Message-ID: <e340f48324b0ea3afb1c715cb2fba184c27112a1.1717539384.git.marcelo.schmitt@analog.com>
Date: Wed, 5 Jun 2024 08:14:50 -0300
From: Marcelo Schmitt <marcelo.schmitt@...log.com>
To: <broonie@...nel.org>, <lars@...afoo.de>, <Michael.Hennerich@...log.com>,
        <jic23@...nel.org>, <robh+dt@...nel.org>,
        <krzysztof.kozlowski+dt@...aro.org>, <conor+dt@...nel.org>,
        <nuno.sa@...log.com>, <dlechner@...libre.com>,
        <marcelo.schmitt1@...il.com>
CC: <linux-iio@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-spi@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH v3 6/6] iio: adc: Add support for AD4000

Add support for AD4000 series of low noise, low power, high speed,
successive aproximation register (SAR) ADCs.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt@...log.com>
---
 MAINTAINERS              |   1 +
 drivers/iio/adc/Kconfig  |  12 +
 drivers/iio/adc/Makefile |   1 +
 drivers/iio/adc/ad4000.c | 735 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 749 insertions(+)
 create mode 100644 drivers/iio/adc/ad4000.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 1f052b9cd912..c732cf13f511 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1206,6 +1206,7 @@ L:	linux-iio@...r.kernel.org
 S:	Supported
 W:	https://ez.analog.com/linux-software-drivers
 F:	Documentation/devicetree/bindings/iio/adc/adi,ad4000.yaml
+F:	drivers/iio/adc/ad4000.c
 
 ANALOG DEVICES INC AD4130 DRIVER
 M:	Cosmin Tanislav <cosmin.tanislav@...log.com>
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 5030319249c5..dcc49d9711a4 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -21,6 +21,18 @@ config AD_SIGMA_DELTA
 	select IIO_BUFFER
 	select IIO_TRIGGERED_BUFFER
 
+config AD4000
+	tristate "Analog Devices AD4000 ADC Driver"
+	depends on SPI
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	  Say yes here to build support for Analog Devices AD4000 high speed
+	  SPI analog to digital converters (ADC).
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ad4000.
+
 config AD4130
 	tristate "Analog Device AD4130 ADC Driver"
 	depends on SPI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 37ac689a0209..c32bd0ef6128 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -6,6 +6,7 @@
 # When adding new entries keep the list in alphabetical order
 obj-$(CONFIG_AB8500_GPADC) += ab8500-gpadc.o
 obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o
+obj-$(CONFIG_AD4000) += ad4000.o
 obj-$(CONFIG_AD4130) += ad4130.o
 obj-$(CONFIG_AD7091R) += ad7091r-base.o
 obj-$(CONFIG_AD7091R5) += ad7091r5.o
diff --git a/drivers/iio/adc/ad4000.c b/drivers/iio/adc/ad4000.c
new file mode 100644
index 000000000000..55dc36fbd549
--- /dev/null
+++ b/drivers/iio/adc/ad4000.c
@@ -0,0 +1,735 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AD4000 SPI ADC driver
+ *
+ * Copyright 2024 Analog Devices Inc.
+ */
+#include <asm/unaligned.h>
+#include <linux/bits.h>
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/math.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <linux/sysfs.h>
+#include <linux/units.h>
+#include <linux/util_macros.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
+
+#define AD4000_READ_COMMAND	0x54
+#define AD4000_WRITE_COMMAND	0x14
+
+#define AD4000_CONFIG_REG_MSK	0xFF
+
+/* AD4000 Configuration Register programmable bits */
+#define AD4000_CFG_STATUS		BIT(4) /* Status bits output */
+#define AD4000_CFG_SPAN_COMP		BIT(3) /* Input span compression  */
+#define AD4000_CFG_HIGHZ		BIT(2) /* High impedance mode  */
+#define AD4000_CFG_TURBO		BIT(1) /* Turbo mode */
+
+#define AD4000_TQUIET1_NS		190
+#define AD4000_TQUIET2_NS		60
+#define AD4000_TCONV_NS			320
+
+#define AD4000_18BIT_MSK	GENMASK(31, 14)
+#define AD4000_20BIT_MSK	GENMASK(31, 12)
+
+#define AD4000_DIFF_CHANNEL(_sign, _real_bits)				\
+	{								\
+		.type = IIO_VOLTAGE,					\
+		.indexed = 1,						\
+		.differential = 1,					\
+		.channel = 0,						\
+		.channel2 = 1,						\
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |		\
+				      BIT(IIO_CHAN_INFO_SCALE),		\
+		.info_mask_separate_available = BIT(IIO_CHAN_INFO_SCALE),\
+		.scan_type = {						\
+			.sign = _sign,					\
+			.realbits = _real_bits,				\
+			.storagebits = _real_bits > 16 ? 32 : 16,	\
+			.shift = _real_bits > 16 ? 32 - _real_bits : 0,	\
+			.endianness = IIO_BE,				\
+		},							\
+	}								\
+
+#define AD4000_PSEUDO_DIFF_CHANNEL(_sign, _real_bits)			\
+	{								\
+		.type = IIO_VOLTAGE,					\
+		.indexed = 1,						\
+		.channel = 0,						\
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |		\
+				      BIT(IIO_CHAN_INFO_SCALE) |	\
+				      BIT(IIO_CHAN_INFO_OFFSET),	\
+		.info_mask_separate_available = BIT(IIO_CHAN_INFO_SCALE),\
+		.scan_type = {						\
+			.sign = _sign,					\
+			.realbits = _real_bits,				\
+			.storagebits = _real_bits > 16 ? 32 : 16,	\
+			.shift = _real_bits > 16 ? 32 - _real_bits : 0,	\
+			.endianness = IIO_BE,				\
+		},							\
+	}								\
+
+enum ad4000_ids {
+	ID_AD4000,
+	ID_AD4001,
+	ID_AD4002,
+	ID_AD4003,
+	ID_AD4004,
+	ID_AD4005,
+	ID_AD4006,
+	ID_AD4007,
+	ID_AD4008,
+	ID_AD4010,
+	ID_AD4011,
+	ID_AD4020,
+	ID_AD4021,
+	ID_AD4022,
+	ID_ADAQ4001,
+	ID_ADAQ4003,
+};
+
+enum ad4000_spi_mode {
+	/* datasheet calls this "4-wire mode" (controller CS goes to ADC SDI!) */
+	AD4000_SPI_MODE_DEFAULT,
+	/* datasheet calls this "3-wire mode" (not related to SPI_3WIRE!) */
+	AD4000_SPI_MODE_SINGLE,
+};
+
+/* maps adi,spi-mode property value to enum */
+static const char * const ad4000_spi_modes[] = {
+	[AD4000_SPI_MODE_DEFAULT] = "",
+	[AD4000_SPI_MODE_SINGLE] = "single",
+};
+
+struct ad4000_chip_info {
+	const char *dev_name;
+	struct iio_chan_spec chan_spec;
+};
+
+static const struct ad4000_chip_info ad4000_chips[] = {
+	[ID_AD4000] = {
+		.dev_name = "ad4000",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 16),
+	},
+	[ID_AD4001] = {
+		.dev_name = "ad4001",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 16),
+	},
+	[ID_AD4002] = {
+		.dev_name = "ad4002",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 18),
+	},
+	[ID_AD4003] = {
+		.dev_name = "ad4003",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 18),
+	},
+	[ID_AD4004] = {
+		.dev_name = "ad4004",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 16),
+	},
+	[ID_AD4005] = {
+		.dev_name = "ad4005",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 16),
+	},
+	[ID_AD4006] = {
+		.dev_name = "ad4006",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 18),
+	},
+	[ID_AD4007] = {
+		.dev_name = "ad4007",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 18),
+	},
+	[ID_AD4008] = {
+		.dev_name = "ad4008",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 16),
+	},
+	[ID_AD4010] = {
+		.dev_name = "ad4010",
+		.chan_spec = AD4000_PSEUDO_DIFF_CHANNEL('u', 18),
+	},
+	[ID_AD4011] = {
+		.dev_name = "ad4011",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 18),
+	},
+	[ID_AD4020] = {
+		.dev_name = "ad4020",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 20),
+	},
+	[ID_AD4021] = {
+		.dev_name = "ad4021",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 20),
+	},
+	[ID_AD4022] = {
+		.dev_name = "ad4022",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 20),
+	},
+	[ID_ADAQ4001] = {
+		.dev_name = "adaq4001",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 16),
+	},
+	[ID_ADAQ4003] = {
+		.dev_name = "adaq4003",
+		.chan_spec = AD4000_DIFF_CHANNEL('s', 18),
+	},
+};
+
+struct ad4000_state {
+	struct spi_device *spi;
+	struct gpio_desc *cnv_gpio;
+	struct spi_transfer xfers[2];
+	struct spi_message msg;
+	int vref;
+	enum ad4000_spi_mode spi_mode;
+	bool span_comp;
+	bool turbo_mode;
+	int gain_milli;
+	int scale_tbl[2][2];
+
+	/*
+	 * DMA (thus cache coherency maintenance) requires the
+	 * transfer buffers to live in their own cache lines.
+	 */
+	struct {
+		union {
+			__be16 sample_buf16;
+			__be32 sample_buf32;
+		} data;
+		s64 timestamp __aligned(8);
+	} scan __aligned(IIO_DMA_MINALIGN);
+	__be16 tx_buf;
+	__be16 rx_buf;
+};
+
+static void ad4000_fill_scale_tbl(struct ad4000_state *st, int scale_bits,
+				  const struct ad4000_chip_info *chip)
+{
+	int diff = chip->chan_spec.differential;
+	int val, val2, tmp0, tmp1;
+	u64 tmp2;
+
+	val2 = scale_bits;
+	val = st->vref / 1000;
+	/*
+	 * The gain is stored as a fraction of 1000 and, as we need to
+	 * divide vref by gain, we invert the gain/1000 fraction.
+	 * Also multiply by an extra MILLI to avoid losing precision.
+	 */
+	val = mult_frac(val, MILLI * MILLI, st->gain_milli);
+	/* Would multiply by NANO here but we multiplied by extra MILLI */
+	tmp2 = shift_right((u64)val * MICRO, val2);
+	tmp0 = (int)div_s64_rem(tmp2, NANO, &tmp1);
+	/* Store scale for when span compression is disabled */
+	st->scale_tbl[0][0] = tmp0; /* Integer part */
+	st->scale_tbl[0][1] = abs(tmp1); /* Fractional part */
+	/* Store scale for when span compression is enabled */
+	st->scale_tbl[1][0] = tmp0;
+	/* The integer part is always zero so don't bother to divide it. */
+	if (diff)
+		st->scale_tbl[1][1] = DIV_ROUND_CLOSEST(abs(tmp1) * 4, 5);
+	else
+		st->scale_tbl[1][1] = DIV_ROUND_CLOSEST(abs(tmp1) * 9, 10);
+}
+
+static int ad4000_write_reg(struct ad4000_state *st, uint8_t val)
+{
+	st->tx_buf = cpu_to_be16(AD4000_WRITE_COMMAND << BITS_PER_BYTE | val);
+	return spi_write(st->spi, &st->tx_buf, 2);
+}
+
+static int ad4000_read_reg(struct ad4000_state *st, unsigned int *val)
+{
+	struct spi_transfer t[] = {
+		{
+			.tx_buf = &st->tx_buf,
+			.rx_buf = &st->rx_buf,
+			.len = 2,
+		},
+	};
+	int ret;
+
+	st->tx_buf = cpu_to_be16(AD4000_READ_COMMAND << BITS_PER_BYTE);
+	ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t));
+	if (ret < 0)
+		return ret;
+
+	*val = be16_to_cpu(st->rx_buf);
+
+	return ret;
+}
+
+static void ad4000_unoptimize_msg(void *msg)
+{
+	spi_unoptimize_message(msg);
+}
+
+/*
+ * This executes a data sample transfer for when the device connections are
+ * in "3-wire" mode, selected by setting the adi,spi-mode device tree property
+ * to "single". In this connection mode, the ADC SDI pin is connected to MOSI or
+ * to VIO and ADC CNV pin is connected either to a SPI controller CS or to a GPIO.
+ * AD4000 series of devices initiate conversions on the rising edge of CNV pin.
+ *
+ * If the CNV pin is connected to an SPI controller CS line (which is by default
+ * active low), the ADC readings would have a latency (delay) of one read.
+ * Moreover, since we also do ADC sampling for filling the buffer on triggered
+ * buffer mode, the timestamps of buffer readings would be disarranged.
+ * To prevent the read latency and reduce the time discrepancy between the
+ * sample read request and the time of actual sampling by the ADC, do a
+ * preparatory transfer to pulse the CS/CNV line.
+ */
+static int ad4000_prepare_3wire_mode_message(struct ad4000_state *st,
+					     const struct iio_chan_spec *chan)
+{
+	unsigned int cnv_pulse_time = st->turbo_mode ? AD4000_TQUIET1_NS
+						     : AD4000_TCONV_NS;
+	struct spi_transfer *xfers = st->xfers;
+	int ret;
+
+	xfers[0].cs_change = 1;
+	xfers[0].cs_change_delay.value = cnv_pulse_time;
+	xfers[0].cs_change_delay.unit = SPI_DELAY_UNIT_NSECS;
+
+	xfers[1].rx_buf = &st->scan.data;
+	xfers[1].len = BITS_TO_BYTES(chan->scan_type.storagebits);
+	xfers[1].delay.value = AD4000_TQUIET2_NS;
+	xfers[1].delay.unit = SPI_DELAY_UNIT_NSECS;
+
+	spi_message_init_with_transfers(&st->msg, st->xfers, 2);
+
+	ret = spi_optimize_message(st->spi, &st->msg);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(&st->spi->dev, ad4000_unoptimize_msg,
+					&st->msg);
+}
+
+/*
+ * This executes a data sample transfer for when the device connections are
+ * in "4-wire" mode, selected when the adi,spi-mode device tree
+ * property is absent or empty. In this connection mode, the controller CS pin
+ * is connected to ADC SDI pin and a GPIO is connected to ADC CNV pin.
+ * The GPIO connected to ADC CNV pin is set outside of the SPI transfer.
+ */
+static int ad4000_prepare_4wire_mode_message(struct ad4000_state *st,
+					     const struct iio_chan_spec *chan)
+{
+	unsigned int cnv_to_sdi_time = st->turbo_mode ? AD4000_TQUIET1_NS
+						      : AD4000_TCONV_NS;
+	struct spi_transfer *xfers = st->xfers;
+	int ret;
+
+	/*
+	 * Dummy transfer to cause enough delay between CNV going high and SDI
+	 * going low.
+	 */
+	xfers[0].cs_off = 1;
+	xfers[0].delay.value = cnv_to_sdi_time;
+	xfers[0].delay.unit = SPI_DELAY_UNIT_NSECS;
+
+	xfers[1].rx_buf = &st->scan.data;
+	xfers[1].len = BITS_TO_BYTES(chan->scan_type.storagebits);
+
+	spi_message_init_with_transfers(&st->msg, st->xfers, 2);
+
+	ret = spi_optimize_message(st->spi, &st->msg);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(&st->spi->dev, ad4000_unoptimize_msg,
+					&st->msg);
+}
+
+static int ad4000_convert_and_acquire(struct ad4000_state *st)
+{
+	int ret;
+
+	/*
+	 * In 4-wire mode, the CNV line is held high for the entire conversion
+	 * and acquisition process. In other modes st->cnv_gpio is NULL and is
+	 * ignored (CS is wired to CNV in those cases).
+	 */
+	gpiod_set_value_cansleep(st->cnv_gpio, 1);
+	ret = spi_sync(st->spi, &st->msg);
+	gpiod_set_value_cansleep(st->cnv_gpio, 0);
+
+	return ret;
+}
+
+static int ad4000_single_conversion(struct iio_dev *indio_dev,
+				    const struct iio_chan_spec *chan, int *val)
+{
+	struct ad4000_state *st = iio_priv(indio_dev);
+	u32 sample;
+	int ret;
+
+	ret = ad4000_convert_and_acquire(st);
+
+	if (chan->scan_type.storagebits > 16)
+		sample = be32_to_cpu(st->scan.data.sample_buf32);
+	else
+		sample = be16_to_cpu(st->scan.data.sample_buf16);
+
+	switch (chan->scan_type.realbits) {
+	case 16:
+		break;
+	case 18:
+		sample = FIELD_GET(AD4000_18BIT_MSK, sample);
+		break;
+	case 20:
+		sample = FIELD_GET(AD4000_20BIT_MSK, sample);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (chan->scan_type.sign == 's')
+		*val = sign_extend32(sample, chan->scan_type.realbits - 1);
+
+	return IIO_VAL_INT;
+}
+
+static int ad4000_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan, int *val,
+			   int *val2, long info)
+{
+	struct ad4000_state *st = iio_priv(indio_dev);
+
+	switch (info) {
+	case IIO_CHAN_INFO_RAW:
+		iio_device_claim_direct_scoped(return -EBUSY, indio_dev)
+			return ad4000_single_conversion(indio_dev, chan, val);
+		unreachable();
+	case IIO_CHAN_INFO_SCALE:
+		*val = st->scale_tbl[st->span_comp][0];
+		*val2 = st->scale_tbl[st->span_comp][1];
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_OFFSET:
+		*val = 0;
+		if (st->span_comp)
+			*val = mult_frac(st->vref / 1000, 1, 10);
+
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ad4000_read_avail(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     const int **vals, int *type, int *length,
+			     long info)
+{
+	struct ad4000_state *st = iio_priv(indio_dev);
+
+	switch (info) {
+	case IIO_CHAN_INFO_SCALE:
+		*vals = (int *)st->scale_tbl;
+		*length = 2 * 2;
+		*type = IIO_VAL_INT_PLUS_NANO;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ad4000_write_raw_get_fmt(struct iio_dev *indio_dev,
+				    struct iio_chan_spec const *chan, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		return IIO_VAL_INT_PLUS_NANO;
+	default:
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+}
+
+static int ad4000_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan, int val, int val2,
+			    long mask)
+{
+	struct ad4000_state *st = iio_priv(indio_dev);
+	unsigned int reg_val;
+	bool span_comp_en;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		iio_device_claim_direct_scoped(return -EBUSY, indio_dev) {
+			ret = ad4000_read_reg(st, &reg_val);
+			if (ret < 0)
+				return ret;
+
+			span_comp_en = (val2 == st->scale_tbl[1][1]);
+			reg_val &= ~AD4000_CFG_SPAN_COMP;
+			reg_val |= FIELD_PREP(AD4000_CFG_SPAN_COMP, span_comp_en);
+
+			ret = ad4000_write_reg(st, reg_val);
+			if (ret < 0)
+				return ret;
+
+			st->span_comp = span_comp_en;
+			return 0;
+		}
+		unreachable();
+	default:
+		return -EINVAL;
+	}
+}
+
+static irqreturn_t ad4000_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct ad4000_state *st = iio_priv(indio_dev);
+	int ret;
+
+	ret = ad4000_convert_and_acquire(st);
+	if (ret < 0)
+		goto err_out;
+
+	iio_push_to_buffers_with_timestamp(indio_dev, &st->scan,
+					   iio_get_time_ns(indio_dev));
+
+err_out:
+	iio_trigger_notify_done(indio_dev->trig);
+	return IRQ_HANDLED;
+}
+
+static int ad4000_reg_access(struct iio_dev *indio_dev, unsigned int reg,
+			     unsigned int writeval, unsigned int *readval)
+{
+	struct ad4000_state *st = iio_priv(indio_dev);
+	int ret;
+
+	if (readval)
+		ret = ad4000_read_reg(st, readval);
+	else
+		ret = ad4000_write_reg(st, writeval);
+
+	return ret;
+}
+
+static const struct iio_info ad4000_info = {
+	.read_raw = &ad4000_read_raw,
+	.read_avail = &ad4000_read_avail,
+	.write_raw = &ad4000_write_raw,
+	.write_raw_get_fmt = &ad4000_write_raw_get_fmt,
+	.debugfs_reg_access = &ad4000_reg_access,
+
+};
+
+static int ad4000_config(struct ad4000_state *st)
+{
+	unsigned int reg_val;
+
+	if (device_property_present(&st->spi->dev, "adi,high-z-input"))
+		reg_val |= FIELD_PREP(AD4000_CFG_HIGHZ, 1);
+
+	/*
+	 * The ADC SDI pin might be connected to controller CS line in which
+	 * case the write might fail. This, however, does not prevent the device
+	 * from functioning even though in a configuration other than the
+	 * requested one.
+	 */
+	return ad4000_write_reg(st, reg_val);
+}
+
+static void ad4000_regulator_disable(void *reg)
+{
+	regulator_disable(reg);
+}
+
+static int ad4000_probe(struct spi_device *spi)
+{
+	const struct ad4000_chip_info *chip;
+	struct regulator *vref_reg;
+	struct iio_dev *indio_dev;
+	struct ad4000_state *st;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	chip = spi_get_device_match_data(spi);
+	if (!chip)
+		return -EINVAL;
+
+	st = iio_priv(indio_dev);
+	st->spi = spi;
+
+	ret = devm_regulator_get_enable(&spi->dev, "vdd");
+	if (ret)
+		return dev_err_probe(&spi->dev, ret, "Failed to enable VDD supply\n");
+
+	ret = devm_regulator_get_enable(&spi->dev, "vio");
+	if (ret)
+		return dev_err_probe(&spi->dev, ret, "Failed to enable VIO supply\n");
+
+	vref_reg = devm_regulator_get(&spi->dev, "ref");
+	if (IS_ERR(vref_reg))
+		return dev_err_probe(&spi->dev, PTR_ERR(vref_reg),
+				     "Failed to get vref regulator\n");
+
+	ret = regulator_enable(vref_reg);
+	if (ret < 0)
+		return dev_err_probe(&spi->dev, ret,
+				     "Failed to enable voltage regulator\n");
+
+	ret = devm_add_action_or_reset(&spi->dev, ad4000_regulator_disable, vref_reg);
+	if (ret)
+		return dev_err_probe(&spi->dev, ret,
+				     "Failed to add regulator disable action\n");
+
+	st->vref = regulator_get_voltage(vref_reg);
+	if (st->vref < 0)
+		return dev_err_probe(&spi->dev, st->vref, "Failed to get vref\n");
+
+	st->cnv_gpio = devm_gpiod_get_optional(&spi->dev, "cnv", GPIOD_OUT_HIGH);
+	if (IS_ERR(st->cnv_gpio))
+		return dev_err_probe(&spi->dev, PTR_ERR(st->cnv_gpio),
+				     "Failed to get CNV GPIO");
+
+	ret = device_property_match_property_string(&spi->dev, "adi,spi-mode",
+						    ad4000_spi_modes,
+						    ARRAY_SIZE(ad4000_spi_modes));
+	/* Default to 4-wire mode if adi,spi-mode property is not present */
+	if (ret == -EINVAL)
+		st->spi_mode = AD4000_SPI_MODE_DEFAULT;
+	else if (ret < 0)
+		return dev_err_probe(&spi->dev, ret,
+				     "getting adi,spi-mode property failed\n");
+	else
+		st->spi_mode = ret;
+
+	switch (st->spi_mode) {
+	case AD4000_SPI_MODE_DEFAULT:
+		ret = ad4000_prepare_4wire_mode_message(st, &chip->chan_spec);
+		if (ret)
+			return ret;
+
+		break;
+	case AD4000_SPI_MODE_SINGLE:
+		ret = ad4000_prepare_3wire_mode_message(st, &chip->chan_spec);
+		if (ret)
+			return ret;
+
+		/*
+		 * In "3-wire mode", the ADC SDI line must be kept high when
+		 * data is not being clocked out of the controller.
+		 * Request the SPI controller to make MOSI idle high.
+		 */
+		spi->mode = SPI_MODE_0 | SPI_MOSI_IDLE_HIGH;
+		if (spi_setup(spi))
+			dev_warn(&st->spi->dev, "SPI controller setup failed\n");
+
+		break;
+	}
+
+	ret = ad4000_config(st);
+	if (ret < 0)
+		dev_dbg(&st->spi->dev, "Failed to config device\n");
+
+	indio_dev->name = chip->dev_name;
+	indio_dev->info = &ad4000_info;
+	indio_dev->channels = &chip->chan_spec;
+	indio_dev->num_channels = 1;
+
+	/* Hardware gain only applies to ADAQ devices */
+	st->gain_milli = 1000;
+	if (device_property_present(&spi->dev, "adi,gain-milli")) {
+
+		ret = device_property_read_u32(&spi->dev, "adi,gain-milli",
+					       &st->gain_milli);
+		if (ret)
+			return dev_err_probe(&spi->dev, ret,
+					     "Failed to read gain property\n");
+	}
+
+	/*
+	 * ADCs that output two's complement code have one less bit to express
+	 * voltage magnitude.
+	 */
+	if (chip->chan_spec.scan_type.sign == 's')
+		ad4000_fill_scale_tbl(st, chip->chan_spec.scan_type.realbits - 1,
+				      chip);
+	else
+		ad4000_fill_scale_tbl(st, chip->chan_spec.scan_type.realbits,
+				      chip);
+
+	ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev,
+					      &iio_pollfunc_store_time,
+					      &ad4000_trigger_handler, NULL);
+	if (ret)
+		return ret;
+
+	return devm_iio_device_register(&spi->dev, indio_dev);
+}
+
+static const struct spi_device_id ad4000_id[] = {
+	{ "ad4000", (kernel_ulong_t)&ad4000_chips[ID_AD4000] },
+	{ "ad4001", (kernel_ulong_t)&ad4000_chips[ID_AD4001] },
+	{ "ad4002", (kernel_ulong_t)&ad4000_chips[ID_AD4002] },
+	{ "ad4003", (kernel_ulong_t)&ad4000_chips[ID_AD4003] },
+	{ "ad4004", (kernel_ulong_t)&ad4000_chips[ID_AD4004] },
+	{ "ad4005", (kernel_ulong_t)&ad4000_chips[ID_AD4005] },
+	{ "ad4006", (kernel_ulong_t)&ad4000_chips[ID_AD4006] },
+	{ "ad4007", (kernel_ulong_t)&ad4000_chips[ID_AD4007] },
+	{ "ad4008", (kernel_ulong_t)&ad4000_chips[ID_AD4008] },
+	{ "ad4010", (kernel_ulong_t)&ad4000_chips[ID_AD4010] },
+	{ "ad4011", (kernel_ulong_t)&ad4000_chips[ID_AD4011] },
+	{ "ad4020", (kernel_ulong_t)&ad4000_chips[ID_AD4020] },
+	{ "ad4021", (kernel_ulong_t)&ad4000_chips[ID_AD4021] },
+	{ "ad4022", (kernel_ulong_t)&ad4000_chips[ID_AD4022] },
+	{ "adaq4001", (kernel_ulong_t)&ad4000_chips[ID_ADAQ4001] },
+	{ "adaq4003", (kernel_ulong_t)&ad4000_chips[ID_ADAQ4003] },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ad4000_id);
+
+static const struct of_device_id ad4000_of_match[] = {
+	{ .compatible = "adi,ad4000", .data = &ad4000_chips[ID_AD4000] },
+	{ .compatible = "adi,ad4001", .data = &ad4000_chips[ID_AD4001] },
+	{ .compatible = "adi,ad4002", .data = &ad4000_chips[ID_AD4002] },
+	{ .compatible = "adi,ad4003", .data = &ad4000_chips[ID_AD4003] },
+	{ .compatible = "adi,ad4004", .data = &ad4000_chips[ID_AD4004] },
+	{ .compatible = "adi,ad4005", .data = &ad4000_chips[ID_AD4005] },
+	{ .compatible = "adi,ad4006", .data = &ad4000_chips[ID_AD4006] },
+	{ .compatible = "adi,ad4007", .data = &ad4000_chips[ID_AD4007] },
+	{ .compatible = "adi,ad4008", .data = &ad4000_chips[ID_AD4008] },
+	{ .compatible = "adi,ad4010", .data = &ad4000_chips[ID_AD4010] },
+	{ .compatible = "adi,ad4011", .data = &ad4000_chips[ID_AD4011] },
+	{ .compatible = "adi,ad4020", .data = &ad4000_chips[ID_AD4020] },
+	{ .compatible = "adi,ad4021", .data = &ad4000_chips[ID_AD4021] },
+	{ .compatible = "adi,ad4022", .data = &ad4000_chips[ID_AD4022] },
+	{ .compatible = "adi,adaq4001", .data = &ad4000_chips[ID_ADAQ4001] },
+	{ .compatible = "adi,adaq4003", .data = &ad4000_chips[ID_ADAQ4003] },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ad4000_of_match);
+
+static struct spi_driver ad4000_driver = {
+	.driver = {
+		.name   = "ad4000",
+		.of_match_table = ad4000_of_match,
+	},
+	.probe          = ad4000_probe,
+	.id_table       = ad4000_id,
+};
+module_spi_driver(ad4000_driver);
+
+MODULE_AUTHOR("Marcelo Schmitt <marcelo.schmitt@...log.com>");
+MODULE_DESCRIPTION("Analog Devices AD4000 ADC driver");
+MODULE_LICENSE("GPL");
-- 
2.43.0

Powered by blists - more mailing lists