| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240613093706.480700-1-j-choudhary@ti.com>
Date: Thu, 13 Jun 2024 15:07:06 +0530
From: Jayesh Choudhary <j-choudhary@...com>
To: <linux-kernel@...r.kernel.org>, <nm@...com>, <vigneshr@...com>,
<a-bhatia1@...com>, <u-kumar1@...com>, <j-choudhary@...com>
CC: <kristo@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
<conor+dt@...nel.org>, <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>
Subject: [PATCH v2] arm64: dts: ti: k3-j721e: Add overlay for J721E Infotainment Expansion Board
From: Tomi Valkeinen <tomi.valkeinen@...com>
J721E common processor board can be interfaced with the infotainment
expansion board[0] to enable the following audio/video interfaces in
addition to the peripherals provided by the common processor board:
- Two Audio codecs each with three Stereo Inputs and four Stereo Outputs
- Audio input over FPD Link III
- Digital Audio Interface TX/RX
- HDMI/FPD LINK III Display out
- LI/OV Camera input
Add support for TFP410 HDMI bridge located on the Infotainment Expansion
Board (connected to J46 & J51).
Add a HDMI connector node and connect the endpoints as below:
DSS => TFP410 bridge => HDMI connector
Also add the pinmux data and board muxes for DPI.
Rest of the peripherals are not added as of now.
[0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@...com>
[j-choudhary@...com: minor cleanup]
Signed-off-by: Jayesh Choudhary <j-choudhary@...com>
---
Testlog:
<https://gist.github.com/Jayesh2000/45f75cf075cc969d1dfc9015c6f23fd4>
Changelog v1->v2:
- rebased on next-20240613
- add dtbo in ascending order in Makefile
- Mention in commit message that other peripherals on the expansion board
are not added as of now.
v1 patch:
<https://lore.kernel.org/all/20240227120310.661579-1-j-choudhary@ti.com/>
arch/arm64/boot/dts/ti/Makefile | 4 +
...-j721e-common-proc-board-infotainment.dtso | 164 ++++++++++++++++++
2 files changed, 168 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d956372a7163..5c6701897f31 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -83,6 +83,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
# Boards with J721e SoC
k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board-infotainment.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtbo
@@ -151,6 +152,8 @@ k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
+k3-j721e-common-proc-board-infotainment-dtbs := k3-j721e-common-proc-board.dtb \
+ k3-j721e-common-proc-board-infotainment.dtbo
k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \
k3-j721e-evm-pcie0-ep.dtbo
k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \
@@ -182,6 +185,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \
k3-am68-sk-base-board-csi2-dual-imx219.dtb \
k3-am69-sk-csi2-dual-imx219.dtb \
+ k3-j721e-common-proc-board-infotainment.dtb \
k3-j721e-evm-pcie0-ep.dtb \
k3-j721e-sk-csi2-dual-imx219.dtb \
k3-j721s2-evm-pcie1-ep.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso
new file mode 100644
index 000000000000..65a7e54f0884
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Infotainment Expansion Board for j721e-evm
+ * User Guide: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf>
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "k3-pinctrl.h"
+
+&{/} {
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+ type = "a";
+ ddc-i2c-bus = <&main_i2c1>;
+ digital;
+ /* P12 - HDMI_HPD */
+ hpd-gpios = <&exp6 10 GPIO_ACTIVE_HIGH>;
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+ };
+
+ dvi-bridge {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,tfp410";
+ /* P10 - HDMI_PDn */
+ powerdown-gpios = <&exp6 8 GPIO_ACTIVE_LOW>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint {
+ remote-endpoint = <&dpi_out0>;
+ pclk-sample = <1>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint {
+ remote-endpoint =
+ <&hdmi_connector_in>;
+ };
+ };
+ };
+};
+
+&main_pmx0 {
+ main_i2c1_exp6_pins_default: main-i2c1-exp6-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x264, PIN_INPUT, 7) /* (T29) MMC2_DAT2.GPIO1_24 */
+ >;
+ };
+
+ dss_vout0_pins_default: dss-vout0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */
+ J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */
+ J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */
+ J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */
+ J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */
+ J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */
+ J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */
+ J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */
+ J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */
+ J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */
+ J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */
+ J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */
+ J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */
+ J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */
+ J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */
+ J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */
+ J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */
+ J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */
+ J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */
+ J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */
+ J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */
+ J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */
+ J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */
+ J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */
+ J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */
+ J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */
+ J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */
+ >;
+ };
+};
+
+&exp1 {
+ p14-hog {
+ /* P14 - VINOUT_MUX_SEL0 */
+ gpio-hog;
+ gpios = <12 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "VINOUT_MUX_SEL0";
+ };
+
+ p15-hog {
+ /* P15 - VINOUT_MUX_SEL1 */
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "VINOUT_MUX_SEL1";
+ };
+};
+
+&main_i2c1 {
+ /* i2c1 is used for DVI DDC, so we need to use 100kHz */
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ exp6: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_exp6_pins_default>;
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ p11-hog {
+ /* P11 - HDMI_DDC_OE */
+ gpio-hog;
+ gpios = <9 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "HDMI_DDC_OE";
+ };
+ };
+};
+
+&dss {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_vout0_pins_default>;
+};
+
+&dss_ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ dpi_out0: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ };
+ };
+};
--
2.25.1
Powered by blists - more mailing lists