[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20240702-cleanup-ad7606-v3-1-57fd02a4e2aa@baylibre.com>
Date: Tue, 02 Jul 2024 17:34:05 +0000
From: Guillaume Stols <gstols@...libre.com>
To: Lars-Peter Clausen <lars@...afoo.de>,
Michael Hennerich <Michael.Hennerich@...log.com>,
Jonathan Cameron <jic23@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: linux-iio@...r.kernel.org, linux-kernel@...r.kernel.org,
Michael Hennerich <michael.hennerich@...log.com>,
linux-fbdev@...r.kernel.org, devicetree@...r.kernel.org,
Jonathan Cameron <Jonathan.Cameron@...wei.com>,
Guillaume Stols <gstols@...libre.com>, jstephan@...libre.com,
dlechner@...libre.com
Subject: [PATCH v3 1/8] dt-bindings: iio: adc: adi,ad7606: normalize
textwidth
Normalize textwidth to 80 columns on the descriptions.
Acked-by: Rob Herring (Arm) <robh@...nel.org>
Signed-off-by: Guillaume Stols <gstols@...libre.com>
---
.../devicetree/bindings/iio/adc/adi,ad7606.yaml | 50 +++++++++++-----------
1 file changed, 24 insertions(+), 26 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index 00fdaed11cbd..32caa9fc00e4 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -40,60 +40,58 @@ properties:
adi,conversion-start-gpios:
description:
- Must be the device tree identifier of the CONVST pin.
- This logic input is used to initiate conversions on the analog
- input channels. As the line is active high, it should be marked
- GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the CONVST pin. This logic input is
+ used to initiate conversions on the analog input channels. As the line is
+ active high, it should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
reset-gpios:
description:
- Must be the device tree identifier of the RESET pin. If specified,
- it will be asserted during driver probe. As the line is active high,
- it should be marked GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the RESET pin. If specified, it will
+ be asserted during driver probe. As the line is active high, it should be
+ marked GPIO_ACTIVE_HIGH.
maxItems: 1
standby-gpios:
description:
- Must be the device tree identifier of the STBY pin. This pin is used
- to place the AD7606 into one of two power-down modes, Standby mode or
+ Must be the device tree identifier of the STBY pin. This pin is used to
+ place the AD7606 into one of two power-down modes, Standby mode or
Shutdown mode. As the line is active low, it should be marked
GPIO_ACTIVE_LOW.
maxItems: 1
adi,first-data-gpios:
description:
- Must be the device tree identifier of the FRSTDATA pin.
- The FRSTDATA output indicates when the first channel, V1, is
- being read back on either the parallel, byte or serial interface.
- As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA
+ output indicates when the first channel, V1, is being read back on either
+ the parallel, byte or serial interface. As the line is active high, it
+ should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
adi,range-gpios:
description:
- Must be the device tree identifier of the RANGE pin. The polarity on
- this pin determines the input range of the analog input channels. If
- this pin is tied to a logic high, the analog input range is ±10V for
- all channels. If this pin is tied to a logic low, the analog input range
- is ±5V for all channels. As the line is active high, it should be marked
+ Must be the device tree identifier of the RANGE pin. The polarity on this
+ pin determines the input range of the analog input channels. If this pin
+ is tied to a logic high, the analog input range is ±10V for all channels.
+ If this pin is tied to a logic low, the analog input range is ±5V for all
+ channels. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
maxItems: 1
adi,oversampling-ratio-gpios:
description:
- Must be the device tree identifier of the over-sampling
- mode pins. As the line is active high, it should be marked
- GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the over-sampling mode pins. As the
+ line is active high, it should be marked GPIO_ACTIVE_HIGH.
maxItems: 3
adi,sw-mode:
description:
Software mode of operation, so far available only for ad7616 and ad7606b.
- It is enabled when all three oversampling mode pins are connected to
- high level. The device is configured by the corresponding registers. If the
- adi,oversampling-ratio-gpios property is defined, then the driver will set the
- oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
- to VDD.
+ It is enabled when all three oversampling mode pins are connected to high
+ level. The device is configured by the corresponding registers. If the
+ adi,oversampling-ratio-gpios property is defined, then the driver will set
+ the oversampling gpios to high. Otherwise, it is assumed that the pins are
+ hardwired to VDD.
type: boolean
required:
--
2.34.1
Powered by blists - more mailing lists