| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20240708140542.2424824-1-o.rempel@pengutronix.de>
Date: Mon, 8 Jul 2024 16:05:42 +0200
From: Oleksij Rempel <o.rempel@...gutronix.de>
To: Andrew Lunn <andrew@...n.ch>,
Heiner Kallweit <hkallweit1@...il.com>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>
Cc: Oleksij Rempel <o.rempel@...gutronix.de>,
kernel@...gutronix.de,
linux-kernel@...r.kernel.org,
netdev@...r.kernel.org
Subject: [PATCH net-next v1 1/1] net: phy: dp83td510: add cable testing support
Implement the TDR test procedure as described in "Application Note
DP83TD510E Cable Diagnostics Toolkit revC", section 3.2.
The procedure was tested with "draka 08 signalkabel 2x0.8mm". The reported
cable length was 5 meters more for each 20 meters of actual cable length.
For instance, a 20-meter cable showed as 25 meters, and a 40-meter cable
showed as 50 meters. Since other parts of the diagnostics provided by this
PHY (e.g., Active Link Cable Diagnostics) require accurate cable
characterization to provide proper results, this tuning can be implemented
in a separate patch/interface.
Signed-off-by: Oleksij Rempel <o.rempel@...gutronix.de>
---
drivers/net/phy/dp83td510.c | 158 ++++++++++++++++++++++++++++++++++++
1 file changed, 158 insertions(+)
diff --git a/drivers/net/phy/dp83td510.c b/drivers/net/phy/dp83td510.c
index d7616b13c5946..3375fa82927d0 100644
--- a/drivers/net/phy/dp83td510.c
+++ b/drivers/net/phy/dp83td510.c
@@ -4,6 +4,7 @@
*/
#include <linux/bitfield.h>
+#include <linux/ethtool_netlink.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
@@ -29,6 +30,42 @@
#define DP83TD510E_INT1_LINK BIT(13)
#define DP83TD510E_INT1_LINK_EN BIT(5)
+#define DP83TD510E_TDR_CFG 0x1e
+#define DP83TD510E_TDR_START BIT(15)
+#define DP83TD510E_TDR_DONE BIT(1)
+#define DP83TD510E_TDR_FAIL BIT(0)
+
+#define DP83TD510E_CTRL 0x1f
+#define DP83TD510E_CTRL_HW_RESET BIT(15)
+#define DP83TD510E_CTRL_SW_RESET BIT(14)
+
+#define DP83TD510E_TDR_CFG1 0x300
+/* TX_TYPE: Transmit voltage level for TDR. 0 = 1V, 1 = 2.4V */
+#define DP83TD510E_TDR_TX_TYPE BIT(12)
+
+#define DP83TD510E_TDR_CFG2 0x301
+#define DP83TD510E_TDR_END_TAP_INDEX_1 GENMASK(14, 8)
+#define DP83TD510E_TDR_END_TAP_INDEX_1_DEF 36
+#define DP83TD510E_TDR_START_TAP_INDEX_1 GENMASK(6, 0)
+#define DP83TD510E_TDR_START_TAP_INDEX_1_DEF 3
+
+#define DP83TD510E_TDR_FAULT_CFG1 0x303
+#define DP83TD510E_TDR_FLT_LOC_OFFSET_1 GENMASK(14, 8)
+#define DP83TD510E_TDR_FLT_LOC_OFFSET_1_DEF 4
+#define DP83TD510E_TDR_FLT_INIT_1 GENMASK(7, 0)
+#define DP83TD510E_TDR_FLT_INIT_1_DEF 62
+
+#define DP83TD510E_TDR_FAULT_STAT 0x30c
+#define DP83TD510E_TDR_PEAK_DETECT BIT(11)
+#define DP83TD510E_TDR_PEAK_SIGN BIT(10)
+#define DP83TD510E_TDR_PEAK_LOCATION GENMASK(9, 0)
+
+/* Not documented registers and values but recommended according to
+ * "DP83TD510E Cable Diagnostics Toolkit revC"
+ */
+#define DP83TD510E_UNKN_030E 0x30e
+#define DP83TD510E_030E_VAL 0x2520
+
#define DP83TD510E_AN_STAT_1 0x60c
#define DP83TD510E_MASTER_SLAVE_RESOL_FAIL BIT(15)
@@ -198,6 +235,124 @@ static int dp83td510_get_sqi_max(struct phy_device *phydev)
return DP83TD510_SQI_MAX;
}
+/**
+ * dp83td510_cable_test_start - Start the cable test for the DP83TD510 PHY.
+ * @phydev: Pointer to the phy_device structure.
+ *
+ * This sequence is implemented according to the "Application Note DP83TD510E
+ * Cable Diagnostics Toolkit revC".
+ *
+ * Return: 0 on success, a negative error code on failure.
+ */
+static int dp83td510_cable_test_start(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_CTRL,
+ DP83TD510E_CTRL_HW_RESET);
+ if (ret)
+ return ret;
+
+ ret = genphy_c45_an_disable_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* Force master mode */
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_PMD_BT1_CTRL,
+ MDIO_PMA_PMD_BT1_CTRL_CFG_MST);
+ if (ret)
+ return ret;
+
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_TDR_CFG2,
+ FIELD_PREP(DP83TD510E_TDR_END_TAP_INDEX_1,
+ DP83TD510E_TDR_END_TAP_INDEX_1_DEF) |
+ FIELD_PREP(DP83TD510E_TDR_START_TAP_INDEX_1,
+ DP83TD510E_TDR_START_TAP_INDEX_1_DEF));
+ if (ret)
+ return ret;
+
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_TDR_FAULT_CFG1,
+ FIELD_PREP(DP83TD510E_TDR_FLT_LOC_OFFSET_1,
+ DP83TD510E_TDR_FLT_LOC_OFFSET_1_DEF) |
+ FIELD_PREP(DP83TD510E_TDR_FLT_INIT_1,
+ DP83TD510E_TDR_FLT_INIT_1_DEF));
+ if (ret)
+ return ret;
+
+ /* Undocumented register, from the "Application Note DP83TD510E Cable
+ * Diagnostics Toolkit revC".
+ */
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_UNKN_030E,
+ DP83TD510E_030E_VAL);
+ if (ret)
+ return ret;
+
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_CTRL,
+ DP83TD510E_CTRL_SW_RESET);
+ if (ret)
+ return ret;
+
+ return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_TDR_CFG,
+ DP83TD510E_TDR_START);
+}
+
+/**
+ * dp83td510_cable_test_get_status - Get the status of the cable test for the
+ * DP83TD510 PHY.
+ * @phydev: Pointer to the phy_device structure.
+ * @finished: Pointer to a boolean that indicates whether the test is finished.
+ *
+ * The function sets the @finished flag to true if the test is complete, and
+ * returns 0 on success or a negative error code on failure.
+ */
+static int dp83td510_cable_test_get_status(struct phy_device *phydev,
+ bool *finished)
+{
+ int ret, stat;
+
+ *finished = false;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_TDR_CFG);
+ if (ret < 0)
+ return ret;
+
+ if (!(ret & DP83TD510E_TDR_DONE))
+ return 0;
+
+ if (!(ret & DP83TD510E_TDR_FAIL)) {
+ int location;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ DP83TD510E_TDR_FAULT_STAT);
+ if (ret < 0)
+ return ret;
+
+ if (ret & DP83TD510E_TDR_PEAK_DETECT) {
+ if (ret & DP83TD510E_TDR_PEAK_SIGN)
+ stat = ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+ else
+ stat = ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+
+ location = FIELD_GET(DP83TD510E_TDR_PEAK_LOCATION,
+ ret) * 100;
+ ethnl_cable_test_fault_length(phydev,
+ ETHTOOL_A_CABLE_PAIR_A,
+ location);
+ } else {
+ stat = ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ }
+ } else {
+ /* Most probably we have active link partner */
+ stat = ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+ }
+
+ *finished = true;
+
+ ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A, stat);
+
+ return phy_init_hw(phydev);
+}
+
static int dp83td510_get_features(struct phy_device *phydev)
{
/* This PHY can't respond on MDIO bus if no RMII clock is enabled.
@@ -221,6 +376,7 @@ static struct phy_driver dp83td510_driver[] = {
PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID),
.name = "TI DP83TD510E",
+ .flags = PHY_POLL_CABLE_TEST,
.config_aneg = dp83td510_config_aneg,
.read_status = dp83td510_read_status,
.get_features = dp83td510_get_features,
@@ -228,6 +384,8 @@ static struct phy_driver dp83td510_driver[] = {
.handle_interrupt = dp83td510_handle_interrupt,
.get_sqi = dp83td510_get_sqi,
.get_sqi_max = dp83td510_get_sqi_max,
+ .cable_test_start = dp83td510_cable_test_start,
+ .cable_test_get_status = dp83td510_cable_test_get_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
--
2.39.2
Powered by blists - more mailing lists