX_PLL_LOCK;
> + else
> + /*
> + * Except the phy_off, the bit-offset of lane2 is same to lane0.
> + * Merge the lane0 and lane2 bit-operations together.
> + */
> + cond = HSIO_LANE0_TX_PLL_LOCK;
> +
> + ret = regmap_read_poll_timeout(priv->phy, lane->phy_off + HSIO_PHY_STS0,
> + val, ((val & cond) == cond),
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT);
> + if (ret) {
> + dev_err(priv->dev, "IMX8Q PHY%d PLL lock timeout\n", lane->idx);
> + return ret;
> + }
> + dev_dbg(priv->dev, "IMX8Q PHY%d PLL is locked\n", lane->idx);
> +
> + return ret;
> +}
> +
> +static int imx_hsio_power_off(struct phy *phy)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + if (atomic_dec_and_test(&priv->open_cnt)) {
> + atomic_set(&priv->open_cnt, -1);
> + regmap_clear_bits(priv->misc, HSIO_CTRL0, HSIO_PCIE_AB_SELECT);
> + regmap_clear_bits(priv->misc, HSIO_CTRL0, HSIO_PHYX1_EPCS_SEL);
> +
> + if (lane->phy_mode == PHY_MODE_PCIE) {
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL2,
> + HSIO_BUTTON_RST_N);
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL2,
> + HSIO_PERST_N);
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL2,
> + HSIO_POWER_UP_RST_N);
> + } else {
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP);
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP_SEL);
> + regmap_clear_bits(priv->ctrl,
> + lane->ctrl_off + HSIO_CTRL0,
> + HSIO_RESET_N);
> + }
> +
> + if (lane->idx == 1) {
> + regmap_clear_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_1);
> + regmap_clear_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_1_MASK);
> + } else {
> + /*
> + * Except the phy_off, the bit-offset of lane2 is same
> + * to lane0. Merge the lane0 and lane2 bit-operations
> + * together.
> + */
> + regmap_clear_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_0);
> + regmap_clear_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_0_MASK);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int imx_hsio_set_mode(struct phy *phy, enum phy_mode mode,
> + int submode)
> +{
> + u32 val;
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + if (lane->phy_mode != mode)
> + return -EINVAL;
> +
> + val = (mode == PHY_MODE_PCIE) ? HSIO_MODE_PCIE : HSIO_MODE_SATA;
> + val = FIELD_PREP(HSIO_MODE_MASK, val);
> + regmap_update_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
> + HSIO_MODE_MASK, val);
> +
> + switch (submode) {
> + case PHY_MODE_PCIE_RC:
> + val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ROOT_PORT);
> + break;
> + case PHY_MODE_PCIE_EP:
> + val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ENDPOINT);
> + break;
> + default: /* Support only PCIe EP and RC now. */
> + return 0;
> + }
> + if (submode)
> + regmap_update_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
> + HSIO_DEVICE_TYPE_MASK, val);
> +
> + return 0;
> +}
> +
> +static int imx_hsio_set_speed(struct phy *phy, int speed)
> +{
> + struct imx_hsio_lane *lane = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = lane->priv;
> +
> + regmap_update_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
> + HSIO_LTSSM_ENABLE,
> + speed ? HSIO_LTSSM_ENABLE : 0);
> + return 0;
> +}
> +
> +static const struct phy_ops imx_hsio_ops = {
> + .init = imx_hsio_init,
> + .exit = imx_hsio_exit,
> + .power_on = imx_hsio_power_on,
> + .power_off = imx_hsio_power_off,
> + .set_mode = imx_hsio_set_mode,
> + .set_speed = imx_hsio_set_speed,
> + .owner = THIS_MODULE,
> +};
> +
> +static const struct imx_hsio_drvdata imx8qxp_hsio_drvdata = {
> + .lane_num = 0x1,
> +};
> +
> +static const struct imx_hsio_drvdata imx_hsio_drvdata = {
> + .lane_num = 0x3,
> +};
> +
> +static const struct of_device_id imx_hsio_of_match[] = {
> + {.compatible = "fsl,imx8qm-hsio", .data = &imx_hsio_drvdata},
> + {.compatible = "fsl,imx8qxp-hsio", .data = &imx8qxp_hsio_drvdata},
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, imx_hsio_of_match);
> +
> +static struct phy *imx_hsio_xlate(struct device *dev,
> + const struct of_phandle_args *args)
> +{
> + struct imx_hsio_priv *priv = dev_get_drvdata(dev);
> + int idx = args->args[0];
> + int phy_type = args->args[1];
> + int ctrl_index = args->args[2];
> +
> + if (idx < 0 || idx >= priv->drvdata->lane_num)
> + return ERR_PTR(-EINVAL);
> + priv->lane[idx].idx = idx;
> + priv->lane[idx].phy_type = phy_type;
> + priv->lane[idx].ctrl_index = ctrl_index;
> +
> + return priv->lane[idx].phy;
> +}
> +
> +static int imx_hsio_probe(struct platform_device *pdev)
> +{
> + int i;
> + void __iomem *off;
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + struct imx_hsio_priv *priv;
> + struct phy_provider *provider;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> + priv->dev = &pdev->dev;
> + priv->drvdata = of_device_get_match_data(dev);
> + atomic_set(&priv->open_cnt, -1);
> +
> + /* Get HSIO configuration mode */
> + if (of_property_read_u32(np, "fsl,hsio-cfg", &priv->hsio_cfg))
> + priv->hsio_cfg = 0;
> + /* Get PHY refclk pad mode */
> + if (of_property_read_string(np, "fsl,refclk-pad-mode",
> + &priv->refclk_pad))
> + priv->refclk_pad = NULL;
> +
> + priv->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "phy");
> + priv->phy = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->phy))
> + return dev_err_probe(dev, PTR_ERR(priv->phy),
> + "unable to find phy csr registers\n");
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "ctrl");
> + priv->ctrl = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->ctrl))
> + return dev_err_probe(dev, PTR_ERR(priv->ctrl),
> + "unable to find ctrl csr registers\n");
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "misc");
> + priv->misc = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->misc))
> + return dev_err_probe(dev, PTR_ERR(priv->misc),
> + "unable to find misc csr registers\n");
> +
> + for (i = 0; i < priv->drvdata->lane_num; i++) {
> + struct imx_hsio_lane *lane = &priv->lane[i];
> + struct phy *phy;
> +
> + memset(lane, 0, sizeof(*lane));
> +
> + phy = devm_phy_create(&pdev->dev, NULL, &imx_hsio_ops);
> + if (IS_ERR(phy))
> + return PTR_ERR(phy);
> +
> + lane->priv = priv;
> + lane->phy = phy;
> + lane->idx = i;
> + phy_set_drvdata(phy, lane);
> + }
> +
> + dev_set_drvdata(dev, priv);
> + dev_set_drvdata(&pdev->dev, priv);
> +
> + provider = devm_of_phy_provider_register(&pdev->dev, imx_hsio_xlate);
> +
> + return PTR_ERR_OR_ZERO(provider);
> +}
> +
> +static struct platform_driver imx_hsio_driver = {
> + .probe = imx_hsio_probe,
> + .driver = {
> + .name = "imx8qm-hsio-phy",
> + .of_match_table = imx_hsio_of_match,
> + }
> +};
> +module_platform_driver(imx_hsio_driver);
> +
> +MODULE_DESCRIPTION("FSL IMX8QM HSIO SERDES PHY driver");
> +MODULE_LICENSE("GPL");
> --
> 2.37.1
>
Powered by blists - more mailing lists