| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240531-iio-adc-ref-supply-refactor-v1-1-4b313c0615ad@baylibre.com>
Date: Fri, 31 May 2024 16:19:32 -0500
From: David Lechner <dlechner@...libre.com>
To: Jonathan Cameron <jic23@...nel.org>
Cc: David Lechner <dlechner@...libre.com>,
Marcelo Schmitt <marcelo.schmitt1@...il.com>,
Nuno Sá <nuno.sa@...log.com>,
Michael Hennerich <Michael.Hennerich@...log.com>,
Mark Brown <broonie@...nel.org>,
Liam Girdwood <lgirdwood@...il.com>,
linux-iio@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH 1/5] iio: adc: ad7192: use devm_regulator_get_enable_read_voltage
This makes use of the new devm_regulator_get_enable_read_voltage()
function to reduce boilerplate code.
Error messages have changed slightly since there are now fewer places
where we print an error. The rest of the logic of selecting which
supply to use as the reference voltage remains the same.
Also 1000 is replaced by MILLI in a few places for consistency.
Signed-off-by: David Lechner <dlechner@...libre.com>
---
drivers/iio/adc/ad7192.c | 98 +++++++++++++++++-------------------------------
1 file changed, 35 insertions(+), 63 deletions(-)
diff --git a/drivers/iio/adc/ad7192.c b/drivers/iio/adc/ad7192.c
index 0789121236d6..e08bf066b3f6 100644
--- a/drivers/iio/adc/ad7192.c
+++ b/drivers/iio/adc/ad7192.c
@@ -200,8 +200,6 @@ struct ad7192_chip_info {
struct ad7192_state {
const struct ad7192_chip_info *chip_info;
- struct regulator *avdd;
- struct regulator *vref;
struct clk *mclk;
u16 int_vref_mv;
u32 aincom_mv;
@@ -1189,17 +1187,11 @@ static const struct ad7192_chip_info ad7192_chip_info_tbl[] = {
},
};
-static void ad7192_reg_disable(void *reg)
-{
- regulator_disable(reg);
-}
-
static int ad7192_probe(struct spi_device *spi)
{
struct ad7192_state *st;
struct iio_dev *indio_dev;
- struct regulator *aincom;
- int ret;
+ int ret, avdd_mv;
if (!spi->irq) {
dev_err(&spi->dev, "no IRQ?\n");
@@ -1219,74 +1211,54 @@ static int ad7192_probe(struct spi_device *spi)
* Newer firmware should provide a zero volt fixed supply if wired to
* ground.
*/
- aincom = devm_regulator_get_optional(&spi->dev, "aincom");
- if (IS_ERR(aincom)) {
- if (PTR_ERR(aincom) != -ENODEV)
- return dev_err_probe(&spi->dev, PTR_ERR(aincom),
- "Failed to get AINCOM supply\n");
-
+ ret = devm_regulator_get_enable_read_voltage(&spi->dev, "aincom");
+ if (ret == -ENODEV)
st->aincom_mv = 0;
- } else {
- ret = regulator_enable(aincom);
- if (ret)
- return dev_err_probe(&spi->dev, ret,
- "Failed to enable specified AINCOM supply\n");
+ else if (ret < 0)
+ return dev_err_probe(&spi->dev, ret, "Failed to get AINCOM voltage\n");
+ else
+ st->aincom_mv = ret / MILLI;
- ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, aincom);
+ /* AVDD can optionally be used as reference voltage */
+ ret = devm_regulator_get_enable_read_voltage(&spi->dev, "avdd");
+ if (ret == -EINVAL) {
+ /*
+ * We get -EINVAL if avdd is a supply with unknown voltage. We
+ * still need to enable it since it is also a power supply.
+ */
+ ret = devm_regulator_get_enable(&spi->dev, "avdd");
if (ret)
- return ret;
-
- ret = regulator_get_voltage(aincom);
- if (ret < 0)
return dev_err_probe(&spi->dev, ret,
- "Device tree error, AINCOM voltage undefined\n");
- st->aincom_mv = ret / MILLI;
- }
+ "Failed to enable AVDD supply\n");
- st->avdd = devm_regulator_get(&spi->dev, "avdd");
- if (IS_ERR(st->avdd))
- return PTR_ERR(st->avdd);
-
- ret = regulator_enable(st->avdd);
- if (ret) {
- dev_err(&spi->dev, "Failed to enable specified AVdd supply\n");
- return ret;
+ avdd_mv = 0;
+ } else if (ret < 0) {
+ return dev_err_probe(&spi->dev, ret, "Failed to get AVDD voltage\n");
+ } else {
+ avdd_mv = ret / MILLI;
}
- ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->avdd);
- if (ret)
- return ret;
ret = devm_regulator_get_enable(&spi->dev, "dvdd");
if (ret)
return dev_err_probe(&spi->dev, ret, "Failed to enable specified DVdd supply\n");
- st->vref = devm_regulator_get_optional(&spi->dev, "vref");
- if (IS_ERR(st->vref)) {
- if (PTR_ERR(st->vref) != -ENODEV)
- return PTR_ERR(st->vref);
-
- ret = regulator_get_voltage(st->avdd);
- if (ret < 0)
- return dev_err_probe(&spi->dev, ret,
- "Device tree error, AVdd voltage undefined\n");
+ /*
+ * This is either REFIN1 or REFIN2 depending on adi,refin2-pins-enable.
+ * If this supply is not present, fall back to AVDD as reference.
+ */
+ ret = devm_regulator_get_enable_read_voltage(&spi->dev, "vref");
+ if (ret == -ENODEV) {
+ if (avdd_mv == 0)
+ return dev_err_probe(&spi->dev, -ENODEV,
+ "No reference voltage available\n");
+
+ st->int_vref_mv = avdd_mv;
+ } else if (ret < 0) {
+ return ret;
} else {
- ret = regulator_enable(st->vref);
- if (ret) {
- dev_err(&spi->dev, "Failed to enable specified Vref supply\n");
- return ret;
- }
-
- ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->vref);
- if (ret)
- return ret;
-
- ret = regulator_get_voltage(st->vref);
- if (ret < 0)
- return dev_err_probe(&spi->dev, ret,
- "Device tree error, Vref voltage undefined\n");
+ st->int_vref_mv = ret / MILLI;
}
- st->int_vref_mv = ret / 1000;
st->chip_info = spi_get_device_match_data(spi);
indio_dev->name = st->chip_info->name;
--
2.45.1
Powered by blists - more mailing lists