| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <61649bee-f7dc-452c-beb5-cc8ee2179b99@beagleboard.org>
Date: Tue, 2 Jul 2024 20:44:26 +0530
From: Ayush Singh <ayush@...gleboard.org>
To: Rob Herring <robh@...nel.org>
Cc: Mark Brown <broonie@...nel.org>, Vaishnav M A <vaishnav@...gleboard.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley
<conor+dt@...nel.org>, Derek Kiernan <derek.kiernan@....com>,
Dragan Cvetic <dragan.cvetic@....com>, Arnd Bergmann <arnd@...db.de>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>, Nishanth Menon <nm@...com>,
Vignesh Raghavendra <vigneshr@...com>, Tero Kristo <kristo@...nel.org>,
Michael Walle <mwalle@...nel.org>, Andrew Lunn <andrew@...n.ch>,
jkridner@...gleboard.org, robertcnelson@...gleboard.org,
linux-spi@...r.kernel.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v5 1/7] dt-bindings: connector: Add mikrobus-connector
On 6/28/24 21:58, Rob Herring wrote:
> On Thu, Jun 27, 2024 at 09:56:11PM +0530, Ayush Singh wrote:
>> Add DT bindings for mikroBUS interface. MikroBUS is an open standard
>> developed by MikroElektronika for connecting add-on boards to
>> microcontrollers or microprocessors.
>>
>> mikroBUS is a connector and does not have a controller. Instead the
>> software is responsible for identification of board and setting up uart,
>> spi, i2c, pwm and other buses. Additionally, some new mikroBUS boards
>> contain 1-wire EEPROM that contains a manifest to describe the addon
>> board to provide plug and play capabilities.
>>
>> A mikroBUS addon board is free to leave some of the pins unused which
>> are marked as NC or Not Connected.
>>
>> Some of the pins might need to be configured as GPIOs deviating from their
>> reserved purposes Eg: SHT15 Click where the SCL and SDA Pins need to be
>> configured as GPIOs for the driver (drivers/hwmon/sht15.c) to work.
>>
>> For some add-on boards the driver may not take care of some additional
>> signals like reset/wake-up/other. Eg: ENC28J60 click where the reset line
>> (RST pin on the mikrobus port) needs to be pulled high.
>>
>> Some SPI addon boards use other pins like RST, AN etc as chipselect (eg.
>> SPI Extend Click). Thus, `spi-cs` and `spi-cs-names` property is added
>> to allow mikroBUS addon board to specify chipselect by name.
>>
>> Here's the list of pins in mikroBUS connector:
>> AN - Analog
>> RST - Reset
>> CS - SPI Chip Select
>> SCK - SPI Clock
>> MISO - SPI Master Input Slave Output
>> MOSI - SPI Master Output Slave Input
>> +3.3V - VCC-3.3V power
>> GND - Reference Ground
>> PWM - PWM output
>> INT - Hardware Interrupt
>> RX - UART Receive
>> TX - UART Transmit
>> SCL - I2C Clock
>> SDA - I2C Data
>> +5V - VCC-5V power
>> GND - Reference Ground
>>
>> Link: https://www.mikroe.com/mikrobus
>> Link:
>> https://download.mikroe.com/documents/standards/mikrobus/mikrobus-standard-specification-v200.pdf
>> mikroBUS specification
>> Link: https://www.mikroe.com/sht1x-click SHT15 Click
>> Link: https://www.mikroe.com/eth-click ENC28J60 Click
>> Link: https://www.mikroe.com/spi-extend-click SPI Extend Click
>>
>> Co-developed-by: Vaishnav M A <vaishnav@...gleboard.org>
>> Signed-off-by: Vaishnav M A <vaishnav@...gleboard.org>
>> Signed-off-by: Ayush Singh <ayush@...gleboard.org>
>> ---
>> .../bindings/connector/mikrobus-connector.yaml | 107 +++++++++++++++++++++
>> MAINTAINERS | 6 ++
>> 2 files changed, 113 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml b/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml
>> new file mode 100644
>> index 000000000000..033479f8604f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml
>> @@ -0,0 +1,107 @@
>> +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/connector/mikrobus-connector.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: mikroBUS add-on board connector
>> +
>> +maintainers:
>> + - Ayush Singh <ayush@...gleboard.org>
>> +
>> +properties:
>> + compatible:
>> + const: mikrobus-connector
>> +
>> + pinctrl-0: true
>> + pinctrl-1: true
>> + pinctrl-2: true
>> + pinctrl-3: true
>> + pinctrl-4: true
>> + pinctrl-5: true
>> + pinctrl-6: true
>> + pinctrl-7: true
>> + pinctrl-8: true
>> +
>> + pinctrl-names:
>> + minItems: 1
>> + maxItems: 9
>> + items:
>> + enum: [default, pwm_default, pwm_gpio, uart_default, uart_gpio, i2c_default, i2c_gpio, spi_default,
>> + spi_gpio]
> Generally, each pinctrl-N is mutually exclusive. It looks like here you
> want multiple states active at one time. Does this work?
I see. In mikrobus case, these pinctrl are not mutually exclusive. The
ones that are mutually exclusive are as follows:
- pwm_default and pwm_gpio
- uart_default and uart_gpio
- i2c_default and i2c_gpio
- spi_default and spi_gpio
It still does lead to 16 combinations so not sure if it is the best
approach.
>> +
>> + spi-controller:
>> + description: spi-controller of mikroBUS SPI pins along with cs pins.
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> +
>> + spi-cs:
>> + description: spi chip-select corresponding to the chip-selects on the mikrobus socket.
> Wrap lines at 80 char.
>
> The array index is the chip-select number on the connector and the
> value is the host SPI controller CS numbers? Or the other way around?
> This needs a better description.
>
>> + $ref: /schemas/types.yaml#/definitions/uint32-array
> Maximum number of entries?
>
>> +
>> + spi-cs-names:
>> + minItems: 1
>> + maxItems: 12
>> + items:
>> + enum: [default, pwm, int, rx, tx, scl, sda, an, rst, sck, cipo, copi]
>> +
>> + i2c-controller:
>> + description: i2c controller attached to the mikrobus socket.
>> + $ref: /schemas/types.yaml#/definitions/phandle
> i2c-bus is the somewhat standard property for this.
>
> Really, I'd expect connectors to look something like this:
>
> connector {
> i2c-0 {
> i2c-bus = <&i2c3>;
> #address-cells = <1>;
> #size-cells = <0>;
> device@12 {
> compatible = "some-i2c-device";
> };
> };
> };
>
> That form allows for multiple buses (of the same type or different) on
> the connector.
>
>> +
>> + uart-controller:
>> + description: uart controller attached to the mikrobus socket
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> +
>> + pwms:
>> + description: the pwm-controller corresponding to the mikroBUS PWM pin.
>> + maxItems: 1
>> +
>> + mikrobus-gpios:
>> + minItems: 1
>> + maxItems: 12
>> +
>> + mikrobus-gpio-names:
> The GPIO binding does not work this way as the name is in the property.
> Either drop if you want to keep the array or you have to do something
> like this:
>
> pwm-gpios
> int-gpios
> rx-gpios
>
> Really, the intention was for connectors to use gpio-map property to
> renumber GPIOs relative to the connector.
Can you point me to what you mean by gpio-map property?
>> + minItems: 1
>> + maxItems: 12
>> + items:
>> + enum: [pwm, int, rx, tx, scl, sda, an, rst, cs, sck, cipo, copi]
>> +
>> + board:
>> + description: board attached to mikrobus connector
>> + $ref: /schemas/types.yaml#/definitions/phandle-array
> What is this for?
>
>> +
>> +required:
>> + - compatible
>> + - pinctrl-0
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/gpio/gpio.h>
>> + mikrobus {
>> + compatible = "mikrobus-connector";
>> + pinctrl-names = "default", "pwm_default", "pwm_gpio","uart_default", "uart_gpio", "i2c_default",
>> + "i2c_gpio", "spi_default", "spi_gpio";
>> + pinctrl-0 = <&P2_03_gpio_input_pin &P1_04_gpio_pin &P1_02_gpio_pin>;
>> + pinctrl-1 = <&P2_01_pwm_pin>;
>> + pinctrl-2 = <&P2_01_gpio_pin>;
>> + pinctrl-3 = <&P2_05_uart_pin &P2_07_uart_pin>;
>> + pinctrl-4 = <&P2_05_gpio_pin &P2_07_gpio_pin>;
>> + pinctrl-5 = <&P2_09_i2c_pin &P2_11_i2c_pin>;
>> + pinctrl-6 = <&P2_09_gpio_pin &P2_11_gpio_pin>;
>> + pinctrl-7 = <&P1_12_spi_pin &P1_10_spi_pin &P1_08_spi_sclk_pin &P1_06_spi_cs_pin>;
>> + pinctrl-8 = <&P1_12_gpio_pin &P1_10_gpio_pin &P1_08_gpio_pin &P1_06_gpio_pin>;
>> + pwms = <&ehrpwm1 0 500000 0>;
>> + i2c-controller = <&i2c1>;
>> + uart-controller = <&uart1>;
>> + spi-controller = <&spi1>;
>> + spi-cs = <0 1>;
>> + spi-cs-names = "default", "rst";
>> + mikrobus-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>, <&gpio0 23 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 30 GPIO_ACTIVE_HIGH>, <&gpio0 31 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 15 GPIO_ACTIVE_HIGH>, <&gpio0 14 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 4 GPIO_ACTIVE_HIGH>, <&gpio0 3 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 2 GPIO_ACTIVE_HIGH>, <&gpio0 5 GPIO_ACTIVE_HIGH>,
>> + <&gpio2 25 GPIO_ACTIVE_HIGH>, <&gpio2 3 GPIO_ACTIVE_HIGH>;
>> + };
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 807feae089c4..8e4115e93aeb 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -15108,6 +15108,12 @@ M: Oliver Neukum <oliver@...kum.org>
>> S: Maintained
>> F: drivers/usb/image/microtek.*
>>
>> +MIKROBUS
>> +M: Ayush Singh <ayush@...gleboard.org>
>> +M: Vaishnav M A <vaishnav@...gleboard.org>
>> +S: Maintained
>> +F: Documentation/devicetree/bindings/connector/mikrobus-connector.yaml
>> +
>> MIKROTIK CRS3XX 98DX3236 BOARD SUPPORT
>> M: Luka Kovacic <luka.kovacic@...tura.hr>
>> M: Luka Perkov <luka.perkov@...tura.hr>
>>
>> --
>> 2.45.2
>>
I am switching to child-node based structure from the next patch since I
was able to replicate applying board overlay on a generic connector with
child node.
Ayush Singh
Powered by blists - more mailing lists