| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240616215354.40999-3-seb-dev@mail.de>
Date: Sun, 16 Jun 2024 23:48:30 +0200
From: Sebastian Kropatsch <seb-dev@...l.de>
To: Heiko Stuebner <heiko@...ech.de>
Cc: linux-rockchip@...ts.infradead.org,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Sebastian Reichel <sebastian.reichel@...labora.com>,
devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org,
Space Meyer <git@...-space.agency>
Subject: [PATCH 2/2] arm64: dts: rockchip: Add FriendlyElec CM3588 NAS board
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
To reflect the hardware setup, add device tree sources for the SoM and
the NAS daughter board as separate files.
Hardware features:
- Rockchip RK3588 SoC
- 4GB/8GB/16GB LPDDR4x RAM
- 64GB eMMC
- MicroSD card slot
- 1x RTL8125B 2.5G Ethernet
- 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs
- 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A
- 1x USB 3.0 Type-C with DP AltMode support
- 2x HDMI 2.1 out, 1x HDMI in
- MIPI-CSI Connector, MIPI-DSI Connector
- 40-pin GPIO header
- 4 buttons: power, reset, recovery, MASK, user button
- 3.5mm Headphone out, 2.0mm PH-2A Mic in
- 5V Fan connector, PWM beeper, IR receiver, RTC battery connector
PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1
speed. Data lane mapping in the DT is done like described in commit
f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588").
This device tree includes support for eMMC, SD card, ethernet, all USB2
and USB3 ports, all four M.2 slots, GPU, beeper, IR, RTC, UART debugging
as well as the buttons and LEDs.
The GPIOs are labeled according to the schematics.
Reviewed-by: Space Meyer <git@...-space.agency>
Signed-off-by: Sebastian Kropatsch <seb-dev@...l.de>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../rk3588-friendlyelec-cm3588-nas.dts | 778 ++++++++++++++++++
.../rockchip/rk3588-friendlyelec-cm3588.dtsi | 653 +++++++++++++++
3 files changed, 1432 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 22f7ba98175b..85d949f2c909 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -122,6 +122,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts
new file mode 100644
index 000000000000..83103e4c7216
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts
@@ -0,0 +1,778 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2023 Thomas McKahan
+ * Copyright (c) 2024 Sebastian Kropatsch
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3588-friendlyelec-cm3588.dtsi"
+
+/ {
+ model = "FriendlyElec CM3588 NAS";
+ compatible = "friendlyarm,cm3588-nas", "friendlyarm,cm3588", "rockchip,rk3588";
+
+ adc_key_recovery: adc-key-recovery {
+ compatible = "adc-keys";
+ io-channels = <&saradc 1>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <100>;
+
+ button-recovery {
+ label = "Recovery";
+ linux,code = <KEY_VENDOR>;
+ press-threshold-microvolt = <17000>;
+ };
+ };
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&headphone_detect>;
+
+ simple-audio-card,format = "i2s";
+ simple-audio-card,hp-det-gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_LOW>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,name = "realtek,rt5616-codec";
+
+ simple-audio-card,routing =
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "MIC1", "Microphone Jack",
+ "Microphone Jack", "micbias1";
+ simple-audio-card,widgets =
+ "Headphone", "Headphones",
+ "Microphone", "Microphone Jack";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s0_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rt5616>;
+ };
+ };
+
+ buzzer: pwm-beeper {
+ compatible = "pwm-beeper";
+ amp-supply = <&vcc_5v0_sys>;
+ beeper-hz = <500>;
+ pwms = <&pwm8 0 500000 0>;
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ #cooling-cells = <2>;
+ cooling-levels = <0 50 80 120 160 220>;
+ fan-supply = <&vcc_5v0_sys>;
+ pwms = <&pwm1 0 50000 0>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key1_pin>;
+
+ button-user {
+ debounce-interval = <50>;
+ gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>;
+ label = "User Button";
+ linux,code = <BTN_1>;
+ wakeup-source;
+ };
+ };
+
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_12v_dcin: regulator-vcc-12v-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_3v3_m2_a: regulator-vcc-3v3-m2-a {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_m2_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_12v_dcin>;
+ };
+
+ vcc_3v3_m2_b: regulator-vcc-3v3-m2-b {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_m2_b";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_12v_dcin>;
+ };
+
+ vcc_3v3_m2_c: regulator-vcc-3v3-m2-c {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_m2_c";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_12v_dcin>;
+ };
+
+ vcc_3v3_m2_d: regulator-vcc-3v3-m2-d {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_m2_d";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_12v_dcin>;
+ };
+
+ /* vcc_5v0_sys powers the peripherals */
+ vcc_5v0_sys: regulator-vcc-5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_12v_dcin>;
+ };
+
+ /* SY6280AAC power switch (U14 in schematics) */
+ vcc_5v0_host_20: regulator-vcc-5v0-host-20 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_5v0_host20_en>;
+ regulator-name = "vcc_5v0_host_20";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ /* SY6280AAC power switch (U8 in schematics) */
+ vcc_5v0_host_30_p1: regulator-vcc-5v0-host-30-p1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_5v0_host30p1_en>;
+ regulator-name = "vcc_5v0_host_30_p1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ /* SY6280AAC power switch (U9 in schematics) */
+ vcc_5v0_host_30_p2: regulator-vcc-5v0-host-30-p2 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_5v0_host30p2_en>;
+ regulator-name = "vcc_5v0_host_30_p2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ /* SY6280AAC power switch (U10 in schematics) */
+ vbus_5v0_typec: regulator-vbus-5v0-typec {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec_5v_pwr_en>;
+ regulator-name = "vbus_5v0_typec";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+};
+
+/* vcc_4v0_sys powers the RK806 and RK860's */
+&vcc_4v0_sys {
+ vin-supply = <&vcc_12v_dcin>;
+};
+
+/* Combo PHY 1 is configured to act as as PCIe 2.0 PHY */
+/* Used by PCIe controller 2 (pcie2x1l0) */
+&combphy1_ps {
+ status = "okay";
+};
+
+/* Combo PHY 2 is configured to act as USB3 PHY */
+/* Used by USB 3.0 OTG 2 controller (USB 3.0 Type-A port 2) */
+/* CM3588 USB Controller Config Table: USB30 HOST2 */
+&combphy2_psu {
+ status = "okay";
+};
+
+/* GPIO names are in the format "Human-readable-name [SIGNAL_LABEL]" */
+/* Signal labels match the official CM3588 NAS SDK schematic revision 2309 */
+&gpio0 {
+ gpio-line-names =
+ /* GPIO0 A0-A7 */
+ "", "", "", "",
+ "MicroSD detect [SDMMC_DET_L]", "", "", "",
+ /* GPIO0 B0-B7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO0 C0-C7 */
+ "", "", "", "",
+ "Pin 10 [UART0_RX_M0]", "Pin 08 [UART0_TX_M0/PWM4_M0]", "Pin 32 [PWM5_M1]", "",
+ /* GPIO0 D0-D7 */
+ "", "", "", "USB3 Type-C [CC_INT_L]",
+ "IR receiver [PWM3_IR_M0]", "User Button", "", "";
+};
+
+&gpio1 {
+ gpio-line-names =
+ /* GPIO1 A0-A7 */
+ "Pin 27 [UART6_RX_M1]", "Pin 28 [UART6_TX_M1]", "", "",
+ "USB2 Type-A [USB2_PWREN]", "", "", "Pin 15",
+ /* GPIO1 B0-B7 */
+ "Pin 26", "Pin 21 [SPI0_MISO_M2]", "Pin 19 [SPI0_MOSI_M2/UART4_RX_M2]", "Pin 23 [SPI0_CLK_M2/UART4_TX_M2]",
+ "Pin 24 [SPI0_CS0_M2/UART7_RX_M2]", "Pin 22 [SPI0_CS1_M0/UART7_TX_M2]", "", "CSI-Pin 14 [MIPI_CAM2_CLKOUT]",
+ /* GPIO1 C0-C7 */
+ "", "", "", "",
+ "Headphone detect [HP_DET_L]", "", "", "",
+ /* GPIO1 D0-D7 */
+ "", "", "USB3 Type-C [TYPEC5V_PWREN_H]", "5V Fan [PWM1_M1]",
+ "", "HDMI-in detect [HDMIIRX_DET_L]", "Pin 05 [I2C8_SCL_M2]", "Pin 03 [I2C8_SDA_M2]";
+};
+
+&gpio2 {
+ gpio-line-names =
+ /* GPIO2 A0-A7 */
+ "", "", "", "",
+ "", "", "SPI NOR Flash [FSPI_D0_M1]", "SPI NOR Flash [FSPI_D1_M1]",
+ /* GPIO2 B0-B7 */
+ "SPI NOR Flash [FSPI_D2_M1]", "SPI NOR Flash [FSPI_D3_M1]", "", "SPI NOR Flash [FSPI_CLK_M1]",
+ "SPI NOR Flash [FSPI_CSN0_M1]", "", "", "",
+ /* GPIO2 C0-C7 */
+ "", "CSI-Pin 11 [MIPI_CAM2_RESET_L]", "CSI-Pin 12 [MIPI_CAM2_PDN_L]", "",
+ "", "", "", "",
+ /* GPIO2 D0-D7 */
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ /* GPIO3 A0-A7 */
+ "Pin 35 [SPI4_MISO_M1/PWM10_M0]", "Pin 38 [SPI4_MOSI_M1]", "Pin 40 [SPI4_CLK_M1/UART8_TX_M1]", "Pin 36 [SPI4_CS0_M1/UART8_RX_M1]",
+ "Pin 37 [SPI4_CS1_M1]", "USB3-A #2 [USB3_2_PWREN]", "DSI-Pin 12 [LCD_RST]", "Buzzer [PWM8_M0]",
+ /* GPIO3 B0-B7 */
+ "Pin 33 [PWM9_M0]", "DSI-Pin 10 [PWM2_M1/LCD_BL]", "Pin 07", "Pin 16",
+ "Pin 18", "Pin 29 [UART3_TX_M1/PWM12_M0]", "Pin 31 [UART3_RX_M1/PWM13_M0]", "Pin 12",
+ /* GPIO3 C0-C7 */
+ "DSI-Pin 08 [TP_INT_L]", "DSI-Pin 14 [TP_RST_L]", "Pin 11 [PWM14_M0]", "Pin 13 [PWM15_IR_M0]",
+ "", "", "", "DSI-Pin 06 [I2C5_SCL_M0_TP]",
+ /* GPIO3 D0-D7 */
+ "DSI-Pin 05 [I2C5_SDA_M0_TP]", "", "", "",
+ "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ /* GPIO4 A0-A7 */
+ "", "", "M.2 M-Key Slot4 [M2_D_PERST_L]", "",
+ "", "", "", "",
+ /* GPIO4 B0-B7 */
+ "USB3-A #1 [USB3_TYPEC1_PWREN]", "", "", "M.2 M-Key Slot3 [M2_C_PERST_L]",
+ "M.2 M-Key Slot2 [M2_B_PERST_L]", "M.2 M-Key Slot1 [M2_A_CLKREQ_L]", "M.2 M-Key Slot1 [M2_A_PERST_L]", "",
+ /* GPIO4 C0-C7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO4 D0-D7 */
+ "", "", "", "",
+ "", "", "", "";
+};
+
+/* Connected to MIPI-DSI0 */
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5m0_xfer>;
+ status = "disabled";
+};
+
+&i2c6 {
+ fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus_5v0_typec>;
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USB-C";
+ power-role = "source";
+ source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "source";
+ vbus-supply = <&vbus_5v0_typec>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usbc0_role_sw: endpoint {
+ remote-endpoint = <&dwc3_0_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+};
+
+/* Connected to MIPI-CSI1 */
+/* &i2c7 */
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+&i2c8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8m2_xfer>;
+ status = "okay";
+};
+
+&pcie2x1l0 {
+ /* 2. M.2 socket, CON14: pcie30phy port0 lane1, @fe170000 */
+ max-link-speed = <3>;
+ num-lanes = <1>;
+ phys = <&pcie30phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_0_rst>;
+ reset-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_m2_b>;
+ status = "okay";
+};
+
+&pcie2x1l1 {
+ /* 4. M.2 socket, CON16: pcie30phy port1 lane1, @fe180000 */
+ max-link-speed = <3>;
+ num-lanes = <1>;
+ phys = <&pcie30phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_1_rst>;
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_m2_d>;
+ status = "okay";
+};
+
+&pcie30phy {
+ /*
+ * Data lane mapping <1 3 2 4> = x1x1 x1x1 (bifurcation of both ports)
+ * port 0 lane 0 - always mapped to controller 0 (4L)
+ * port 0 lane 1 - map to controller 2 (1L0)
+ * port 1 lane 0 - map to controller 1 (2L)
+ * port 1 lane 1 - map to controller 3 (1L1)
+ */
+ data-lanes = <1 3 2 4>;
+ status = "okay";
+};
+
+&pcie3x4 {
+ /* 1. M.2 socket, CON13: pcie30phy port0 lane0, @fe150000 */
+ max-link-speed = <3>;
+ num-lanes = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3x4_rst>;
+ reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_m2_a>;
+ status = "okay";
+};
+
+&pcie3x2 {
+ /* 3. M.2 socket, CON15: pcie30phy port1 lane0, @fe160000 */
+ max-link-speed = <3>;
+ num-lanes = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3x2_rst>;
+ reset-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_m2_c>;
+ status = "okay";
+};
+
+&pinctrl {
+ audio {
+ headphone_detect: headphone-detect {
+ rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ gpio-key {
+ key1_pin: key1-pin {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pcie {
+ pcie2_0_rst: pcie2-0-rst {
+ rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie2_1_rst: pcie2-1-rst {
+ rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie3x2_rst: pcie3x2-rst {
+ rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie3x4_rst: pcie3x4-rst {
+ rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ vcc_5v0_host20_en: vcc-5v0-host20-en {
+ rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc_5v0_host30p1_en: vcc-5v0-host30p1-en {
+ rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc_5v0_host30p2_en: vcc-5v0-host30p2-en {
+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-typec {
+ usbc0_int: usbc0-int {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ typec_5v_pwr_en: typec-5v-pwr-en {
+ rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+/* Connected to 5V Fan */
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1m1_pins>;
+ status = "okay";
+};
+
+/* Connected to MIPI-DSI0 */
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2m1_pins>;
+};
+
+/* Connected to IR Receiver */
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3m0_pins>;
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with UART0 */
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4m1_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+&pwm5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm5m1_pins>;
+ status = "okay";
+};
+
+/* Connected to Buzzer */
+&pwm8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm8m0_pins>;
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+&pwm9 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm9m0_pins>;
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with SPI4 */
+&pwm10 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm10m0_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with UART3 */
+&pwm12 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm12m0_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with UART3 */
+&pwm13 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm13m0_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+&pwm14 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm14m0_pins>;
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Optimized for infrared applications */
+&pwm15 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm15m0_pins>;
+ status = "disabled";
+};
+
+/* microSD card */
+&sdmmc {
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with UART4, UART7 and PWM10 */
+&spi0 {
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0m2_cs0 &spi0m2_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with UART8 */
+&spi4 {
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4m1_cs0 &spi4m1_pins>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with PWM4 */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0m0_xfer>;
+ status = "disabled";
+};
+
+/* Debug UART */
+&uart2 {
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with PWM12 and PWM13 */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3m1_xfer>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with SPI0 */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4m2_xfer>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart6m1_xfer>;
+ status = "okay";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with SPI0 */
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7m2_xfer>;
+ status = "disabled";
+};
+
+/* GPIO Connector, connected to 40-pin GPIO header */
+/* Shared with SPI4 */
+&uart8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart8m1_xfer>;
+ status = "disabled";
+};
+
+/* USB2 PHY for USB Type-C port */
+/* CM3588 USB Controller Config Table: USB20 OTG0 */
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vbus_5v0_typec>;
+ status = "okay";
+};
+
+/* USB2 PHY for USB 3.0 Type-A port 1 */
+/* CM3588 USB Controller Config Table: USB20 OTG1 */
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc_5v0_host_30_p1>;
+ status = "okay";
+};
+
+/* USB2 PHY for USB 2.0 Type-A */
+/* CM3588 USB Controller Config Table: USB20 HOST0 */
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ phy-supply = <&vcc_5v0_host_20>;
+ status = "okay";
+};
+
+/* USB2 PHY for USB 3.0 Type-A port 2 */
+/* CM3588 USB Controller Config Table: USB20 HOST1 */
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ phy-supply = <&vcc_5v0_host_30_p2>;
+ status = "okay";
+};
+
+/* USB 2.0 Type-A */
+/* PHY: <&u2phy2_host> */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+/* USB 2.0 Type-A */
+/* PHY: <&u2phy2_host> */
+&usb_host0_ohci {
+ status = "okay";
+};
+
+/* USB Type-C */
+/* PHYs: <&u2phy0_otg>, <&usbdp_phy0 PHY_TYPE_USB3> */
+&usb_host0_xhci {
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ dwc3_0_role_switch: endpoint {
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
+/* Lower USB 3.0 Type-A (port 2) */
+/* PHY: <&u2phy3_host> */
+&usb_host1_ehci {
+ status = "okay";
+};
+
+/* Lower USB 3.0 Type-A (port 2) */
+/* PHY: <&u2phy3_host> */
+&usb_host1_ohci {
+ status = "okay";
+};
+
+/* Upper USB 3.0 Type-A (port 1) */
+/* PHYs: <&u2phy1_otg>, <&usbdp_phy1 PHY_TYPE_USB3> */
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* Lower USB 3.0 Type-A (port 2) */
+/* PHYs: <&combphy2_psu PHY_TYPE_USB3> */
+&usb_host2_xhci {
+ status = "okay";
+};
+
+/* USB3 PHY for USB Type-C port */
+/* CM3588 USB Controller Config Table: USB30 OTG0 */
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
+/* USB3 PHY for USB 3.0 Type-A port 1 */
+/* CM3588 USB Controller Config Table: USB30 OTG1 */
+&usbdp_phy1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi
new file mode 100644
index 000000000000..e3a9598b99fc
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi
@@ -0,0 +1,653 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2023 Thomas McKahan
+ * Copyright (c) 2024 Sebastian Kropatsch
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3588.dtsi"
+
+/ {
+ model = "FriendlyElec CM3588";
+ compatible = "friendlyarm,cm3588", "rockchip,rk3588";
+
+ aliases {
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_sys: led-0 {
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_sys_pin>;
+ };
+
+ led_usr: led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_usr_pin>;
+ };
+ };
+
+ /* vcc_4v0_sys powers the RK806 and RK860's */
+ vcc_4v0_sys: regulator-vcc-4v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_4v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <4000000>;
+ };
+
+ vcc_3v3_pcie20: regulator-vcc-3v3-pcie20 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_pcie20";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_s3>;
+ };
+
+ vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
+ compatible = "regulator-fixed";
+ gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_s0_pwr>;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc_3v3_sd_s0";
+ vin-supply = <&vcc_3v3_s3>;
+ };
+
+ vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-1v1-nldo-s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc_4v0_sys>;
+ };
+};
+
+/* Combo PHY 0 is configured to act as as PCIe 2.0 PHY */
+/* Used by PCIe controller 4 (pcie2x1l2) */
+&combphy0_ps {
+ status = "okay";
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ sram-supply = <&vdd_gpu_mem_s0>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0m2_xfer>;
+ status = "okay";
+
+ vdd_cpu_big0_s0: regulator@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big0_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_4v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_big1_s0: regulator@43 {
+ compatible = "rockchip,rk8603", "rockchip,rk8602";
+ reg = <0x43>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big1_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_4v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ vdd_npu_s0: regulator@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_npu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_4v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c6 {
+ clock-frequency = <200000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6m0_xfer>;
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-output-names = "hym8563";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hym8563_int>;
+ wakeup-source;
+ };
+};
+
+&i2c7 {
+ clock-frequency = <200000>;
+ status = "okay";
+
+ rt5616: audio-codec@1b {
+ compatible = "realtek,rt5616";
+ reg = <0x1b>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&i2s0_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_lrck
+ &i2s0_mclk
+ &i2s0_sclk
+ &i2s0_sdi0
+ &i2s0_sdo0>;
+ status = "okay";
+};
+
+&i2s5_8ch {
+ status = "okay";
+};
+
+&i2s6_8ch {
+ status = "okay";
+};
+
+&i2s7_8ch {
+ status = "okay";
+};
+
+&pcie2x1l2 {
+ /* r8125 ethernet, @fe190000 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_2_rst>;
+ reset-gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_pcie20>;
+ status = "okay";
+};
+
+&pinctrl {
+ gpio-leds {
+ led_sys_pin: led-sys-pin {
+ rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ led_usr_pin: led-usr-pin {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ hym8563 {
+ hym8563_int: rtc-int {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pcie {
+ pcie2_2_rst: pcie2-2-rst {
+ rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sd_s0_pwr: sd-s0-pwr {
+ rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&avcc_1v8_s0>;
+ status = "okay";
+};
+
+/* eMMC */
+&sdhci {
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ no-sd;
+ no-sdio;
+ non-removable;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vcc_1v8_s3>;
+ status = "okay";
+};
+
+/* microSD card */
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <150000000>;
+ no-mmc;
+ no-sdio;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_sd_s0>;
+ vqmmc-supply = <&vccio_sd_s0>;
+};
+
+&spi2 {
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ status = "okay";
+
+ rk806_single: pmic@0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+
+ spi-max-frequency = <1000000>;
+ system-power-controller;
+
+ vcc1-supply = <&vcc_4v0_sys>;
+ vcc2-supply = <&vcc_4v0_sys>;
+ vcc3-supply = <&vcc_4v0_sys>;
+ vcc4-supply = <&vcc_4v0_sys>;
+ vcc5-supply = <&vcc_4v0_sys>;
+ vcc6-supply = <&vcc_4v0_sys>;
+ vcc7-supply = <&vcc_4v0_sys>;
+ vcc8-supply = <&vcc_4v0_sys>;
+ vcc9-supply = <&vcc_4v0_sys>;
+ vcc10-supply = <&vcc_4v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc_4v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc_4v0_sys>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ regulators {
+ vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_s0";
+ regulator-enable-ramp-delay = <400>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_cpu_lit_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_log_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_vdenc_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_ddr_s0: dcdc-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_ddr_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd2_ddr_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_2v0_pldo_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_3v3_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vddq_ddr_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg10 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "avcc_1v8_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s0: pldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avdd_1v2_s0: pldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "avdd_1v2_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_3v3_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vccio_sd_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ pldo6_s3: pldo-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "pldo6_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_ddr_pll_s0: nldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdd_ddr_pll_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "avdd_0v75_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdd_0v85_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v75_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&tsadc {
+ status = "okay";
+};
+
+/* Debug UART */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m0_xfer>;
+};
--
2.43.0
Powered by blists - more mailing lists