[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240628151518.40100-4-afd@ti.com>
Date: Fri, 28 Jun 2024 10:15:14 -0500
From: Andrew Davis <afd@...com>
To: Nishanth Menon <nm@...com>, Vignesh Raghavendra <vigneshr@...com>,
Tero
Kristo <kristo@...nel.org>, Rob Herring <robh+dt@...nel.org>,
Krzysztof
Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley
<conor+dt@...nel.org>,
Jan Kiszka <jan.kiszka@...mens.com>
CC: <linux-arm-kernel@...ts.infradead.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, Andrew Davis <afd@...com>
Subject: [PATCH 3/7] arm64: dts: ti: k3-j721e: Add cpsw-mac-efuse node to mcu_conf
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@...com>
---
arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 9349ae07c046e..6b6ef6a306142 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -34,13 +34,17 @@ k3_reset: reset-controller {
};
};
- mcu_conf: syscon@...00000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x0 0x40f00000 0x0 0x20000>;
+ mcu_conf: bus@...00000 {
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x0 0x40f00000 0x20000>;
+ cpsw_mac_syscon: ethernet-mac-syscon@200 {
+ compatible = "ti,am62p-cpsw-mac-efuse", "syscon";
+ reg = <0x200 0x8>;
+ };
+
phy_gmii_sel: phy@...0 {
compatible = "ti,am654-phy-gmii-sel";
reg = <0x4040 0x4>;
@@ -546,7 +550,7 @@ cpsw_port1: port@1 {
reg = <1>;
ti,mac-only;
label = "port1";
- ti,syscon-efuse = <&mcu_conf 0x200>;
+ ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
phys = <&phy_gmii_sel 1>;
};
};
--
2.39.2
Powered by blists - more mailing lists