[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240627203856.66628-19-tony.luck@intel.com>
Date: Thu, 27 Jun 2024 13:38:56 -0700
From: Tony Luck <tony.luck@...el.com>
To: Fenghua Yu <fenghua.yu@...el.com>,
Reinette Chatre <reinette.chatre@...el.com>,
Maciej Wieczor-Retman <maciej.wieczor-retman@...el.com>,
Peter Newman <peternewman@...gle.com>,
James Morse <james.morse@....com>,
Babu Moger <babu.moger@....com>,
Drew Fustini <dfustini@...libre.com>,
Dave Martin <Dave.Martin@....com>
Cc: x86@...nel.org,
linux-kernel@...r.kernel.org,
patches@...ts.linux.dev,
Tony Luck <tony.luck@...el.com>
Subject: [PATCH v22 18/18] x86/resctrl: Update documentation with Sub-NUMA cluster changes
With Sub-NUMA Cluster (SNC) mode enabled the scope of monitoring resources
is per-NODE instead of per-L3 cache. Backwards compatibility is maintained
by providing files in the mon_L3_XX directories that sum event counts
for all SNC nodes sharing an L3 cache.
New files provide per-SNC node event counts.
Users should be aware that SNC mode also affects the amount of L3 cache
available for allocation within each SNC node.
Signed-off-by: Tony Luck <tony.luck@...el.com>
Reviewed-by: Reinette Chatre <reinette.chatre@...el.com>
---
Documentation/arch/x86/resctrl.rst | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/Documentation/arch/x86/resctrl.rst b/Documentation/arch/x86/resctrl.rst
index 627e23869bca..a824affd741d 100644
--- a/Documentation/arch/x86/resctrl.rst
+++ b/Documentation/arch/x86/resctrl.rst
@@ -375,6 +375,10 @@ When monitoring is enabled all MON groups will also contain:
all tasks in the group. In CTRL_MON groups these files provide
the sum for all tasks in the CTRL_MON group and all tasks in
MON groups. Please see example section for more details on usage.
+ On systems with Sub-NUMA Cluster (SNC) enabled there are extra
+ directories for each node (located within the "mon_L3_XX" directory
+ for the L3 cache they occupy). These are named "mon_sub_L3_YY"
+ where "YY" is the node number.
"mon_hw_id":
Available only with debug option. The identifier used by hardware
@@ -484,6 +488,29 @@ if non-contiguous 1s value is supported. On a system with a 20-bit mask
each bit represents 5% of the capacity of the cache. You could partition
the cache into four equal parts with masks: 0x1f, 0x3e0, 0x7c00, 0xf8000.
+Notes on Sub-NUMA Cluster mode
+==============================
+When SNC mode is enabled, Linux may load balance tasks between Sub-NUMA
+nodes much more readily than between regular NUMA nodes since the CPUs
+on Sub-NUMA nodes share the same L3 cache and the system may report
+the NUMA distance between Sub-NUMA nodes with a lower value than used
+for regular NUMA nodes.
+
+The top-level monitoring files in each "mon_L3_XX" directory provide
+the sum of data across all SNC nodes sharing an L3 cache instance.
+Users who bind tasks to the CPUs of a specific Sub-NUMA node can read
+the "llc_occupancy", "mbm_total_bytes", and "mbm_local_bytes" in the
+"mon_sub_L3_YY" directories to get node local data.
+
+Memory bandwidth allocation is still performed at the L3 cache
+level. I.e. throttling controls are applied to all SNC nodes.
+
+L3 cache allocation bitmaps also apply to all SNC nodes. But note that
+the amount of L3 cache represented by each bit is divided by the number
+of SNC nodes per L3 cache. E.g. with a 100MB cache on a system with 10-bit
+allocation masks each bit normally represents 10MB. With SNC mode enabled
+with two SNC nodes per L3 cache, each bit only represents 5MB.
+
Memory bandwidth Allocation and monitoring
==========================================
--
2.45.2
Powered by blists - more mailing lists