| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240711132001.2792-1-baojun.xu@ti.com>
Date: Thu, 11 Jul 2024 21:20:01 +0800
From: Baojun Xu <baojun.xu@...com>
To: <tiwai@...e.de>
CC: <robh+dt@...nel.org>, <andriy.shevchenko@...ux.intel.com>,
<lgirdwood@...il.com>, <perex@...ex.cz>,
<pierre-louis.bossart@...ux.intel.com>, <kevin-lu@...com>,
<shenghao-ding@...com>, <navada@...com>, <13916275206@....com>,
<v-hampiholi@...com>, <v-po@...com>, <niranjan.hy@...com>,
<alsa-devel@...a-project.org>, <linux-kernel@...r.kernel.org>,
<liam.r.girdwood@...el.com>, <yung-chuan.liao@...ux.intel.com>,
<baojun.xu@...com>, <broonie@...nel.org>, <soyer@....hu>
Subject: [PATCH v9] ALSA: hda/tas2781: Add tas2781 hda SPI driver
This patch was used to add TAS2781 devices on SPI support in sound/pci/hda.
It use ACPI node descript about parameters of TAS2781 on SPI, it like:
Scope (_SB.PC00.SPI0)
{
Device (GSPK)
{
Name (_HID, "TXNW2781") // _HID: Hardware ID
Method (_CRS, 0, NotSerialized)
{
Name (RBUF, ResourceTemplate ()
{
SpiSerialBusV2 (...)
SpiSerialBusV2 (...)
}
}
}
}
And in platform/x86/serial-multi-instantiate.c, those spi devices will be
added into system as a single SPI device, so TAS2781 SPI driver will
probe twice for every single SPI device. And driver will also parser
mono DSP firmware binary and RCA binary for itself.
The code support Realtek as the primary codec.
Signed-off-by: Baojun Xu <baojun.xu@...com>
---
v9:
- Add parentheses for variables in micro define.
- Add define for calibration registers address identify.
- Change variable name from calibration_data to cali_data.
- Add variable for calibration registers address in struct tasdevice_priv.
- Change format for alignment to parentheses.
- Remove tas2781_reg_defaults as it will be over write in firmware download.
- Remove RESET for second device in tas2781_spi_reset(),
as it will cause no sound on second device.
- Add calibration registers address initial in tasdevice_spi_init().
- Remove unnecessary parentheses.
- Remove exception in tas2781_hda_playback_hook().
- Remove hard code for calibration registers address.
- Add support for calibration data format V3 for registers address identify,
as new firmware tool will define calibration registers address dynamic,
so can't hard code it, need read it from BIOS with calibration data.
- Remove some debug print.
- Change hard code value (3) to ARRAY_SIZE(tas2781_snd_controls)/2.
- New patch apply for change position of component_del().
- Change label from out, out1 to config_err and block_err.
- Remove unnecessary parentheses in tas2781_spi_fwlib.c.
- Remove tasdevice_spi_prmg_calibdata_load().
v8:
- Move *-y position in sound/pci/hda/Makefile.
- Change + to | for bit operation in macro define.
- Change TASDEVICE_Checksum to TASDEVICE_CHECKSUM.
v7:
- Add new project Gemtree (0x103c8daa) support for tas2781 spi driver.
v6:
- Remove client in tasdevice_priv struct as it was not used.
- Change format for tasdevice_spi_dev_write() in tas2781_hda_spi.c.
- Change update bits function to read & write mode, as tas2781 use last bit
to mask read & write, it cause regmap_update_bits work not as our expected.
- Add element in tas2781_snd_controls, tas2781_prof_ctrl,
tas2781_dsp_conf_ctrl, to support second device.
Previous version add sound card for first index only.
- Change calibration registers address declaire to TASDEVICE_REG() mode.
- Add snd_ctl_new1() for second device.
- Change format for tas2781_hda_unbind() to fit 79 chars in one line.
- Remove client for spi as it was not used.
- Remove unused variables.
- Remove cur_prog clean in runtime_suspend().
- Remove unused variables.
- Add tasdevice_spi_tuning_switch() in runtime_resume.
- Remove cur_prog clean in system_resume().
- Add tuning switch if playback started in system_resume().
- Change TASDEVICE_PAGE_REG to TASDEVICE_REG_ID in tas2781_spi_fwlib.c.
- Remove calibration binary load functions as data will be loaded from EFI.
v5:
- Combined all modification into one patch for pass the compile.
- Remove old hardware id "TIAS2781" as no production on market.
- Change max page size to 256 in tas2781-spi.h.
- Change book reg from 127 to GENMASK(7, 1), as one bit shift is needed.
- Change register address define as one bit shift needed for offset.
- Change block check sum comments to Firmware block from I2C.
- Change define of (page + reg) to TASDEVICE_PAGE_REG from TASDEVICE_PGRG.
- Change to lower case in defined value.
- Add registers default value table in tas2781_hda_spi.c
- Change rang_max to 256 * 256.
- Add zero_flag_mask in regmap_config.
- Change max_register to 256 * 256.
- Add registers default table into structure regmap_config.
- Change parameter from book number to whole register address.
- Remove page 0 switch as SPI driver will do it.
- Add bit(0) for read function as tas2781 will check last bit of address,
to determine operation mode is read (1) or write (0).
- Change switch case to if check in tas2781_hda_playback_hook(),
as it may cause compile problem in clang-19 building.
- Change variable declaration position.
- Change order in if check.
- Remove old hardware id ("TIAS2781") support.
- Remove debug message in runtime suspend and resume.
- Remove regmap.h include in tas2781_spi_fwlib.c.
- Remove MODULE_ in fwlib as this file will work with tas2781_hda_spi.c only.
v4:
- Add old hardware id "TIAS2781" for compatible with old production
- Add 2 devices in struct smi_node tas2781_hda, to compatible with 4 AMPs
v4:
- Add old hardware id "TIAS2781" for compatible with old production
- Add 2 devices in struct smi_node tas2781_hda, to compatible with 4 AMPs
- Move include of sound/tas2781-dsp.h to c source file tas2781_hda_spi.c,
tas2781_spi_fwlib.c, as it's not needed in header file tas2781-spi.h
- Use page and book number define in other micro define
- Change 4000000 to (4 * HZ_PER_MHZ)
- Add define for calibration variable name and size in UEFI.
- Remove structure tasdevice & tasdevice_irqinfo, and move variables in to
structure tasdevice_priv
- Remove some unused variables in sttructure tasdevice_priv
- Remove function declare of tascodec_init(), use tascodec_spi_init()
- Remove function declare of tasdevice_remove()
- Add array_size.h included in tas2781_hda_spi.c
- Add cleanup.h included for change mutex to guard
- Add units.h included
- Include tas2781-dsp.h
- Remove unused variables in tas2781_hda structure
- Change 0xff to GENMASK(7, 0)
- Change 128 to define of max page size
- Change code as all variables was moved to tasdevice_priv structure
- Change comments for error in book write, or page write
- Remove initial of ret, and return 0 directly
- Change comments for wrong typo, add space in front and end
- Add check for bulk read, max size should be a page size
- Change usleep_rang() to fsleep()
- Change mutex_lock to guard(mutex), and remove mutex_unlock()
- Change tasdevice_spi_init() to void from int as no value return required
- Change second parameter to sizeof
- Remove tasdevice_clamp(), use clamp()
- Add compatible with old hardware id "TIAS2781"
- Remove cs_gpio and spi device in tas2781_read_acpi() as use default CS
- Change dev-index check, return -EINVAL if it's <= 0
- Change 0xFF to U8_MAX
- Remove GPIO get for chip-select, use default from SPI device
- Perform RESET in first AMP only as all AMPs share same RESET pin
- return 0 directly in some simple routine to avoid variable initial
- Change comments for function which was used by system
- Change "ON" "OFF" to function str_on_off(...)
- Change format of GUID
- Add temp buffer for first efi.get_variable()
- Free data if it was allocated
- Change format of debug message of calibration date time print
- Remove total_sz = 0, as it's not needed
- Move save_calibration to after tuning_switch to avoid calibration data
overwrite
- Remove dev from structure tasdevice_hda, use dev in tasdevice_priv
- Remove 0 from { "tas2781-hda", 0}, & {"TXNW2781", 0},
- Add old hardware id "TIAS2781" for compatible with old production
- Add 2 devices in struct smi_node tas2781_hda, to compatible with 4 AMPs
v3:
- Move HID up to above /* Non-conforming _HID ... */ in scan.c,
for avoid misunderstanding.
- Move HID up to above /* Non-conforming _HID ... */ in
serial-multi-instantiate.c, for avoid misunderstanding.
- Change objs to y for snd-hda-scodec-tas2781-spi- in Makefile.
- Change format for some define in tas2781-spi.h.
- Add define for TASDEVICE_MAX_BOOK_NUM, TASDEVICE_MAX_PAGE.
- Move declare of "enum calib_data {" to header file from source file.
- Remove "enum device_catlog_id {" as only one platform was supported now.
- Remove "struct calidata", as we will save pure calibration data only.
- Remove "struct calidata", "enum device_catlog_id" in tasdevice_priv.
- Add calibration_data in tasdevice_priv to save pure calibration data.
- Remove declare of tasdevice_save_calibration() and
tasdevice_apply_calibration(), as it will be used within same c file.
- Add below header files included in tas2781_hda_spi.c:
bits.h, mutex.h, property.h, time.h, types.h.
- Move two micro define to header file tas2781-spi.h.
- Change format of some micro define.
- Change format of some structure.
- Remove irq in tas2781_hda, as have it already in tasdevice_priv.
- Remove some local functions declare as not necessarily.
- Return error if regmap_write() failed.
- Change fixed value 2 to sizeof(data).
- Remove all of EXPORT_SYMBOL_GPL,
as all of function was called within same module.
- Remove empty line after last return in some functions.
- Remove some variable initialyzation.
- Remove variable sub, store acpi_subsystem_id directly.
- Remove wrong comments for device index, it's must, can't be NULL.
- Remove some local variables, use elements in structure directly.
- Append commas in last element of an array.
- Change calibration data process, didn't save all of calibration data in EFI,
get in local, and save pure calibration data in tasdevice_priv.
- Call tasdevice_save_calibration() from function pointer in tasdevice_priv;
- Remove subid as one platform was supported only, needn't check.
- Add initialyzation for local variable.
- Move regmap initialyzation to before acpi read.
- Call tasdevice_apply_calibration() from function pointer in tasdevice_priv;
- Remove MODULE_IMPORT_NS(SND_SOC_TAS2781_FMWLIB), as all functions was
performed within same module.
- Update format and variables declare order.
- Change format of multi conditions for if.
- Remove casting which is not needed.
- Change variables type to avoid casting.
- Remove Unneeded parentheses.
- Change if check to avoid goto.
- Add {} for keep same style.
- Remove some local variables, use elements in structure directly.
v2:
- Change depends on SPI to SPI_MASTER in sound/pci/hda/Kconfig
- Add select SND_HDA_SCODEC_COMPONENT in sound/pci/hda/Kconfig
- Change comp_generic_fixup() 5th parameter from "-%s:00" to
"-%s:00-tas2781-hda.%d" in sound/pci/hda/patch_realtek.c
- Change chain_id from ALC285_FIXUP_THINKPAD_HEADSET_JACK to
ALC285_FIXUP_HP_GPIO_LED in sound/pci/hda/patch_realtek.c
- Remove project name "Gemtree"
- Update information in file header of tas2781-spi.h.
- Remove useless micro define.
- Change TASDEVICE_I2CChecksum to TASDEVICE_Checksum
- Remove enum control_bus as current code support SPI only.
- Remove device define as current code support TAS2781 only.
- Remove spi_device **spi_devs in structure tasdevice_priv.
- Remove cal_binaryname in structure tasdevice_priv.
- Remove ndev in structure tasdevice_priv.
- Change isacpi and isspi, replace by control_bus(I2C or SPI).
- Remove void tasdevice_spi_dsp_remove(void *context).
- Add acpi_device and irq in structure tas2781_hda in tas2781_hda_spi.c.
- Remove parameter chn in all of registers access functions.
- Add tascodec_spi_init().
- Add chip select gpio set for SPI device.
- Change tasdevice_tuning_switch() to tasdevice_spi_tuning_switch().
- Change device offset from tas_priv->ndev to tas_priv->index.
- Change tasdevice_dsp_remove() to tasdevice_spi_dsp_remove().
- tasdevice_prmg_load() to tasdevice_spi_prmg_load().
- Change tasdevice_config_info_remove() to
tasdevice_spi_config_info_remove().
- Add one dummy byte shift when read from page 2~127, or not book 0.
- Change tasdevice_spi_change_chn_book() to tasdevice_spi_switch_book()
- Perform put_device(physdev) before error return.
- Change calibration data id to 2781 from 2783 in EFI
- Change calibration data structure name in comments.
- Remove file name in tas2781_spi_fwlib.c.
- Remove #include <linux/i2c.h> as it not needed in SPI mode.
- Change TAB to speace in micro define in tas2781_spi_fwlib.c.
- Change to up-case for DSP.
- Change all of multi-line comments format, empty first line.
- Change all of sizeof(struct xx) to sizeof(*xx).
- Remove Explicit casting for variables compare to avoid possible fault.
- Return directly without goto.
- Change 1 << xx to BIT(xx).
- Remove deviceNumber[] as current SPI device will support one device only.
- Add memory free before return error.
- Change "buf[offset]; offset += 1" to buf[offset++].
- Remove some debug information print.
- Change firmware binary to single device mode.
- Change all bexx_to_cpup() to get_unaligned_bexx().
- Remove ndev process as current SPI device support single device only.
- Remove chn and chnend for single device support only.
- Change all of registers read/write function, remove parameter chn.
- Create new function for single write, burst write, delay, field write
in tasdevice_process_block().
---
drivers/acpi/scan.c | 1 +
.../platform/x86/serial-multi-instantiate.c | 12 +
sound/pci/hda/Kconfig | 14 +
sound/pci/hda/Makefile | 2 +
sound/pci/hda/patch_realtek.c | 14 +
sound/pci/hda/tas2781-spi.h | 154 ++
sound/pci/hda/tas2781_hda_spi.c | 1266 ++++++++++
sound/pci/hda/tas2781_spi_fwlib.c | 2112 +++++++++++++++++
8 files changed, 3575 insertions(+)
create mode 100644 sound/pci/hda/tas2781-spi.h
create mode 100644 sound/pci/hda/tas2781_hda_spi.c
create mode 100644 sound/pci/hda/tas2781_spi_fwlib.c
diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c
index 503773707e01..9c08c5886370 100644
--- a/drivers/acpi/scan.c
+++ b/drivers/acpi/scan.c
@@ -1760,6 +1760,7 @@ static bool acpi_device_enumeration_by_parent(struct acpi_device *device)
{"CSC3557", },
{"INT33FE", },
{"INT3515", },
+ {"TXNW2781", },
/* Non-conforming _HID for Cirrus Logic already released */
{"CLSA0100", },
{"CLSA0101", },
diff --git a/drivers/platform/x86/serial-multi-instantiate.c b/drivers/platform/x86/serial-multi-instantiate.c
index 97b9c6392230..23d46063423d 100644
--- a/drivers/platform/x86/serial-multi-instantiate.c
+++ b/drivers/platform/x86/serial-multi-instantiate.c
@@ -368,6 +368,17 @@ static const struct smi_node cs35l57_hda = {
.bus_type = SMI_AUTO_DETECT,
};
+static const struct smi_node tas2781_hda = {
+ .instances = {
+ { "tas2781-hda", IRQ_RESOURCE_AUTO, 0 },
+ { "tas2781-hda", IRQ_RESOURCE_AUTO, 0 },
+ { "tas2781-hda", IRQ_RESOURCE_AUTO, 0 },
+ { "tas2781-hda", IRQ_RESOURCE_AUTO, 0 },
+ {}
+ },
+ .bus_type = SMI_AUTO_DETECT,
+};
+
/*
* Note new device-ids must also be added to ignore_serial_bus_ids in
* drivers/acpi/scan.c: acpi_device_enumeration_by_parent().
@@ -380,6 +391,7 @@ static const struct acpi_device_id smi_acpi_ids[] = {
{ "CSC3556", (unsigned long)&cs35l56_hda },
{ "CSC3557", (unsigned long)&cs35l57_hda },
{ "INT3515", (unsigned long)&int3515_data },
+ { "TXNW2781", (unsigned long)&tas2781_hda },
/* Non-conforming _HID for Cirrus Logic already released */
{ "CLSA0100", (unsigned long)&cs35l41_hda },
{ "CLSA0101", (unsigned long)&cs35l41_hda },
diff --git a/sound/pci/hda/Kconfig b/sound/pci/hda/Kconfig
index a3cf0725fc43..976fa370be24 100644
--- a/sound/pci/hda/Kconfig
+++ b/sound/pci/hda/Kconfig
@@ -206,6 +206,20 @@ config SND_HDA_SCODEC_TAS2781_I2C
comment "Set to Y if you want auto-loading the side codec driver"
depends on SND_HDA=y && SND_HDA_SCODEC_TAS2781_I2C=m
+config SND_HDA_SCODEC_TAS2781_SPI
+ tristate "Build TAS2781 HD-audio side codec support for SPI Bus"
+ depends on SPI_MASTER
+ depends on ACPI
+ depends on EFI
+ depends on SND_SOC
+ select CRC32_SARWATE
+ help
+ Say Y or M here to include TAS2781 SPI HD-audio side codec support
+ in snd-hda-intel driver, such as ALC287.
+
+comment "Set to Y if you want auto-loading the side codec driver"
+ depends on SND_HDA=y && SND_HDA_SCODEC_TAS2781_SPI=m
+
config SND_HDA_CODEC_REALTEK
tristate "Build Realtek HD-audio codec support"
select SND_HDA_GENERIC
diff --git a/sound/pci/hda/Makefile b/sound/pci/hda/Makefile
index 058ca0a289e4..39bb30803b24 100644
--- a/sound/pci/hda/Makefile
+++ b/sound/pci/hda/Makefile
@@ -39,6 +39,7 @@ snd-hda-scodec-cs35l56-spi-y := cs35l56_hda_spi.o
snd-hda-cs-dsp-ctls-y := hda_cs_dsp_ctl.o
snd-hda-scodec-component-y := hda_component.o
snd-hda-scodec-tas2781-i2c-y := tas2781_hda_i2c.o
+snd-hda-scodec-tas2781-spi-y := tas2781_hda_spi.o tas2781_spi_fwlib.o
# common driver
obj-$(CONFIG_SND_HDA) := snd-hda-codec.o
@@ -70,6 +71,7 @@ obj-$(CONFIG_SND_HDA_SCODEC_CS35L56_SPI) += snd-hda-scodec-cs35l56-spi.o
obj-$(CONFIG_SND_HDA_CS_DSP_CONTROLS) += snd-hda-cs-dsp-ctls.o
obj-$(CONFIG_SND_HDA_SCODEC_COMPONENT) += snd-hda-scodec-component.o
obj-$(CONFIG_SND_HDA_SCODEC_TAS2781_I2C) += snd-hda-scodec-tas2781-i2c.o
+obj-$(CONFIG_SND_HDA_SCODEC_TAS2781_SPI) += snd-hda-scodec-tas2781-spi.o
# this must be the last entry after codec drivers;
# otherwise the codec patches won't be hooked before the PCI probe
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 811e82474200..3abed3b0ed40 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6925,6 +6925,11 @@ static void tas2781_fixup_i2c(struct hda_codec *cdc,
comp_generic_fixup(cdc, action, "i2c", "TIAS2781", "-%s:00", 1);
}
+static void tas2781_fixup_spi(struct hda_codec *cdc, const struct hda_fixup *fix, int action)
+{
+ comp_generic_fixup(cdc, action, "spi", "TXNW2781", "-%s:00-tas2781-hda.%d", 2);
+}
+
static void yoga7_14arb7_fixup_i2c(struct hda_codec *cdc,
const struct hda_fixup *fix, int action)
{
@@ -7502,6 +7507,7 @@ enum {
ALC236_FIXUP_DELL_DUAL_CODECS,
ALC287_FIXUP_CS35L41_I2C_2_THINKPAD_ACPI,
ALC287_FIXUP_TAS2781_I2C,
+ ALC245_FIXUP_TAS2781_SPI_2,
ALC287_FIXUP_YOGA7_14ARB7_I2C,
ALC245_FIXUP_HP_MUTE_LED_COEFBIT,
ALC245_FIXUP_HP_X360_MUTE_LEDS,
@@ -9727,6 +9733,12 @@ static const struct hda_fixup alc269_fixups[] = {
.chained = true,
.chain_id = ALC285_FIXUP_THINKPAD_HEADSET_JACK,
},
+ [ALC245_FIXUP_TAS2781_SPI_2] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = tas2781_fixup_spi,
+ .chained = true,
+ .chain_id = ALC285_FIXUP_HP_GPIO_LED,
+ },
[ALC287_FIXUP_YOGA7_14ARB7_I2C] = {
.type = HDA_FIXUP_FUNC,
.v.func = yoga7_14arb7_fixup_i2c,
@@ -10200,6 +10212,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = {
SND_PCI_QUIRK(0x103c, 0x8b8d, "HP", ALC236_FIXUP_HP_GPIO_LED),
SND_PCI_QUIRK(0x103c, 0x8b8f, "HP", ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED),
SND_PCI_QUIRK(0x103c, 0x8b92, "HP", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+ SND_PCI_QUIRK(0x103c, 0x8b93, "HP Varcolac", ALC245_FIXUP_TAS2781_SPI_2),
SND_PCI_QUIRK(0x103c, 0x8b96, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
SND_PCI_QUIRK(0x103c, 0x8b97, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
SND_PCI_QUIRK(0x103c, 0x8bb3, "HP Slim OMEN", ALC287_FIXUP_CS35L41_I2C_2),
@@ -10263,6 +10276,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = {
SND_PCI_QUIRK(0x103c, 0x8cdf, "HP SnowWhite", ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED),
SND_PCI_QUIRK(0x103c, 0x8ce0, "HP SnowWhite", ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED),
SND_PCI_QUIRK(0x103c, 0x8cf5, "HP ZBook Studio 16", ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED),
+ SND_PCI_QUIRK(0x103c, 0x8daa, "HP Gemtree", ALC245_FIXUP_TAS2781_SPI_2),
SND_PCI_QUIRK(0x1043, 0x103e, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC),
SND_PCI_QUIRK(0x1043, 0x103f, "ASUS TX300", ALC282_FIXUP_ASUS_TX300),
SND_PCI_QUIRK(0x1043, 0x106d, "Asus K53BE", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
diff --git a/sound/pci/hda/tas2781-spi.h b/sound/pci/hda/tas2781-spi.h
new file mode 100644
index 000000000000..a1bc686a981c
--- /dev/null
+++ b/sound/pci/hda/tas2781-spi.h
@@ -0,0 +1,154 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+//
+// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier
+//
+// Copyright (C) 2024 Texas Instruments Incorporated
+// https://www.ti.com
+//
+// The TAS2781 driver implements a flexible and configurable
+// algo coefficient setting for TAS2781 chips.
+//
+// Author: Baojun Xu <baojun.xu@...com>
+//
+
+#ifndef __TAS2781_SPI_H__
+#define __TAS2781_SPI_H__
+
+#define TASDEVICE_RATES \
+ (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \
+ SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_88200)
+
+#define TASDEVICE_FORMATS \
+ (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE | \
+ SNDRV_PCM_FMTBIT_S32_LE)
+
+#define TASDEVICE_MAX_BOOK_NUM 256
+#define TASDEVICE_MAX_PAGE 256
+
+#define TASDEVICE_MAX_SIZE (TASDEVICE_MAX_BOOK_NUM * TASDEVICE_MAX_PAGE)
+
+/* PAGE Control Register (available in page0 of each book) */
+#define TASDEVICE_PAGE_SELECT 0x00
+#define TASDEVICE_BOOKCTL_PAGE 0x00
+#define TASDEVICE_BOOKCTL_REG GENMASK(7, 1)
+#define TASDEVICE_BOOK_ID(reg) (((reg) & GENMASK(24, 16)) >> 16)
+#define TASDEVICE_PAGE_ID(reg) (((reg) & GENMASK(15, 8)) >> 8)
+#define TASDEVICE_REG_ID(reg) (((reg) & GENMASK(7, 1)) >> 1)
+#define TASDEVICE_PAGE_REG(reg) ((reg) & GENMASK(15, 1))
+#define TASDEVICE_REG(book, page, reg) \
+ (((book) << 16) | ((page) << 8) | ((reg) << 1))
+
+/* Software Reset */
+#define TAS2781_REG_SWRESET TASDEVICE_REG(0x0, 0x0, 0x01)
+#define TAS2781_REG_SWRESET_RESET BIT(0)
+
+/* Block Checksum */
+#define TASDEVICE_CHECKSUM TASDEVICE_REG(0x0, 0x0, 0x7e)
+
+/* Volume control */
+#define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1a)
+#define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03)
+#define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1)
+
+#define TASDEVICE_CMD_SING_W 0x1
+#define TASDEVICE_CMD_BURST 0x2
+#define TASDEVICE_CMD_DELAY 0x3
+#define TASDEVICE_CMD_FIELD_W 0x4
+
+#define TAS2781_SPI_MAX_FREQ (4 * HZ_PER_MHZ)
+
+#define TASDEVICE_CRC8_POLYNOMIAL 0x4d
+#define TASDEVICE_SPEAKER_CALIBRATION_SIZE 20
+
+/* Flag of calibration registers address. */
+#define TASDEVICE_CALIBRATION_REG_ADDRESS BIT(7)
+
+#define TASDEVICE_CALIBRATION_DATA_NAME L"CALI_DATA"
+#define TASDEVICE_CALIBRATION_DATA_SIZE 256
+
+enum calib_data {
+ R0_VAL = 0,
+ INV_R0,
+ R0LOW,
+ POWER,
+ TLIM,
+ CALIB_MAX
+};
+
+struct tasdevice_priv {
+ struct tasdevice_fw *cali_data_fmw;
+ struct tasdevice_rca rcabin;
+ struct tasdevice_fw *fmw;
+ struct gpio_desc *reset;
+ struct mutex codec_lock;
+ struct regmap *regmap;
+ struct device *dev;
+ struct tm tm;
+
+ const char *acpi_subsystem_id;
+ unsigned char crc8_lkp_tbl[CRC8_TABLE_SIZE];
+ unsigned char coef_binaryname[64];
+ unsigned char rca_binaryname[64];
+ unsigned char dev_name[32];
+
+ unsigned int err_code;
+ bool is_loading;
+ bool is_loaderr;
+ int cur_book;
+ int cur_prog;
+ int cur_conf;
+ int fw_state;
+ int index;
+ int irq;
+ void *codec;
+ bool force_fwload_status;
+ bool playback_started;
+ unsigned int cali_data[CALIB_MAX];
+ unsigned int cali_reg_array[CALIB_MAX];
+
+ int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv,
+ const struct firmware *fmw,
+ int offset);
+ int (*fw_parse_program_data)(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw,
+ const struct firmware *fmw, int offset);
+ int (*fw_parse_configuration_data)(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw,
+ const struct firmware *fmw,
+ int offset);
+ int (*tasdevice_load_block)(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block);
+
+ int (*save_calibration)(struct tasdevice_priv *tas_priv);
+ void (*apply_calibration)(struct tasdevice_priv *tas_priv);
+};
+
+int tasdevice_spi_dev_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int *value);
+int tasdevice_spi_dev_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int value);
+int tasdevice_spi_dev_bulk_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned char *p_data,
+ unsigned int n_length);
+int tasdevice_spi_dev_bulk_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned char *p_data,
+ unsigned int n_length);
+int tasdevice_spi_dev_update_bits(struct tasdevice_priv *tasdevice,
+ unsigned int reg, unsigned int mask,
+ unsigned int value);
+
+void tasdevice_spi_select_cfg_blk(void *context, int conf_no,
+ unsigned char block_type);
+void tasdevice_spi_config_info_remove(void *context);
+int tasdevice_spi_dsp_parser(void *context);
+int tasdevice_spi_rca_parser(void *context, const struct firmware *fmw);
+void tasdevice_spi_dsp_remove(void *context);
+void tasdevice_spi_calbin_remove(void *context);
+int tasdevice_spi_select_tuningprm_cfg(void *context, int prm, int cfg_no,
+ int rca_conf_no);
+int tasdevice_spi_prmg_load(void *context, int prm_no);
+int tasdevice_spi_prmg_calibdata_load(void *context, int prm_no);
+void tasdevice_spi_tuning_switch(void *context, int state);
+int tas2781_spi_load_calibration(void *context, char *file_name,
+ unsigned short i);
+#endif /* __TAS2781_SPI_H__ */
diff --git a/sound/pci/hda/tas2781_hda_spi.c b/sound/pci/hda/tas2781_hda_spi.c
new file mode 100644
index 000000000000..490d5aca865c
--- /dev/null
+++ b/sound/pci/hda/tas2781_hda_spi.c
@@ -0,0 +1,1266 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// TAS2781 HDA SPI driver
+//
+// Copyright 2024 Texas Instruments, Inc.
+//
+// Author: Baojun Xu <baojun.xu@...com>
+
+#include <linux/acpi.h>
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/cleanup.h>
+#include <linux/crc8.h>
+#include <linux/crc32.h>
+#include <linux/efi.h>
+#include <linux/firmware.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/time.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+#include <sound/hda_codec.h>
+#include <sound/soc.h>
+#include <sound/tas2781-dsp.h>
+#include <sound/tlv.h>
+#include <sound/tas2781-tlv.h>
+
+#include "tas2781-spi.h"
+
+#include "hda_local.h"
+#include "hda_auto_parser.h"
+#include "hda_component.h"
+#include "hda_jack.h"
+#include "hda_generic.h"
+
+/*
+ * No standard control callbacks for SNDRV_CTL_ELEM_IFACE_CARD
+ * Define two controls, one is Volume control callbacks, the other is
+ * flag setting control callbacks.
+ */
+
+/* Volume control callbacks for tas2781 */
+#define ACARD_SINGLE_RANGE_EXT_TLV(xname, xreg, xshift, xmin, xmax, xinvert, \
+ xhandler_get, xhandler_put, tlv_array) { \
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD, .name = (xname), \
+ .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \
+ SNDRV_CTL_ELEM_ACCESS_READWRITE, \
+ .tlv.p = (tlv_array), \
+ .info = snd_soc_info_volsw_range, \
+ .get = xhandler_get, .put = xhandler_put, \
+ .private_value = (unsigned long)&(struct soc_mixer_control) { \
+ .reg = xreg, .rreg = xreg, \
+ .shift = xshift, .rshift = xshift,\
+ .min = xmin, .max = xmax, .invert = xinvert, \
+ } \
+}
+
+/* Flag control callbacks for tas2781 */
+#define ACARD_SINGLE_BOOL_EXT(xname, xdata, xhandler_get, xhandler_put) { \
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD, \
+ .name = xname, \
+ .info = snd_ctl_boolean_mono_info, \
+ .get = xhandler_get, \
+ .put = xhandler_put, \
+ .private_value = xdata, \
+}
+
+struct tas2781_hda {
+ struct tasdevice_priv *priv;
+ struct acpi_device *dacpi;
+ struct snd_kcontrol *dsp_prog_ctl;
+ struct snd_kcontrol *dsp_conf_ctl;
+ struct snd_kcontrol *snd_ctls[3];
+ struct snd_kcontrol *prof_ctl;
+};
+
+static const struct regmap_range_cfg tasdevice_ranges[] = {
+ {
+ .range_min = 0,
+ .range_max = TASDEVICE_MAX_SIZE,
+ .selector_reg = TASDEVICE_PAGE_SELECT,
+ .selector_mask = GENMASK(7, 0),
+ .selector_shift = 0,
+ .window_start = 0,
+ .window_len = TASDEVICE_MAX_PAGE,
+ },
+};
+
+static const struct regmap_config tasdevice_regmap = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .zero_flag_mask = true,
+ .cache_type = REGCACHE_NONE,
+ .ranges = tasdevice_ranges,
+ .num_ranges = ARRAY_SIZE(tasdevice_ranges),
+ .max_register = TASDEVICE_MAX_SIZE,
+};
+
+static int tasdevice_spi_switch_book(struct tasdevice_priv *tas_priv, int reg)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ if (tas_priv->cur_book != TASDEVICE_BOOK_ID(reg)) {
+ ret = regmap_write(map, TASDEVICE_BOOKCTL_REG,
+ TASDEVICE_BOOK_ID(reg));
+ if (ret < 0) {
+ dev_err(tas_priv->dev, "Switch Book E=%d\n", ret);
+ return ret;
+ }
+ tas_priv->cur_book = TASDEVICE_BOOK_ID(reg);
+ }
+ return ret;
+}
+
+int tasdevice_spi_dev_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg,
+ unsigned int *val)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, reg);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * In our TAS2781 SPI mode, if read from other book (not book 0),
+ * or read from page number larger than 1 in book 0, one more byte
+ * read is needed, and first byte is a dummy byte, need to be ignored.
+ */
+ if ((TASDEVICE_BOOK_ID(reg) > 0) || (TASDEVICE_PAGE_ID(reg) > 1)) {
+ unsigned char data[2];
+
+ ret = regmap_bulk_read(map, TASDEVICE_PAGE_REG(reg) | 1,
+ data, sizeof(data));
+ *val = data[1];
+ } else {
+ ret = regmap_read(map, TASDEVICE_PAGE_REG(reg) | 1, val);
+ }
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg,
+ unsigned int value)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_write(map, TASDEVICE_PAGE_REG(reg), value);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_bulk_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg,
+ unsigned char *data,
+ unsigned int len)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_bulk_write(map, TASDEVICE_PAGE_REG(reg), data, len);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_bulk_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg,
+ unsigned char *data,
+ unsigned int len)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, reg);
+ if (ret < 0)
+ return ret;
+
+ if (len > TASDEVICE_MAX_PAGE)
+ len = TASDEVICE_MAX_PAGE;
+ /*
+ * In our TAS2781 SPI mode, if read from other book (not book 0),
+ * or read from page number larger than 1 in book 0, one more byte
+ * read is needed, and first byte is a dummy byte, need to be ignored.
+ */
+ if ((TASDEVICE_BOOK_ID(reg) > 0) || (TASDEVICE_PAGE_ID(reg) > 1)) {
+ unsigned char buf[TASDEVICE_MAX_PAGE+1];
+
+ ret = regmap_bulk_read(map, TASDEVICE_PAGE_REG(reg) | 1, buf,
+ len + 1);
+ memcpy(data, buf + 1, len);
+ } else {
+ ret = regmap_bulk_read(map, TASDEVICE_PAGE_REG(reg) | 1, data,
+ len);
+ }
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_update_bits(struct tasdevice_priv *tas_priv,
+ unsigned int reg,
+ unsigned int mask,
+ unsigned int value)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret, val;
+
+ /*
+ * In our TAS2781 SPI mode, read/write was masked in last bit of
+ * address, it cause regmap_update_bits() not work as expected.
+ */
+ ret = tasdevice_spi_dev_read(tas_priv, reg, &val);
+ if (ret < 0) {
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+ return ret;
+ }
+ ret = regmap_write(map, TASDEVICE_PAGE_REG(reg),
+ (val & ~mask) | (mask & value));
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+static void tas2781_spi_reset(struct tasdevice_priv *tas_dev)
+{
+ if (tas_dev->reset) {
+ gpiod_set_value_cansleep(tas_dev->reset, 0);
+ fsleep(800);
+ gpiod_set_value_cansleep(tas_dev->reset, 1);
+ }
+ fsleep(1000);
+}
+
+static int tascodec_spi_init(struct tasdevice_priv *tas_priv,
+ void *codec, struct module *module,
+ void (*cont)(const struct firmware *fw, void *context))
+{
+ int ret;
+
+ /*
+ * Codec Lock Hold to ensure that codec_probe and firmware parsing and
+ * loading do not simultaneously execute.
+ */
+ guard(mutex)(&tas_priv->codec_lock);
+
+ ret = scnprintf(tas_priv->rca_binaryname,
+ sizeof(tas_priv->rca_binaryname), "%sRCA%d.bin",
+ tas_priv->dev_name, tas_priv->index);
+ if (ret <= 0) {
+ dev_err(tas_priv->dev, "rca name err:0x%08x\n", ret);
+ return ret;
+ }
+ crc8_populate_msb(tas_priv->crc8_lkp_tbl, TASDEVICE_CRC8_POLYNOMIAL);
+ tas_priv->codec = codec;
+ ret = request_firmware_nowait(module, FW_ACTION_UEVENT,
+ tas_priv->rca_binaryname, tas_priv->dev, GFP_KERNEL, tas_priv,
+ cont);
+ if (ret)
+ dev_err(tas_priv->dev, "request_firmware_nowait err:0x%08x\n",
+ ret);
+
+ return ret;
+}
+
+static void tasdevice_spi_init(struct tasdevice_priv *tas_priv)
+{
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ tas_priv->cur_book = -1;
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ /* Store default registers address for calibration data. */
+ tas_priv->cali_reg_array[0] = TASDEVICE_REG(0, 0x17, 0x74);
+ tas_priv->cali_reg_array[1] = TASDEVICE_REG(0, 0x18, 0x0c);
+ tas_priv->cali_reg_array[2] = TASDEVICE_REG(0, 0x18, 0x14);
+ tas_priv->cali_reg_array[3] = TASDEVICE_REG(0, 0x13, 0x70);
+ tas_priv->cali_reg_array[4] = TASDEVICE_REG(0, 0x18, 0x7c);
+
+ mutex_init(&tas_priv->codec_lock);
+}
+
+static int tasdevice_spi_amp_putvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol,
+ struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ unsigned char mask;
+ int max = mc->max;
+ int val, ret;
+
+ mask = rounddown_pow_of_two(max);
+ mask <<= mc->shift;
+ val = clamp(invert ? max - ucontrol->value.integer.value[0] :
+ ucontrol->value.integer.value[0], 0, max);
+ ret = tasdevice_spi_dev_update_bits(tas_priv,
+ mc->reg, mask, (unsigned int)(val << mc->shift));
+ if (ret)
+ dev_err(tas_priv->dev, "set AMP vol error in dev %d\n",
+ tas_priv->index);
+
+ return ret;
+}
+
+static int tasdevice_spi_amp_getvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol,
+ struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ unsigned char mask = 0;
+ int max = mc->max;
+ int ret, val;
+
+ /* Read the primary device */
+ ret = tasdevice_spi_dev_read(tas_priv, mc->reg, &val);
+ if (ret) {
+ dev_err(tas_priv->dev, "%s, get AMP vol error\n", __func__);
+ return ret;
+ }
+
+ mask = rounddown_pow_of_two(max);
+ mask <<= mc->shift;
+ val = (val & mask) >> mc->shift;
+ val = clamp(invert ? max - val : val, 0, max);
+ ucontrol->value.integer.value[0] = val;
+
+ return ret;
+}
+
+static int tasdevice_spi_digital_putvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol,
+ struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ int max = mc->max;
+ int val, ret;
+
+ val = clamp(invert ? max - ucontrol->value.integer.value[0] :
+ ucontrol->value.integer.value[0], 0, max);
+ ret = tasdevice_spi_dev_write(tas_priv, mc->reg, (unsigned int)val);
+ if (ret)
+ dev_err(tas_priv->dev, "set digital vol err in dev %d\n",
+ tas_priv->index);
+
+ return ret;
+}
+
+static int tasdevice_spi_digital_getvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol,
+ struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ int max = mc->max;
+ int ret, val;
+
+ /* Read the primary device as the whole */
+ ret = tasdevice_spi_dev_read(tas_priv, mc->reg, &val);
+ if (ret) {
+ dev_err(tas_priv->dev, "%s, get digital vol err\n", __func__);
+ return ret;
+ }
+
+ val = clamp(invert ? max - val : val, 0, max);
+ ucontrol->value.integer.value[0] = val;
+
+ return ret;
+}
+
+static int tas2781_read_acpi(struct tas2781_hda *tas_hda,
+ const char *hid,
+ int id)
+{
+ struct tasdevice_priv *p = tas_hda->priv;
+ struct acpi_device *adev;
+ struct device *physdev;
+ u32 values[HDA_MAX_COMPONENTS];
+ const char *property;
+ size_t nval;
+ int ret, i;
+
+ adev = acpi_dev_get_first_match_dev(hid, NULL, -1);
+ if (!adev) {
+ dev_err(p->dev, "Failed to find ACPI device: %s\n", hid);
+ return -ENODEV;
+ }
+
+ strscpy(p->dev_name, hid, sizeof(p->dev_name));
+ tas_hda->dacpi = adev;
+ physdev = get_device(acpi_get_first_physical_node(adev));
+ acpi_dev_put(adev);
+
+ /* No side-effect to the playback even if subsystem_id is NULL */
+ p->acpi_subsystem_id = acpi_get_subsystem_id(ACPI_HANDLE(physdev));
+
+ property = "ti,dev-index";
+ ret = device_property_count_u32(physdev, property);
+ if (ret <= 0 || ret > ARRAY_SIZE(values)) {
+ ret = -EINVAL;
+ goto err;
+ }
+ nval = ret;
+
+ ret = device_property_read_u32_array(physdev, property, values, nval);
+ if (ret)
+ goto err;
+
+ p->index = U8_MAX;
+ for (i = 0; i < nval; i++) {
+ if (values[i] == id) {
+ p->index = i;
+ break;
+ }
+ }
+ if (p->index == U8_MAX) {
+ dev_dbg(p->dev, "No index found in %s\n", property);
+ ret = -ENODEV;
+ goto err;
+ }
+
+ if (p->index == 0) {
+ /* All of amps share same RESET pin. */
+ p->reset = devm_gpiod_get_index_optional(physdev, "reset",
+ p->index, GPIOD_OUT_LOW);
+ if (IS_ERR(p->reset)) {
+ dev_err_probe(p->dev, ret, "Failed on reset GPIO\n");
+ goto err;
+ }
+ }
+ put_device(physdev);
+
+ return 0;
+err:
+ dev_err(p->dev, "read acpi error, ret: %d\n", ret);
+ put_device(physdev);
+ acpi_dev_put(adev);
+
+ return ret;
+}
+
+static void tas2781_hda_playback_hook(struct device *dev, int action)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ if (action == HDA_GEN_PCM_ACT_OPEN) {
+ pm_runtime_get_sync(dev);
+ guard(mutex)(&tas_hda->priv->codec_lock);
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+ } else if (action == HDA_GEN_PCM_ACT_CLOSE) {
+ guard(mutex)(&tas_hda->priv->codec_lock);
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+ }
+}
+
+static int tasdevice_info_profile(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->rcabin.ncfgs - 1;
+
+ return 0;
+}
+
+static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id;
+
+ return 0;
+}
+
+static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int max = tas_priv->rcabin.ncfgs - 1;
+ int val;
+
+ val = clamp(ucontrol->value.integer.value[0], 0, max);
+ if (tas_priv->rcabin.profile_cfg_id != val) {
+ tas_priv->rcabin.profile_cfg_id = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+static int tasdevice_info_programs(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->fmw->nr_programs - 1;
+
+ return 0;
+}
+
+static int tasdevice_info_config(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->fmw->nr_configurations - 1;
+
+ return 0;
+}
+
+static int tasdevice_program_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_prog;
+
+ return 0;
+}
+
+static int tasdevice_program_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int nr_program = ucontrol->value.integer.value[0];
+ int max = tas_priv->fmw->nr_programs - 1;
+ int val;
+
+ val = clamp(nr_program, 0, max);
+
+ if (tas_priv->cur_prog != val) {
+ tas_priv->cur_prog = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+static int tasdevice_config_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_conf;
+
+ return 0;
+}
+
+static int tasdevice_config_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int max = tas_priv->fmw->nr_configurations - 1;
+ int val;
+
+ val = clamp(ucontrol->value.integer.value[0], 0, max);
+
+ if (tas_priv->cur_conf != val) {
+ tas_priv->cur_conf = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+/*
+ * tas2781_digital_getvol - get the volum control
+ * @kcontrol: control pointer
+ * @ucontrol: User data
+ *
+ * Customer Kcontrol for tas2781 is primarily for regmap booking, paging
+ * depends on internal regmap mechanism.
+ * tas2781 contains book and page two-level register map, especially
+ * book switching will set the register BXXP00R7F, after switching to the
+ * correct book, then leverage the mechanism for paging to access the
+ * register.
+ *
+ * Return 0 if succeeded.
+ */
+static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_spi_digital_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_spi_amp_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ /* The check of the given value is in tasdevice_digital_putvol. */
+ return tasdevice_spi_digital_putvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ /* The check of the given value is in tasdevice_amp_putvol. */
+ return tasdevice_spi_amp_putvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_force_fwload_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = (int)tas_priv->force_fwload_status;
+ dev_dbg(tas_priv->dev, "%s : Force FWload %s\n", __func__,
+ str_on_off(tas_priv->force_fwload_status));
+
+ return 0;
+}
+
+static int tas2781_force_fwload_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ bool change, val = (bool)ucontrol->value.integer.value[0];
+
+ if (tas_priv->force_fwload_status == val) {
+ change = false;
+ } else {
+ change = true;
+ tas_priv->force_fwload_status = val;
+ }
+ dev_dbg(tas_priv->dev, "%s : Force FWload %s\n", __func__,
+ str_on_off(tas_priv->force_fwload_status));
+
+ return change;
+}
+
+static const struct snd_kcontrol_new tas2781_snd_controls[] = {
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Analog Gain 0", TAS2781_AMP_LEVEL,
+ 1, 0, 20, 0, tas2781_amp_getvol,
+ tas2781_amp_putvol, amp_vol_tlv),
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Digital Gain 0", TAS2781_DVC_LVL,
+ 0, 0, 200, 1, tas2781_digital_getvol,
+ tas2781_digital_putvol, dvc_tlv),
+ ACARD_SINGLE_BOOL_EXT("Speaker Force Firmware Load 0", 0,
+ tas2781_force_fwload_get, tas2781_force_fwload_put),
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Analog Gain 1", TAS2781_AMP_LEVEL,
+ 1, 0, 20, 0, tas2781_amp_getvol,
+ tas2781_amp_putvol, amp_vol_tlv),
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Digital Gain 1", TAS2781_DVC_LVL,
+ 0, 0, 200, 1, tas2781_digital_getvol,
+ tas2781_digital_putvol, dvc_tlv),
+ ACARD_SINGLE_BOOL_EXT("Speaker Force Firmware Load 1", 0,
+ tas2781_force_fwload_get, tas2781_force_fwload_put),
+};
+
+static const struct snd_kcontrol_new tas2781_prof_ctrl[] = {
+{
+ .name = "Speaker Profile Id - 0",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_profile,
+ .get = tasdevice_get_profile_id,
+ .put = tasdevice_set_profile_id,
+},
+{
+ .name = "Speaker Profile Id - 1",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_profile,
+ .get = tasdevice_get_profile_id,
+ .put = tasdevice_set_profile_id,
+},
+};
+static const struct snd_kcontrol_new tas2781_dsp_prog_ctrl[] = {
+{
+ .name = "Speaker Program Id 0",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_programs,
+ .get = tasdevice_program_get,
+ .put = tasdevice_program_put,
+},
+{
+ .name = "Speaker Program Id 1",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_programs,
+ .get = tasdevice_program_get,
+ .put = tasdevice_program_put,
+},
+};
+
+static const struct snd_kcontrol_new tas2781_dsp_conf_ctrl[] = {
+{
+ .name = "Speaker Config Id 0",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_config,
+ .get = tasdevice_config_get,
+ .put = tasdevice_config_put,
+},
+{
+ .name = "Speaker Config Id 1",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_config,
+ .get = tasdevice_config_get,
+ .put = tasdevice_config_put,
+},
+};
+
+static void tas2781_apply_calib(struct tasdevice_priv *tas_priv)
+{
+ int j, rc;
+
+ /*
+ * If no calibration data exist in tasdevice_priv *tas_priv,
+ * calibration apply will be ignored, and use default values
+ * in firmware binary, which was loaded during firmware download.
+ */
+ if (tas_priv->cali_data[0] == 0)
+ return;
+ /*
+ * Calibration data was saved in tasdevice_priv *tas_priv as:
+ * unsigned int cali_data[CALIB_MAX];
+ * and every data (in 4 bytes) will be saved in register which in
+ * book 0, and page number in page_array[], offset was saved in
+ * rgno_array[].
+ */
+ for (j = 0; j < CALIB_MAX; j++) {
+ rc = tasdevice_spi_dev_bulk_write(tas_priv,
+ tas_priv->cali_reg_array[j],
+ (unsigned char *)&tas_priv->cali_data[j], 4);
+ if (rc < 0)
+ dev_err(tas_priv->dev,
+ "chn %d calib %d bulk_wr err = %d\n",
+ tas_priv->index, j, rc);
+ }
+}
+
+/*
+ * Update the calibration data, including speaker impedance, f0, etc,
+ * into algo. Calibrate data is done by manufacturer in the factory.
+ * These data are used by Algo for calculating the speaker temperature,
+ * speaker membrane excursion and f0 in real time during playback.
+ * Calibration data format in EFI is V2, since 2024.
+ */
+static int tas2781_save_calibration(struct tasdevice_priv *tas_priv)
+{
+ /*
+ * GUID was used for data access in BIOS, it was provided by board
+ * manufactory, like HP: "{02f9af02-7734-4233-b43d-93fe5aa35db3}"
+ */
+ efi_guid_t efi_guid =
+ EFI_GUID(0x02f9af02, 0x7734, 0x4233,
+ 0xb4, 0x3d, 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3);
+ static efi_char16_t efi_name[] = TASDEVICE_CALIBRATION_DATA_NAME;
+ unsigned char data[TASDEVICE_CALIBRATION_DATA_SIZE], *buf;
+ unsigned int attr, crc, offset, *tmp_val;
+ struct tm *tm = &tas_priv->tm;
+ unsigned long total_sz = 0;
+ efi_status_t status;
+
+ tas_priv->cali_data[0] = 0;
+ status = efi.get_variable(efi_name, &efi_guid, &attr, &total_sz, data);
+ if (status == EFI_BUFFER_TOO_SMALL) {
+ if (total_sz > TASDEVICE_CALIBRATION_DATA_SIZE)
+ return -ENOMEM;
+ /* Get variable contents into buffer */
+ status = efi.get_variable(efi_name, &efi_guid, &attr,
+ &total_sz, data);
+ }
+ if (status != EFI_SUCCESS)
+ return -EINVAL;
+
+ tmp_val = (unsigned int *)data;
+ if (tmp_val[0] == 2781) {
+ /*
+ * New features were added in calibrated Data V3:
+ * 1. Added calibration registers address define in
+ * a node, marked as Device id == 0x80.
+ * New features were added in calibrated Data V2:
+ * 1. Added some the fields to store the link_id and
+ * uniqie_id for multi-link solutions
+ * 2. Support flexible number of devices instead of
+ * fixed one in V1.
+ * Layout of calibrated data V2 in UEFI(total 256 bytes):
+ * ChipID (2781, 4 bytes)
+ * Device-Sum (4 bytes)
+ * TimeStamp of Calibration (4 bytes)
+ * for (i = 0; i < Device-Sum; i++) {
+ * Device #i index_info () {
+ * SDW link id (2bytes)
+ * SDW unique_id (2bytes)
+ * } // if Device number is 0x80, mean it's
+ * calibration registers address.
+ * Calibrated Data of Device #i (20 bytes)
+ * }
+ * CRC (4 bytes)
+ * Reserved (the rest)
+ */
+ crc = crc32(~0, data, (3 + tmp_val[1] * 6) * 4) ^ ~0;
+
+ if (crc == tmp_val[3 + tmp_val[1] * 6]) {
+ time64_to_tm(tmp_val[2], 0, tm);
+ for (int j = 0; j < tmp_val[1]; j++) {
+ offset = j * 6 + 3;
+ if (tmp_val[offset] == tas_priv->index) {
+ for (int i = 0; i < CALIB_MAX; i++)
+ tas_priv->cali_data[i] =
+ tmp_val[offset + i];
+ } else if (tmp_val[offset] ==
+ TASDEVICE_CALIBRATION_REG_ADDRESS) {
+ for (int i = 0; i < CALIB_MAX; i++) {
+ buf = &data[(offset + i) * 4];
+ tas_priv->cali_reg_array[i] =
+ TASDEVICE_REG(buf[1], buf[2],
+ buf[3]);
+ }
+ }
+ }
+ tas_priv->apply_calibration(tas_priv);
+ }
+ } else {
+ /*
+ * Calibration data is in V1 format.
+ * struct cali_data {
+ * char cali_data[20];
+ * }
+ *
+ * struct {
+ * struct cali_data cali_data[4];
+ * int TimeStamp of Calibration (4 bytes)
+ * int CRC (4 bytes)
+ * } ueft;
+ */
+ crc = crc32(~0, data, 84) ^ ~0;
+ if (crc == tmp_val[21]) {
+ time64_to_tm(tmp_val[20], 0, tm);
+ for (int i = 0; i < CALIB_MAX; i++)
+ tas_priv->cali_data[i] =
+ tmp_val[tas_priv->index * 5 + i];
+ tas_priv->apply_calibration(tas_priv);
+ }
+ }
+
+ return 0;
+}
+
+static void tas2781_hda_remove_controls(struct tas2781_hda *tas_hda)
+{
+ struct hda_codec *codec = tas_hda->priv->codec;
+
+ if (tas_hda->dsp_prog_ctl)
+ snd_ctl_remove(codec->card, tas_hda->dsp_prog_ctl);
+
+ if (tas_hda->dsp_conf_ctl)
+ snd_ctl_remove(codec->card, tas_hda->dsp_conf_ctl);
+
+ for (int i = ARRAY_SIZE(tas_hda->snd_ctls) - 1; i >= 0; i--)
+ if (tas_hda->snd_ctls[i])
+ snd_ctl_remove(codec->card, tas_hda->snd_ctls[i]);
+
+ if (tas_hda->prof_ctl)
+ snd_ctl_remove(codec->card, tas_hda->prof_ctl);
+}
+
+static void tasdev_fw_ready(const struct firmware *fmw, void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tas2781_hda *tas_hda = dev_get_drvdata(tas_priv->dev);
+ struct hda_codec *codec = tas_priv->codec;
+ int i, j, ret;
+
+ pm_runtime_get_sync(tas_priv->dev);
+ guard(mutex)(&tas_priv->codec_lock);
+
+ ret = tasdevice_spi_rca_parser(tas_priv, fmw);
+ if (ret)
+ goto out;
+
+ /* Add control one time only. */
+ tas_hda->prof_ctl = snd_ctl_new1(&tas2781_prof_ctrl[tas_priv->index],
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->prof_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",
+ tas2781_prof_ctrl[tas_priv->index].name, ret);
+ goto out;
+ }
+ j = tas_priv->index * ARRAY_SIZE(tas2781_snd_controls)/2;
+ for (i = 0; i < ARRAY_SIZE(tas2781_snd_controls)/2; i++) {
+ tas_hda->snd_ctls[i] = snd_ctl_new1(&tas2781_snd_controls[i+j],
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->snd_ctls[i]);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_snd_controls[i+tas_priv->index*3].name,
+ ret);
+ goto out;
+ }
+ }
+
+ tasdevice_spi_dsp_remove(tas_priv);
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+ scnprintf(tas_priv->coef_binaryname, 64, "TAS2XXX%08X-%01d.bin",
+ codec->core.subsystem_id, tas_priv->index);
+ ret = tasdevice_spi_dsp_parser(tas_priv);
+ if (ret) {
+ dev_err(tas_priv->dev, "dspfw load %s error\n",
+ tas_priv->coef_binaryname);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ goto out;
+ }
+
+ /* Add control one time only. */
+ tas_hda->dsp_prog_ctl =
+ snd_ctl_new1(&tas2781_dsp_prog_ctrl[tas_priv->index],
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->dsp_prog_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_dsp_prog_ctrl[tas_priv->index].name, ret);
+ goto out;
+ }
+
+ tas_hda->dsp_conf_ctl =
+ snd_ctl_new1(&tas2781_dsp_conf_ctrl[tas_priv->index],
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->dsp_conf_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",
+ tas2781_dsp_conf_ctrl[tas_priv->index].name, ret);
+ goto out;
+ }
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK;
+ tasdevice_spi_prmg_load(tas_priv, 0);
+ if (tas_priv->fmw->nr_programs > 0)
+ tas_priv->cur_prog = 0;
+ if (tas_priv->fmw->nr_configurations > 0)
+ tas_priv->cur_conf = 0;
+
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+
+ /*
+ * If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ tas_priv->save_calibration(tas_priv);
+
+out:
+ if (fmw)
+ release_firmware(fmw);
+ pm_runtime_mark_last_busy(tas_hda->priv->dev);
+ pm_runtime_put_autosuspend(tas_hda->priv->dev);
+}
+
+static int tas2781_hda_bind(struct device *dev, struct device *master,
+ void *master_data)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+ struct hda_codec *codec;
+ int ret;
+
+ if (tas_hda->priv->index < 0 ||
+ tas_hda->priv->index >= HDA_MAX_COMPONENTS ||
+ !comps)
+ return -EINVAL;
+
+ comps = &comps[tas_hda->priv->index];
+ if (comps->dev)
+ return -EBUSY;
+
+ codec = comps->codec;
+
+ pm_runtime_get_sync(dev);
+
+ comps->dev = dev;
+
+ strscpy(comps->name, dev_name(dev), sizeof(comps->name));
+
+ ret = tascodec_spi_init(tas_hda->priv, codec, THIS_MODULE,
+ tasdev_fw_ready);
+ if (!ret)
+ comps->playback_hook = tas2781_hda_playback_hook;
+
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+
+ return ret;
+}
+
+static void tas2781_hda_unbind(struct device *dev, struct device *master,
+ void *master_data)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+
+ comps = &comps[tas_hda->priv->index];
+
+ if (comps->dev == dev) {
+ comps->dev = NULL;
+ memset(comps->name, 0, sizeof(comps->name));
+ comps->playback_hook = NULL;
+ }
+
+ tas2781_hda_remove_controls(tas_hda);
+
+ tasdevice_spi_config_info_remove(tas_hda->priv);
+ tasdevice_spi_dsp_remove(tas_hda->priv);
+
+ tas_hda->priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+}
+
+static const struct component_ops tas2781_hda_comp_ops = {
+ .bind = tas2781_hda_bind,
+ .unbind = tas2781_hda_unbind,
+};
+
+static void tas2781_hda_remove(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ component_del(tas_hda->priv->dev, &tas2781_hda_comp_ops);
+
+ pm_runtime_get_sync(tas_hda->priv->dev);
+ pm_runtime_disable(tas_hda->priv->dev);
+
+ pm_runtime_put_noidle(tas_hda->priv->dev);
+
+ mutex_destroy(&tas_hda->priv->codec_lock);
+}
+
+static int tas2781_hda_spi_probe(struct spi_device *spi)
+{
+ struct tasdevice_priv *tas_priv;
+ struct tas2781_hda *tas_hda;
+ const char *device_name;
+ int ret = 0;
+
+ tas_hda = devm_kzalloc(&spi->dev, sizeof(*tas_hda), GFP_KERNEL);
+ if (!tas_hda)
+ return -ENOMEM;
+
+ spi->max_speed_hz = TAS2781_SPI_MAX_FREQ;
+
+ tas_priv = devm_kzalloc(&spi->dev, sizeof(*tas_priv), GFP_KERNEL);
+ if (!tas_priv)
+ goto err;
+ tas_priv->dev = &spi->dev;
+ tas_hda->priv = tas_priv;
+ tas_priv->regmap = devm_regmap_init_spi(spi, &tasdevice_regmap);
+ if (IS_ERR(tas_priv->regmap)) {
+ ret = PTR_ERR(tas_priv->regmap);
+ dev_err(tas_priv->dev, "Failed to allocate regmap: %d\n",
+ ret);
+ goto err;
+ }
+ if (strstr(dev_name(&spi->dev), "TXNW2781")) {
+ device_name = "TXNW2781";
+ tas_priv->save_calibration = tas2781_save_calibration;
+ tas_priv->apply_calibration = tas2781_apply_calib;
+ } else {
+ goto err;
+ }
+
+ tas_priv->irq = spi->irq;
+ dev_set_drvdata(&spi->dev, tas_hda);
+ ret = tas2781_read_acpi(tas_hda, device_name,
+ spi_get_chipselect(spi, 0));
+ if (ret)
+ return dev_err_probe(tas_priv->dev, ret,
+ "Platform not supported\n");
+
+ tasdevice_spi_init(tas_priv);
+
+ pm_runtime_set_autosuspend_delay(tas_priv->dev, 3000);
+ pm_runtime_use_autosuspend(tas_priv->dev);
+ pm_runtime_mark_last_busy(tas_priv->dev);
+ pm_runtime_set_active(tas_priv->dev);
+ pm_runtime_get_noresume(tas_priv->dev);
+ pm_runtime_enable(tas_priv->dev);
+
+ pm_runtime_put_autosuspend(tas_priv->dev);
+
+ tas2781_spi_reset(tas_priv);
+
+ ret = component_add(tas_priv->dev, &tas2781_hda_comp_ops);
+ if (ret) {
+ dev_err(tas_priv->dev, "Register component fail: %d\n", ret);
+ pm_runtime_disable(tas_priv->dev);
+ }
+
+err:
+ if (ret)
+ tas2781_hda_remove(&spi->dev);
+
+ return ret;
+}
+
+static void tas2781_hda_spi_remove(struct spi_device *spi)
+{
+ tas2781_hda_remove(&spi->dev);
+}
+
+static int tas2781_runtime_suspend(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ if (tas_hda->priv->playback_started) {
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+ tas_hda->priv->playback_started = false;
+ }
+
+ tas_hda->priv->cur_book = -1;
+ tas_hda->priv->cur_conf = -1;
+
+ return 0;
+}
+
+static int tas2781_runtime_resume(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ tasdevice_spi_prmg_load(tas_hda->priv, tas_hda->priv->cur_prog);
+
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+
+ tas_hda->priv->apply_calibration(tas_hda->priv);
+
+ return 0;
+}
+
+static int tas2781_system_suspend(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ return ret;
+
+ /* Shutdown chip before system suspend */
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+
+ /*
+ * Reset GPIO may be shared, so cannot reset here.
+ * However beyond this point, amps may be powered down.
+ */
+ return 0;
+}
+
+static int tas2781_system_resume(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ tas_hda->priv->cur_book = -1;
+ tas_hda->priv->cur_conf = -1;
+
+ tas2781_spi_reset(tas_hda->priv);
+ tasdevice_spi_prmg_load(tas_hda->priv, tas_hda->priv->cur_prog);
+
+ if (tas_hda->priv->playback_started)
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+ /*
+ * If calibrated data occurs error, dsp will still work with default
+ * calibrated data inside algo.
+ */
+ tas_hda->priv->apply_calibration(tas_hda->priv);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tas2781_hda_pm_ops = {
+ RUNTIME_PM_OPS(tas2781_runtime_suspend, tas2781_runtime_resume, NULL)
+ SYSTEM_SLEEP_PM_OPS(tas2781_system_suspend, tas2781_system_resume)
+};
+
+static const struct spi_device_id tas2781_hda_spi_id[] = {
+ { "tas2781-hda", },
+ {}
+};
+
+static const struct acpi_device_id tas2781_acpi_hda_match[] = {
+ {"TXNW2781", },
+ {}
+};
+MODULE_DEVICE_TABLE(acpi, tas2781_acpi_hda_match);
+
+static struct spi_driver tas2781_hda_spi_driver = {
+ .driver = {
+ .name = "tas2781-hda",
+ .acpi_match_table = tas2781_acpi_hda_match,
+ .pm = &tas2781_hda_pm_ops,
+ },
+ .id_table = tas2781_hda_spi_id,
+ .probe = tas2781_hda_spi_probe,
+ .remove = tas2781_hda_spi_remove,
+};
+module_spi_driver(tas2781_hda_spi_driver);
+
+MODULE_DESCRIPTION("TAS2781 HDA SPI Driver");
+MODULE_AUTHOR("Baojun, Xu, <baojun.xug@...com>");
+MODULE_LICENSE("GPL");
diff --git a/sound/pci/hda/tas2781_spi_fwlib.c b/sound/pci/hda/tas2781_spi_fwlib.c
new file mode 100644
index 000000000000..e4a415de9178
--- /dev/null
+++ b/sound/pci/hda/tas2781_spi_fwlib.c
@@ -0,0 +1,2111 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// TAS2781 HDA SPI driver
+//
+// Copyright 2024 Texas Instruments, Inc.
+//
+// Author: Baojun Xu <baojun.xu@...com>
+
+#include <asm/unaligned.h>
+#include <linux/crc8.h>
+#include <linux/firmware.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/tas2781-dsp.h>
+#include <sound/tlv.h>
+
+#include "tas2781-spi.h"
+
+#define OFFSET_ERROR_BIT BIT(31)
+
+#define ERROR_PRAM_CRCCHK 0x0000000
+#define ERROR_YRAM_CRCCHK 0x0000001
+#define PPC_DRIVER_CRCCHK 0x00000200
+
+#define TAS2781_SA_COEFF_SWAP_REG TASDEVICE_REG(0, 0x35, 0x2c)
+#define TAS2781_YRAM_BOOK1 140
+#define TAS2781_YRAM1_PAGE 42
+#define TAS2781_YRAM1_START_REG 88
+
+#define TAS2781_YRAM2_START_PAGE 43
+#define TAS2781_YRAM2_END_PAGE 49
+#define TAS2781_YRAM2_START_REG 8
+#define TAS2781_YRAM2_END_REG 127
+
+#define TAS2781_YRAM3_PAGE 50
+#define TAS2781_YRAM3_START_REG 8
+#define TAS2781_YRAM3_END_REG 27
+
+/* should not include B0_P53_R44-R47 */
+#define TAS2781_YRAM_BOOK2 0
+#define TAS2781_YRAM4_START_PAGE 50
+#define TAS2781_YRAM4_END_PAGE 60
+
+#define TAS2781_YRAM5_PAGE 61
+#define TAS2781_YRAM5_START_REG TAS2781_YRAM3_START_REG
+#define TAS2781_YRAM5_END_REG TAS2781_YRAM3_END_REG
+
+#define TASDEVICE_MAXPROGRAM_NUM_KERNEL 5
+#define TASDEVICE_MAXCONFIG_NUM_KERNEL_MULTIPLE_AMPS 64
+#define TASDEVICE_MAXCONFIG_NUM_KERNEL 10
+#define MAIN_ALL_DEVICES_1X 0x01
+#define MAIN_DEVICE_A_1X 0x02
+#define MAIN_DEVICE_B_1X 0x03
+#define MAIN_DEVICE_C_1X 0x04
+#define MAIN_DEVICE_D_1X 0x05
+#define COEFF_DEVICE_A_1X 0x12
+#define COEFF_DEVICE_B_1X 0x13
+#define COEFF_DEVICE_C_1X 0x14
+#define COEFF_DEVICE_D_1X 0x15
+#define PRE_DEVICE_A_1X 0x22
+#define PRE_DEVICE_B_1X 0x23
+#define PRE_DEVICE_C_1X 0x24
+#define PRE_DEVICE_D_1X 0x25
+#define PRE_SOFTWARE_RESET_DEVICE_A 0x41
+#define PRE_SOFTWARE_RESET_DEVICE_B 0x42
+#define PRE_SOFTWARE_RESET_DEVICE_C 0x43
+#define PRE_SOFTWARE_RESET_DEVICE_D 0x44
+#define POST_SOFTWARE_RESET_DEVICE_A 0x45
+#define POST_SOFTWARE_RESET_DEVICE_B 0x46
+#define POST_SOFTWARE_RESET_DEVICE_C 0x47
+#define POST_SOFTWARE_RESET_DEVICE_D 0x48
+
+struct tas_crc {
+ unsigned char offset;
+ unsigned char len;
+};
+
+struct blktyp_devidx_map {
+ unsigned char blktyp;
+ unsigned char dev_idx;
+};
+
+/* fixed m68k compiling issue: mapping table can save code field */
+static const struct blktyp_devidx_map ppc3_tas2781_mapping_table[] = {
+ { MAIN_ALL_DEVICES_1X, 0x80 },
+ { MAIN_DEVICE_A_1X, 0x81 },
+ { COEFF_DEVICE_A_1X, 0xC1 },
+ { PRE_DEVICE_A_1X, 0xC1 },
+ { PRE_SOFTWARE_RESET_DEVICE_A, 0xC1 },
+ { POST_SOFTWARE_RESET_DEVICE_A, 0xC1 },
+ { MAIN_DEVICE_B_1X, 0x82 },
+ { COEFF_DEVICE_B_1X, 0xC2 },
+ { PRE_DEVICE_B_1X, 0xC2 },
+ { PRE_SOFTWARE_RESET_DEVICE_B, 0xC2 },
+ { POST_SOFTWARE_RESET_DEVICE_B, 0xC2 },
+ { MAIN_DEVICE_C_1X, 0x83 },
+ { COEFF_DEVICE_C_1X, 0xC3 },
+ { PRE_DEVICE_C_1X, 0xC3 },
+ { PRE_SOFTWARE_RESET_DEVICE_C, 0xC3 },
+ { POST_SOFTWARE_RESET_DEVICE_C, 0xC3 },
+ { MAIN_DEVICE_D_1X, 0x84 },
+ { COEFF_DEVICE_D_1X, 0xC4 },
+ { PRE_DEVICE_D_1X, 0xC4 },
+ { PRE_SOFTWARE_RESET_DEVICE_D, 0xC4 },
+ { POST_SOFTWARE_RESET_DEVICE_D, 0xC4 },
+};
+
+static const struct blktyp_devidx_map ppc3_mapping_table[] = {
+ { MAIN_ALL_DEVICES_1X, 0x80 },
+ { MAIN_DEVICE_A_1X, 0x81 },
+ { COEFF_DEVICE_A_1X, 0xC1 },
+ { PRE_DEVICE_A_1X, 0xC1 },
+ { MAIN_DEVICE_B_1X, 0x82 },
+ { COEFF_DEVICE_B_1X, 0xC2 },
+ { PRE_DEVICE_B_1X, 0xC2 },
+ { MAIN_DEVICE_C_1X, 0x83 },
+ { COEFF_DEVICE_C_1X, 0xC3 },
+ { PRE_DEVICE_C_1X, 0xC3 },
+ { MAIN_DEVICE_D_1X, 0x84 },
+ { COEFF_DEVICE_D_1X, 0xC4 },
+ { PRE_DEVICE_D_1X, 0xC4 },
+};
+
+static const struct blktyp_devidx_map non_ppc3_mapping_table[] = {
+ { MAIN_ALL_DEVICES, 0x80 },
+ { MAIN_DEVICE_A, 0x81 },
+ { COEFF_DEVICE_A, 0xC1 },
+ { PRE_DEVICE_A, 0xC1 },
+ { MAIN_DEVICE_B, 0x82 },
+ { COEFF_DEVICE_B, 0xC2 },
+ { PRE_DEVICE_B, 0xC2 },
+ { MAIN_DEVICE_C, 0x83 },
+ { COEFF_DEVICE_C, 0xC3 },
+ { PRE_DEVICE_C, 0xC3 },
+ { MAIN_DEVICE_D, 0x84 },
+ { COEFF_DEVICE_D, 0xC4 },
+ { PRE_DEVICE_D, 0xC4 },
+};
+/*
+ * Device support different configurations for different scene,
+ * like voice, music, calibration, was write in regbin file.
+ * Will be stored into tas_priv after regbin was loaded.
+ */
+static struct tasdevice_config_info *tasdevice_add_config(
+ struct tasdevice_priv *tas_priv, unsigned char *config_data,
+ unsigned int config_size, int *status)
+{
+ struct tasdevice_config_info *cfg_info;
+ struct tasdev_blk_data **bk_da;
+ unsigned int config_offset = 0;
+ unsigned int i;
+
+ /*
+ * In most projects are many audio cases, such as music, handfree,
+ * receiver, games, audio-to-haptics, PMIC record, bypass mode,
+ * portrait, landscape, etc. Even in multiple audios, one or
+ * two of the chips will work for the special case, such as
+ * ultrasonic application. In order to support these variable-numbers
+ * of audio cases, flexible configs have been introduced in the
+ * DSP firmware.
+ */
+ cfg_info = kzalloc(sizeof(*cfg_info), GFP_KERNEL);
+ if (!cfg_info) {
+ *status = -ENOMEM;
+ return NULL;
+ }
+
+ if (tas_priv->rcabin.fw_hdr.binary_version_num >= 0x105) {
+ if ((config_offset + 64) > config_size) {
+ *status = -EINVAL;
+ dev_err(tas_priv->dev, "add conf: Out of boundary\n");
+ goto config_err;
+ }
+ config_offset += 64;
+ }
+
+ if ((config_offset + 4) > config_size) {
+ *status = -EINVAL;
+ dev_err(tas_priv->dev, "add config: Out of boundary\n");
+ goto config_err;
+ }
+
+ /*
+ * convert data[offset], data[offset + 1], data[offset + 2] and
+ * data[offset + 3] into host
+ */
+ cfg_info->nblocks = get_unaligned_be32(&config_data[config_offset]);
+ config_offset += 4;
+
+ /*
+ * Several kinds of dsp/algorithm firmwares can run on tas2781,
+ * the number and size of blk are not fixed and different among
+ * these firmwares.
+ */
+ bk_da = cfg_info->blk_data = kcalloc(cfg_info->nblocks,
+ sizeof(*bk_da), GFP_KERNEL);
+ if (!bk_da) {
+ *status = -ENOMEM;
+ goto config_err;
+ }
+ cfg_info->real_nblocks = 0;
+ for (i = 0; i < cfg_info->nblocks; i++) {
+ if (config_offset + 12 > config_size) {
+ *status = -EINVAL;
+ dev_err(tas_priv->dev,
+ "%s: Out of boundary: i = %d nblocks = %u!\n",
+ __func__, i, cfg_info->nblocks);
+ goto block_err;
+ }
+ bk_da[i] = kzalloc(sizeof(*bk_da[i]), GFP_KERNEL);
+ if (!bk_da[i]) {
+ *status = -ENOMEM;
+ goto block_err;
+ }
+
+ bk_da[i]->dev_idx = config_data[config_offset];
+ config_offset++;
+
+ bk_da[i]->block_type = config_data[config_offset];
+ config_offset++;
+
+ bk_da[i]->yram_checksum =
+ get_unaligned_be16(&config_data[config_offset]);
+ config_offset += 2;
+ bk_da[i]->block_size =
+ get_unaligned_be32(&config_data[config_offset]);
+ config_offset += 4;
+
+ bk_da[i]->n_subblks =
+ get_unaligned_be32(&config_data[config_offset]);
+
+ config_offset += 4;
+
+ if (config_offset + bk_da[i]->block_size > config_size) {
+ *status = -EINVAL;
+ dev_err(tas_priv->dev,
+ "%s: Out of boundary: i = %d blks = %u!\n",
+ __func__, i, cfg_info->nblocks);
+ goto block_err;
+ }
+ /* instead of kzalloc+memcpy */
+ bk_da[i]->regdata = kmemdup(&config_data[config_offset],
+ bk_da[i]->block_size, GFP_KERNEL);
+ if (!bk_da[i]->regdata) {
+ *status = -ENOMEM;
+ i++;
+ goto block_err;
+ }
+
+ config_offset += bk_da[i]->block_size;
+ cfg_info->real_nblocks += 1;
+ }
+
+ return cfg_info;
+block_err:
+ for (int j = 0; j < i; j++)
+ kfree(bk_da[j]);
+ kfree(bk_da);
+config_err:
+ kfree(cfg_info);
+ return NULL;
+}
+
+/* Regbin file parser function. */
+int tasdevice_spi_rca_parser(void *context, const struct firmware *fmw)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_config_info **cfg_info;
+ struct tasdevice_rca_hdr *fw_hdr;
+ struct tasdevice_rca *rca;
+ unsigned int total_config_sz = 0;
+ int offset = 0, ret = 0, i;
+ unsigned char *buf;
+
+ rca = &tas_priv->rcabin;
+ fw_hdr = &rca->fw_hdr;
+ if (!fmw || !fmw->data) {
+ dev_err(tas_priv->dev, "Failed to read %s\n",
+ tas_priv->rca_binaryname);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -EINVAL;
+ }
+ buf = (unsigned char *)fmw->data;
+ fw_hdr->img_sz = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ if (fw_hdr->img_sz != fmw->size) {
+ dev_err(tas_priv->dev,
+ "File size not match, %d %u", (int)fmw->size,
+ fw_hdr->img_sz);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -EINVAL;
+ }
+
+ fw_hdr->checksum = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ fw_hdr->binary_version_num = get_unaligned_be32(&buf[offset]);
+ if (fw_hdr->binary_version_num < 0x103) {
+ dev_err(tas_priv->dev, "File version 0x%04x is too low",
+ fw_hdr->binary_version_num);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -EINVAL;
+ }
+ offset += 4;
+ fw_hdr->drv_fw_version = get_unaligned_be32(&buf[offset]);
+ offset += 8;
+ fw_hdr->plat_type = buf[offset++];
+ fw_hdr->dev_family = buf[offset++];
+ fw_hdr->reserve = buf[offset++];
+ fw_hdr->ndev = buf[offset++];
+ if (offset + TASDEVICE_DEVICE_SUM > fw_hdr->img_sz) {
+ dev_err(tas_priv->dev, "rca_ready: Out of boundary!\n");
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -EINVAL;
+ }
+
+ for (i = 0; i < TASDEVICE_DEVICE_SUM; i++, offset++)
+ fw_hdr->devs[i] = buf[offset];
+
+ fw_hdr->nconfig = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+
+ for (i = 0; i < TASDEVICE_CONFIG_SUM; i++) {
+ fw_hdr->config_size[i] = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ total_config_sz += fw_hdr->config_size[i];
+ }
+
+ if (fw_hdr->img_sz - total_config_sz != (unsigned int)offset) {
+ dev_err(tas_priv->dev, "Bin file err %d - %d != %d!\n",
+ fw_hdr->img_sz, total_config_sz, (int)offset);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -EINVAL;
+ }
+
+ cfg_info = kcalloc(fw_hdr->nconfig, sizeof(*cfg_info), GFP_KERNEL);
+ if (!cfg_info) {
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return -ENOMEM;
+ }
+ rca->cfg_info = cfg_info;
+ rca->ncfgs = 0;
+ for (i = 0; i < (int)fw_hdr->nconfig; i++) {
+ rca->ncfgs += 1;
+ cfg_info[i] = tasdevice_add_config(tas_priv, &buf[offset],
+ fw_hdr->config_size[i], &ret);
+ if (ret) {
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ return ret;
+ }
+ offset += (int)fw_hdr->config_size[i];
+ }
+
+ return ret;
+}
+
+/* fixed m68k compiling issue: mapping table can save code field */
+static unsigned char map_dev_idx(struct tasdevice_fw *tas_fmw,
+ struct tasdev_blk *block)
+{
+ struct blktyp_devidx_map *p =
+ (struct blktyp_devidx_map *)non_ppc3_mapping_table;
+ struct tasdevice_dspfw_hdr *fw_hdr = &tas_fmw->fw_hdr;
+ struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &fw_hdr->fixed_hdr;
+ int i, n = ARRAY_SIZE(non_ppc3_mapping_table);
+ unsigned char dev_idx = 0;
+
+ if (fw_fixed_hdr->ppcver >= PPC3_VERSION_TAS2781) {
+ p = (struct blktyp_devidx_map *)ppc3_tas2781_mapping_table;
+ n = ARRAY_SIZE(ppc3_tas2781_mapping_table);
+ } else if (fw_fixed_hdr->ppcver >= PPC3_VERSION) {
+ p = (struct blktyp_devidx_map *)ppc3_mapping_table;
+ n = ARRAY_SIZE(ppc3_mapping_table);
+ }
+
+ for (i = 0; i < n; i++) {
+ if (block->type == p[i].blktyp) {
+ dev_idx = p[i].dev_idx;
+ break;
+ }
+ }
+
+ return dev_idx;
+}
+
+/* Block parser function. */
+static int fw_parse_block_data_kernel(struct tasdevice_fw *tas_fmw,
+ struct tasdev_blk *block, const struct firmware *fmw, int offset)
+{
+ const unsigned char *data = fmw->data;
+
+ if (offset + 16 > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+
+ /*
+ * Convert data[offset], data[offset + 1], data[offset + 2] and
+ * data[offset + 3] into host.
+ */
+ block->type = get_unaligned_be32(&data[offset]);
+ offset += 4;
+
+ block->is_pchksum_present = data[offset++];
+ block->pchksum = data[offset++];
+ block->is_ychksum_present = data[offset++];
+ block->ychksum = data[offset++];
+ block->blk_size = get_unaligned_be32(&data[offset]);
+ offset += 4;
+ block->nr_subblocks = get_unaligned_be32(&data[offset]);
+ offset += 4;
+
+ /*
+ * Fixed m68k compiling issue:
+ * 1. mapping table can save code field.
+ * 2. storing the dev_idx as a member of block can reduce unnecessary
+ * time and system resource comsumption of dev_idx mapping every
+ * time the block data writing to the dsp.
+ */
+ block->dev_idx = map_dev_idx(tas_fmw, block);
+
+ if (offset + block->blk_size > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: nSublocks error\n", __func__);
+ return -EINVAL;
+ }
+ /* instead of kzalloc+memcpy */
+ block->data = kmemdup(&data[offset], block->blk_size, GFP_KERNEL);
+ if (!block->data)
+ return -ENOMEM;
+
+ offset += block->blk_size;
+
+ return offset;
+}
+
+/* Data of block parser function. */
+static int fw_parse_data_kernel(struct tasdevice_fw *tas_fmw,
+ struct tasdevice_data *img_data, const struct firmware *fmw,
+ int offset)
+{
+ const unsigned char *data = fmw->data;
+ struct tasdev_blk *blk;
+ unsigned int i;
+
+ if (offset + 4 > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+ img_data->nr_blk = get_unaligned_be32(&data[offset]);
+ offset += 4;
+
+ img_data->dev_blks = kcalloc(img_data->nr_blk,
+ sizeof(struct tasdev_blk), GFP_KERNEL);
+ if (!img_data->dev_blks)
+ return -ENOMEM;
+
+ for (i = 0; i < img_data->nr_blk; i++) {
+ blk = &img_data->dev_blks[i];
+ offset = fw_parse_block_data_kernel(
+ tas_fmw, blk, fmw, offset);
+ if (offset < 0) {
+ kfree(img_data->dev_blks);
+ return -EINVAL;
+ }
+ }
+
+ return offset;
+}
+
+/* Data of DSP program parser function. */
+static int fw_parse_program_data_kernel(
+ struct tasdevice_priv *tas_priv, struct tasdevice_fw *tas_fmw,
+ const struct firmware *fmw, int offset)
+{
+ struct tasdevice_prog *program;
+ unsigned int i;
+
+ for (i = 0; i < tas_fmw->nr_programs; i++) {
+ program = &tas_fmw->programs[i];
+ if (offset + 72 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: mpName error\n", __func__);
+ return -EINVAL;
+ }
+ /* skip 72 unused byts */
+ offset += 72;
+
+ offset = fw_parse_data_kernel(tas_fmw, &program->dev_data,
+ fmw, offset);
+ if (offset < 0)
+ break;
+ }
+
+ return offset;
+}
+
+/* Data of DSP configurations parser function. */
+static int fw_parse_configuration_data_kernel(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset)
+{
+ const unsigned char *data = fmw->data;
+ struct tasdevice_config *config;
+ unsigned int i;
+
+ for (i = 0; i < tas_fmw->nr_configurations; i++) {
+ config = &tas_fmw->configs[i];
+ if (offset + 80 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: mpName error\n", __func__);
+ return -EINVAL;
+ }
+ memcpy(config->name, &data[offset], 64);
+ /* skip extra 16 bytes */
+ offset += 80;
+
+ offset = fw_parse_data_kernel(tas_fmw, &config->dev_data,
+ fmw, offset);
+ if (offset < 0)
+ break;
+ }
+
+ return offset;
+}
+
+/* DSP firmware file header parser function for early PPC3 firmware binary. */
+static int fw_parse_variable_header_kernel(struct tasdevice_priv *tas_priv,
+ const struct firmware *fmw, int offset)
+{
+ struct tasdevice_fw *tas_fmw = tas_priv->fmw;
+ struct tasdevice_dspfw_hdr *fw_hdr = &tas_fmw->fw_hdr;
+ struct tasdevice_config *config;
+ struct tasdevice_prog *program;
+ const unsigned char *buf = fmw->data;
+ unsigned short max_confs;
+ unsigned int i;
+
+ if (offset + 12 + 4 * TASDEVICE_MAXPROGRAM_NUM_KERNEL > fmw->size) {
+ dev_err(tas_priv->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+ fw_hdr->device_family = get_unaligned_be16(&buf[offset]);
+ if (fw_hdr->device_family != 0) {
+ dev_err(tas_priv->dev, "%s:not TAS device\n", __func__);
+ return -EINVAL;
+ }
+ offset += 2;
+ fw_hdr->device = get_unaligned_be16(&buf[offset]);
+ if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE ||
+ fw_hdr->device == 6) {
+ dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device);
+ return -EINVAL;
+ }
+ offset += 2;
+
+ tas_fmw->nr_programs = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+
+ if (tas_fmw->nr_programs == 0 ||
+ tas_fmw->nr_programs > TASDEVICE_MAXPROGRAM_NUM_KERNEL) {
+ dev_err(tas_priv->dev, "mnPrograms is invalid\n");
+ return -EINVAL;
+ }
+
+ tas_fmw->programs = kcalloc(tas_fmw->nr_programs,
+ sizeof(*tas_fmw->programs), GFP_KERNEL);
+ if (!tas_fmw->programs)
+ return -ENOMEM;
+
+ for (i = 0; i < tas_fmw->nr_programs; i++) {
+ program = &tas_fmw->programs[i];
+ program->prog_size = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ }
+
+ /* Skip the unused prog_size */
+ offset += 4 * (TASDEVICE_MAXPROGRAM_NUM_KERNEL - tas_fmw->nr_programs);
+
+ tas_fmw->nr_configurations = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+
+ /*
+ * The max number of config in firmware greater than 4 pieces of
+ * tas2781s is different from the one lower than 4 pieces of
+ * tas2781s.
+ */
+ max_confs = TASDEVICE_MAXCONFIG_NUM_KERNEL;
+ if (tas_fmw->nr_configurations == 0 ||
+ tas_fmw->nr_configurations > max_confs) {
+ dev_err(tas_priv->dev, "%s: Conf is invalid\n", __func__);
+ kfree(tas_fmw->programs);
+ return -EINVAL;
+ }
+
+ if (offset + 4 * max_confs > fmw->size) {
+ dev_err(tas_priv->dev, "%s: mpConfigurations err\n", __func__);
+ kfree(tas_fmw->programs);
+ return -EINVAL;
+ }
+
+ tas_fmw->configs = kcalloc(tas_fmw->nr_configurations,
+ sizeof(*tas_fmw->configs), GFP_KERNEL);
+ if (!tas_fmw->configs) {
+ kfree(tas_fmw->programs);
+ return -ENOMEM;
+ }
+
+ for (i = 0; i < tas_fmw->nr_programs; i++) {
+ config = &tas_fmw->configs[i];
+ config->cfg_size = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ }
+
+ /* Skip the unused configs */
+ offset += 4 * (max_confs - tas_fmw->nr_programs);
+
+ return offset;
+}
+
+/*
+ * In sub-block data, have three type sub-block:
+ * 1. Single byte write.
+ * 2. Multi-byte write.
+ * 3. Delay.
+ * 4. Bits update.
+ * This function perform single byte write to device.
+ */
+static int tasdevice_single_byte_wr(void *context, unsigned char *data,
+ int sublocksize)
+{
+ struct tasdevice_priv *tas_priv = context;
+ unsigned short len = get_unaligned_be16(&data[2]);
+ int i, subblk_offset, rc;
+
+ subblk_offset = 4;
+ if (subblk_offset + 4 * len > sublocksize) {
+ dev_err(tas_priv->dev, "process_block: Out of boundary\n");
+ return 0;
+ }
+
+ for (i = 0; i < len; i++) {
+ rc = tasdevice_spi_dev_write(tas_priv,
+ TASDEVICE_REG(data[subblk_offset],
+ data[subblk_offset + 1], data[subblk_offset + 2]),
+ data[subblk_offset + 3]);
+ if (rc < 0) {
+ dev_err(tas_priv->dev,
+ "process_block: single write error\n");
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ subblk_offset += 4;
+ }
+
+ return subblk_offset;
+}
+/*
+ * In sub-block data, have three type sub-block:
+ * 1. Single byte write.
+ * 2. Multi-byte write.
+ * 3. Delay.
+ * 4. Bits update.
+ * This function perform multi-write to device.
+ */
+static int tasdevice_burst_wr(void *context, unsigned char *data,
+ int sublocksize)
+{
+ struct tasdevice_priv *tas_priv = context;
+ unsigned short len = get_unaligned_be16(&data[2]);
+ int subblk_offset, rc;
+
+ subblk_offset = 4;
+ if (subblk_offset + 4 + len > sublocksize) {
+ dev_err(tas_priv->dev, "%s: BST Out of boundary\n", __func__);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ if (len % 4) {
+ dev_err(tas_priv->dev, "%s:Bst-len(%u)not div by 4\n",
+ __func__, len);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+
+ rc = tasdevice_spi_dev_bulk_write(tas_priv,
+ TASDEVICE_REG(data[subblk_offset], data[subblk_offset + 1],
+ data[subblk_offset + 2]), &data[subblk_offset + 4], len);
+ if (rc < 0) {
+ dev_err(tas_priv->dev, "%s: bulk_write error = %d\n",
+ __func__, rc);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ subblk_offset += (len + 4);
+
+ return subblk_offset;
+}
+/* Just delay for ms.*/
+static int tasdevice_delay(void *context, unsigned char *data,
+ int sublocksize)
+{
+ struct tasdevice_priv *tas_priv = context;
+ unsigned int sleep_time, subblk_offset = 2;
+
+ if (subblk_offset + 2 > sublocksize) {
+ dev_err(tas_priv->dev, "%s: delay Out of boundary\n",
+ __func__);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ sleep_time = get_unaligned_be16(&data[2]) * 1000;
+ fsleep(sleep_time);
+ subblk_offset += 2;
+
+ return subblk_offset;
+}
+/*
+ * In sub-block data, have three type sub-block:
+ * 1. Single byte write.
+ * 2. Multi-byte write.
+ * 3. Delay.
+ * 4. Bits update.
+ * This function perform bits update.
+ */
+static int tasdevice_field_wr(void *context, unsigned char *data,
+ int sublocksize)
+{
+ struct tasdevice_priv *tas_priv = context;
+ int rc, subblk_offset = 2;
+
+ if (subblk_offset + 6 > sublocksize) {
+ dev_err(tas_priv->dev, "%s: bit write Out of boundary\n",
+ __func__);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ rc = tasdevice_spi_dev_update_bits(tas_priv,
+ TASDEVICE_REG(data[subblk_offset + 2],
+ data[subblk_offset + 3],
+ data[subblk_offset + 4]),
+ data[subblk_offset + 1], data[subblk_offset + 5]);
+ if (rc < 0) {
+ dev_err(tas_priv->dev, "%s: update_bits error = %d\n",
+ __func__, rc);
+ subblk_offset |= OFFSET_ERROR_BIT;
+ }
+ subblk_offset += 6;
+
+ return subblk_offset;
+}
+/* Data block process function. */
+static int tasdevice_process_block(void *context, unsigned char *data,
+ unsigned char dev_idx, int sublocksize)
+{
+ struct tasdevice_priv *tas_priv = context;
+ int blktyp = dev_idx & 0xC0, subblk_offset;
+ unsigned char subblk_typ = data[1];
+
+ if (tas_priv->is_loading == false)
+ return sublocksize;
+
+ switch (subblk_typ) {
+ case TASDEVICE_CMD_SING_W:
+ subblk_offset = tasdevice_single_byte_wr(tas_priv, data,
+ sublocksize);
+ break;
+ case TASDEVICE_CMD_BURST:
+ subblk_offset = tasdevice_burst_wr(tas_priv, data,
+ sublocksize);
+ break;
+ case TASDEVICE_CMD_DELAY:
+ subblk_offset = tasdevice_delay(tas_priv, data, sublocksize);
+ break;
+ case TASDEVICE_CMD_FIELD_W:
+ subblk_offset = tasdevice_field_wr(tas_priv, data,
+ sublocksize);
+ break;
+ default:
+ subblk_offset = 2;
+ break;
+ }
+ if (((subblk_offset & OFFSET_ERROR_BIT) != 0) && blktyp != 0) {
+ if (blktyp == 0x80) {
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+ } else
+ tas_priv->cur_conf = -1;
+ }
+ subblk_offset &= ~OFFSET_ERROR_BIT;
+
+ return subblk_offset;
+}
+/*
+ * Device support different configurations for different scene,
+ * this function was used for choose different config.
+ */
+void tasdevice_spi_select_cfg_blk(void *pContext, int conf_no,
+ unsigned char block_type)
+{
+ struct tasdevice_priv *tas_priv = pContext;
+ struct tasdevice_rca *rca = &tas_priv->rcabin;
+ struct tasdevice_config_info **cfg_info = rca->cfg_info;
+ struct tasdev_blk_data **blk_data;
+ unsigned int j, k;
+
+ if (conf_no >= rca->ncfgs || conf_no < 0 || !cfg_info) {
+ dev_err(tas_priv->dev, "conf_no should be not more than %u\n",
+ rca->ncfgs);
+ return;
+ }
+ blk_data = cfg_info[conf_no]->blk_data;
+
+ for (j = 0; j < cfg_info[conf_no]->real_nblocks; j++) {
+ unsigned int length = 0, rc = 0;
+
+ if (block_type > 5 || block_type < 2) {
+ dev_err(tas_priv->dev,
+ "block_type should be in range from 2 to 5\n");
+ break;
+ }
+ if (block_type != blk_data[j]->block_type)
+ continue;
+
+ for (k = 0; k < blk_data[j]->n_subblks; k++) {
+ tas_priv->is_loading = true;
+
+ rc = tasdevice_process_block(tas_priv,
+ blk_data[j]->regdata + length,
+ blk_data[j]->dev_idx,
+ blk_data[j]->block_size - length);
+ length += rc;
+ if (blk_data[j]->block_size < length) {
+ dev_err(tas_priv->dev,
+ "%s: %u %u out of boundary\n",
+ __func__, length,
+ blk_data[j]->block_size);
+ break;
+ }
+ }
+ if (length != blk_data[j]->block_size)
+ dev_err(tas_priv->dev, "%s: %u %u size is not same\n",
+ __func__, length, blk_data[j]->block_size);
+ }
+}
+/* Block process function. */
+static int tasdevice_load_block_kernel(
+ struct tasdevice_priv *tasdevice, struct tasdev_blk *block)
+{
+ const unsigned int blk_size = block->blk_size;
+ unsigned char *data = block->data;
+ unsigned int i, length;
+
+ for (i = 0, length = 0; i < block->nr_subblocks; i++) {
+ int rc = tasdevice_process_block(tasdevice, data + length,
+ block->dev_idx, blk_size - length);
+ if (rc < 0) {
+ dev_err(tasdevice->dev,
+ "%s: %u %u sublock write error\n",
+ __func__, length, blk_size);
+ break;
+ }
+ length += rc;
+ if (blk_size < length) {
+ dev_err(tasdevice->dev, "%s: %u %u out of boundary\n",
+ __func__, length, blk_size);
+ break;
+ }
+ }
+
+ return 0;
+}
+/* DSP firmware file header parser function. */
+static int fw_parse_variable_hdr(struct tasdevice_priv *tas_priv,
+ struct tasdevice_dspfw_hdr *fw_hdr,
+ const struct firmware *fmw, int offset)
+{
+ const unsigned char *buf = fmw->data;
+ int len = strlen((char *)&buf[offset]);
+
+ len++;
+
+ if (offset + len + 8 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+
+ offset += len;
+
+ fw_hdr->device_family = get_unaligned_be32(&buf[offset]);
+ if (fw_hdr->device_family != 0) {
+ dev_err(tas_priv->dev, "%s: not TAS device\n", __func__);
+ return -EINVAL;
+ }
+ offset += 4;
+
+ fw_hdr->device = get_unaligned_be32(&buf[offset]);
+ if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE ||
+ fw_hdr->device == 6) {
+ dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device);
+ return -EINVAL;
+ }
+ offset += 4;
+ fw_hdr->ndev = 1;
+
+ return offset;
+}
+
+/* DSP firmware file header parser function for size variabled header. */
+static int fw_parse_variable_header_git(struct tasdevice_priv
+ *tas_priv, const struct firmware *fmw, int offset)
+{
+ struct tasdevice_fw *tas_fmw = tas_priv->fmw;
+ struct tasdevice_dspfw_hdr *fw_hdr = &tas_fmw->fw_hdr;
+
+ offset = fw_parse_variable_hdr(tas_priv, fw_hdr, fmw, offset);
+
+ return offset;
+}
+
+/* DSP firmware file block parser function. */
+static int fw_parse_block_data(struct tasdevice_fw *tas_fmw,
+ struct tasdev_blk *block, const struct firmware *fmw, int offset)
+{
+ unsigned char *data = (unsigned char *)fmw->data;
+ int n;
+
+ if (offset + 8 > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: Type error\n", __func__);
+ return -EINVAL;
+ }
+ block->type = get_unaligned_be32(&data[offset]);
+ offset += 4;
+
+ if (tas_fmw->fw_hdr.fixed_hdr.drv_ver >= PPC_DRIVER_CRCCHK) {
+ if (offset + 8 > fmw->size) {
+ dev_err(tas_fmw->dev, "PChkSumPresent error\n");
+ return -EINVAL;
+ }
+ block->is_pchksum_present = data[offset];
+ offset++;
+
+ block->pchksum = data[offset];
+ offset++;
+
+ block->is_ychksum_present = data[offset];
+ offset++;
+
+ block->ychksum = data[offset];
+ offset++;
+ } else {
+ block->is_pchksum_present = 0;
+ block->is_ychksum_present = 0;
+ }
+
+ block->nr_cmds = get_unaligned_be32(&data[offset]);
+ offset += 4;
+
+ n = block->nr_cmds * 4;
+ if (offset + n > fmw->size) {
+ dev_err(tas_fmw->dev,
+ "%s: File Size(%lu) error offset = %d n = %d\n",
+ __func__, (unsigned long)fmw->size, offset, n);
+ return -EINVAL;
+ }
+ /* instead of kzalloc+memcpy */
+ block->data = kmemdup(&data[offset], n, GFP_KERNEL);
+ if (!block->data)
+ return -ENOMEM;
+
+ offset += n;
+
+ return offset;
+}
+
+/*
+ * When parsing error occurs, all the memory resource will be released
+ * in the end of tasdevice_rca_ready.
+ */
+static int fw_parse_data(struct tasdevice_fw *tas_fmw,
+ struct tasdevice_data *img_data, const struct firmware *fmw,
+ int offset)
+{
+ const unsigned char *data = (unsigned char *)fmw->data;
+ struct tasdev_blk *blk;
+ unsigned int i, n;
+
+ if (offset + 64 > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: Name error\n", __func__);
+ return -EINVAL;
+ }
+ memcpy(img_data->name, &data[offset], 64);
+ offset += 64;
+
+ n = strlen((char *)&data[offset]);
+ n++;
+ if (offset + n + 2 > fmw->size) {
+ dev_err(tas_fmw->dev, "%s: Description error\n", __func__);
+ return -EINVAL;
+ }
+ offset += n;
+ img_data->nr_blk = get_unaligned_be16(&data[offset]);
+ offset += 2;
+
+ img_data->dev_blks = kcalloc(img_data->nr_blk,
+ sizeof(*img_data->dev_blks), GFP_KERNEL);
+ if (!img_data->dev_blks)
+ return -ENOMEM;
+
+ for (i = 0; i < img_data->nr_blk; i++) {
+ blk = &img_data->dev_blks[i];
+ offset = fw_parse_block_data(tas_fmw, blk, fmw, offset);
+ if (offset < 0)
+ return -EINVAL;
+ }
+
+ return offset;
+}
+
+/*
+ * When parsing error occurs, all the memory resource will be released
+ * in the end of tasdevice_rca_ready.
+ */
+static int fw_parse_program_data(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset)
+{
+ unsigned char *buf = (unsigned char *)fmw->data;
+ struct tasdevice_prog *program;
+ int i;
+
+ if (offset + 2 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+ tas_fmw->nr_programs = get_unaligned_be16(&buf[offset]);
+ offset += 2;
+
+ if (tas_fmw->nr_programs == 0) {
+ /* Not error in calibration Data file, return directly */
+ dev_info(tas_priv->dev, "%s: No Programs data, maybe calbin\n",
+ __func__);
+ return offset;
+ }
+
+ tas_fmw->programs =
+ kcalloc(tas_fmw->nr_programs, sizeof(*tas_fmw->programs),
+ GFP_KERNEL);
+ if (!tas_fmw->programs)
+ return -ENOMEM;
+
+ for (i = 0; i < tas_fmw->nr_programs; i++) {
+ int n = 0;
+
+ program = &tas_fmw->programs[i];
+ if (offset + 64 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: mpName error\n", __func__);
+ return -EINVAL;
+ }
+ offset += 64;
+
+ n = strlen((char *)&buf[offset]);
+ /* skip '\0' and 5 unused bytes */
+ n += 6;
+ if (offset + n > fmw->size) {
+ dev_err(tas_priv->dev, "Description err\n");
+ return -EINVAL;
+ }
+
+ offset += n;
+
+ offset = fw_parse_data(tas_fmw, &program->dev_data, fmw,
+ offset);
+ if (offset < 0)
+ return offset;
+ }
+
+ return offset;
+}
+
+/*
+ * When parsing error occurs, all the memory resource will be released
+ * in the end of tasdevice_rca_ready.
+ */
+static int fw_parse_configuration_data(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset)
+{
+ unsigned char *data = (unsigned char *)fmw->data;
+ struct tasdevice_config *config;
+ unsigned int i, n;
+
+ if (offset + 2 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: File Size error\n", __func__);
+ return -EINVAL;
+ }
+ tas_fmw->nr_configurations = get_unaligned_be16(&data[offset]);
+ offset += 2;
+
+ if (tas_fmw->nr_configurations == 0) {
+ dev_err(tas_priv->dev, "%s: Conf is zero\n", __func__);
+ /* Not error for calibration Data file, return directly */
+ return offset;
+ }
+ tas_fmw->configs = kcalloc(tas_fmw->nr_configurations,
+ sizeof(*tas_fmw->configs), GFP_KERNEL);
+ if (!tas_fmw->configs)
+ return -ENOMEM;
+ for (i = 0; i < tas_fmw->nr_configurations; i++) {
+ config = &tas_fmw->configs[i];
+ if (offset + 64 > fmw->size) {
+ dev_err(tas_priv->dev, "File Size err\n");
+ return -EINVAL;
+ }
+ memcpy(config->name, &data[offset], 64);
+ offset += 64;
+
+ n = strlen((char *)&data[offset]);
+ n += 15;
+ if (offset + n > fmw->size) {
+ dev_err(tas_priv->dev, "Description err\n");
+ return -EINVAL;
+ }
+ offset += n;
+ offset = fw_parse_data(tas_fmw, &config->dev_data,
+ fmw, offset);
+ if (offset < 0)
+ break;
+ }
+
+ return offset;
+}
+
+/* yram5 page check. */
+static bool check_inpage_yram_rg(struct tas_crc *cd,
+ unsigned char reg, unsigned char len)
+{
+ bool in = false;
+
+ if (reg <= TAS2781_YRAM5_END_REG &&
+ reg >= TAS2781_YRAM5_START_REG) {
+ if (reg + len > TAS2781_YRAM5_END_REG)
+ cd->len = TAS2781_YRAM5_END_REG - reg + 1;
+ else
+ cd->len = len;
+ cd->offset = reg;
+ in = true;
+ } else if (reg < TAS2781_YRAM5_START_REG) {
+ if (reg + len > TAS2781_YRAM5_START_REG) {
+ cd->offset = TAS2781_YRAM5_START_REG;
+ cd->len = len - TAS2781_YRAM5_START_REG + reg;
+ in = true;
+ }
+ }
+
+ return in;
+}
+
+/* DSP firmware yram block check. */
+static bool check_inpage_yram_bk1(struct tas_crc *cd,
+ unsigned char page, unsigned char reg, unsigned char len)
+{
+ bool in = false;
+
+ if (page == TAS2781_YRAM1_PAGE) {
+ if (reg >= TAS2781_YRAM1_START_REG) {
+ cd->offset = reg;
+ cd->len = len;
+ in = true;
+ } else if (reg + len > TAS2781_YRAM1_START_REG) {
+ cd->offset = TAS2781_YRAM1_START_REG;
+ cd->len = len - TAS2781_YRAM1_START_REG + reg;
+ in = true;
+ }
+ } else if (page == TAS2781_YRAM3_PAGE) {
+ in = check_inpage_yram_rg(cd, reg, len);
+ }
+
+ return in;
+}
+
+/*
+ * Return Code:
+ * true -- the registers are in the inpage yram
+ * false -- the registers are NOT in the inpage yram
+ */
+static bool check_inpage_yram(struct tas_crc *cd, unsigned char book,
+ unsigned char page, unsigned char reg, unsigned char len)
+{
+ bool in = false;
+
+ if (book == TAS2781_YRAM_BOOK1)
+ in = check_inpage_yram_bk1(cd, page, reg, len);
+ else if (book == TAS2781_YRAM_BOOK2 && page == TAS2781_YRAM5_PAGE)
+ in = check_inpage_yram_rg(cd, reg, len);
+
+ return in;
+}
+/* yram4 page check. */
+static bool check_inblock_yram_bk(struct tas_crc *cd,
+ unsigned char page, unsigned char reg, unsigned char len)
+{
+ bool in = false;
+
+ if ((page >= TAS2781_YRAM4_START_PAGE &&
+ page <= TAS2781_YRAM4_END_PAGE) ||
+ (page >= TAS2781_YRAM2_START_PAGE &&
+ page <= TAS2781_YRAM2_END_PAGE)) {
+ if (reg <= TAS2781_YRAM2_END_REG &&
+ reg >= TAS2781_YRAM2_START_REG) {
+ cd->offset = reg;
+ cd->len = len;
+ in = true;
+ } else if (reg < TAS2781_YRAM2_START_REG) {
+ if (reg + len - 1 >= TAS2781_YRAM2_START_REG) {
+ cd->offset = TAS2781_YRAM2_START_REG;
+ cd->len = reg + len - TAS2781_YRAM2_START_REG;
+ in = true;
+ }
+ }
+ }
+
+ return in;
+}
+
+/*
+ * Return Code:
+ * true -- the registers are in the inblock yram
+ * false -- the registers are NOT in the inblock yram
+ */
+static bool check_inblock_yram(struct tas_crc *cd, unsigned char book,
+ unsigned char page, unsigned char reg, unsigned char len)
+{
+ bool in = false;
+
+ if (book == TAS2781_YRAM_BOOK1 || book == TAS2781_YRAM_BOOK2)
+ in = check_inblock_yram_bk(cd, page, reg, len);
+
+ return in;
+}
+/* yram page check. */
+static bool check_yram(struct tas_crc *cd, unsigned char book,
+ unsigned char page, unsigned char reg, unsigned char len)
+{
+ bool in;
+
+ in = check_inpage_yram(cd, book, page, reg, len);
+ if (!in)
+ in = check_inblock_yram(cd, book, page, reg, len);
+
+ return in;
+}
+
+/* Checksum for data block. */
+static int tasdev_multibytes_chksum(struct tasdevice_priv *tasdevice,
+ unsigned char book, unsigned char page,
+ unsigned char reg, unsigned int len)
+{
+ struct tas_crc crc_data;
+ unsigned char crc_chksum = 0;
+ unsigned char nBuf1[128];
+ int ret = 0, i;
+ bool in;
+
+ if ((reg + len - 1) > 127) {
+ ret = -EINVAL;
+ dev_err(tasdevice->dev, "firmware error\n");
+ goto end;
+ }
+
+ if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (reg == TASDEVICE_REG_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (len == 4)) {
+ /* DSP swap command, pass */
+ ret = 0;
+ goto end;
+ }
+
+ in = check_yram(&crc_data, book, page, reg, len);
+ if (!in)
+ goto end;
+
+ if (len == 1) {
+ dev_err(tasdevice->dev, "firmware error\n");
+ ret = -EINVAL;
+ goto end;
+ }
+
+ ret = tasdevice_spi_dev_bulk_read(tasdevice,
+ TASDEVICE_REG(book, page, crc_data.offset),
+ nBuf1, crc_data.len);
+ if (ret < 0)
+ goto end;
+
+ for (i = 0; i < crc_data.len; i++) {
+ if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ ((i + crc_data.offset) >=
+ TASDEVICE_REG_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ ((i + crc_data.offset) <=
+ (TASDEVICE_REG_ID(TAS2781_SA_COEFF_SWAP_REG) + 4)))
+ /* DSP swap command, bypass */
+ continue;
+ else
+ crc_chksum += crc8(tasdevice->crc8_lkp_tbl, &nBuf1[i],
+ 1, 0);
+ }
+
+ ret = crc_chksum;
+
+end:
+ return ret;
+}
+
+/* Checksum for single register. */
+static int do_singlereg_checksum(struct tasdevice_priv *tasdevice,
+ unsigned char book, unsigned char page,
+ unsigned char reg, unsigned char val)
+{
+ struct tas_crc crc_data;
+ unsigned int nData1;
+ int ret = 0;
+ bool in;
+
+ /* DSP swap command, pass */
+ if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (reg >= TASDEVICE_REG_ID(TAS2781_SA_COEFF_SWAP_REG)) &&
+ (reg <= (TASDEVICE_REG_ID(TAS2781_SA_COEFF_SWAP_REG) + 4)))
+ return 0;
+
+ in = check_yram(&crc_data, book, page, reg, 1);
+ if (!in)
+ return 0;
+ ret = tasdevice_spi_dev_read(tasdevice,
+ TASDEVICE_REG(book, page, reg), &nData1);
+ if (ret < 0)
+ return ret;
+
+ if (nData1 != val) {
+ dev_err(tasdevice->dev,
+ "B[0x%x]P[0x%x]R[0x%x] W[0x%x], R[0x%x]\n",
+ book, page, reg, val, nData1);
+ tasdevice->err_code |= ERROR_YRAM_CRCCHK;
+ return -EAGAIN;
+ }
+
+ ret = crc8(tasdevice->crc8_lkp_tbl, &val, 1, 0);
+
+ return ret;
+}
+
+/* Block type check. */
+static void set_err_prg_cfg(unsigned int type, struct tasdevice_priv *p)
+{
+ if ((type == MAIN_ALL_DEVICES) || (type == MAIN_DEVICE_A) ||
+ (type == MAIN_DEVICE_B) || (type == MAIN_DEVICE_C) ||
+ (type == MAIN_DEVICE_D))
+ p->cur_prog = -1;
+ else
+ p->cur_conf = -1;
+}
+/* Checksum for data bytes. */
+static int tasdev_bytes_chksum(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block, unsigned char book,
+ unsigned char page, unsigned char reg, unsigned int len,
+ unsigned char val, unsigned char *crc_chksum)
+{
+ int ret;
+
+ if (len > 1)
+ ret = tasdev_multibytes_chksum(tas_priv, book, page, reg,
+ len);
+ else
+ ret = do_singlereg_checksum(tas_priv, book, page, reg, val);
+
+ if (ret > 0) {
+ *crc_chksum += ret;
+ goto end;
+ }
+
+ if (ret != -EAGAIN)
+ goto end;
+
+ block->nr_retry--;
+ if (block->nr_retry > 0)
+ goto end;
+
+ set_err_prg_cfg(block->type, tas_priv);
+
+end:
+ return ret;
+}
+/* Multi-data byte write. */
+static int tasdev_multibytes_wr(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block, unsigned char book,
+ unsigned char page, unsigned char reg, unsigned char *data,
+ unsigned int len, unsigned int *nr_cmds,
+ unsigned char *crc_chksum)
+{
+ int ret;
+
+ if (len > 1) {
+ ret = tasdevice_spi_dev_bulk_write(tas_priv,
+ TASDEVICE_REG(book, page, reg), data + 3, len);
+ if (ret < 0)
+ return ret;
+ if (block->is_ychksum_present)
+ ret = tasdev_bytes_chksum(tas_priv, block,
+ book, page, reg, len, 0, crc_chksum);
+ } else {
+ ret = tasdevice_spi_dev_write(tas_priv,
+ TASDEVICE_REG(book, page, reg), data[3]);
+ if (ret < 0)
+ return ret;
+ if (block->is_ychksum_present)
+ ret = tasdev_bytes_chksum(tas_priv, block, book,
+ page, reg, 1, data[3], crc_chksum);
+ }
+
+ if (!block->is_ychksum_present || ret >= 0) {
+ *nr_cmds += 1;
+ if (len >= 2)
+ *nr_cmds += ((len - 2) / 4) + 1;
+ }
+
+ return ret;
+}
+/* Checksum for block. */
+static int tasdev_block_chksum(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block)
+{
+ unsigned int nr_value;
+ int ret;
+
+ ret = tasdevice_spi_dev_read(tas_priv, TASDEVICE_CHECKSUM, &nr_value);
+ if (ret < 0) {
+ dev_err(tas_priv->dev, "%s: read error %d.\n", __func__, ret);
+ set_err_prg_cfg(block->type, tas_priv);
+ return ret;
+ }
+
+ if ((nr_value & 0xff) != block->pchksum) {
+ dev_err(tas_priv->dev, "%s: PChkSum err %d ", __func__, ret);
+ dev_err(tas_priv->dev, "PChkSum = 0x%x, Reg = 0x%x\n",
+ block->pchksum, (nr_value & 0xff));
+ tas_priv->err_code |= ERROR_PRAM_CRCCHK;
+ ret = -EAGAIN;
+ block->nr_retry--;
+
+ if (block->nr_retry <= 0)
+ set_err_prg_cfg(block->type, tas_priv);
+ } else {
+ tas_priv->err_code &= ~ERROR_PRAM_CRCCHK;
+ }
+
+ return ret;
+}
+/* Firmware block load function. */
+static int tasdev_load_blk(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block)
+{
+ unsigned int sleep_time, len, nr_cmds;
+ unsigned char offset, book, page, val;
+ unsigned char *data = block->data;
+ unsigned char crc_chksum = 0;
+ int ret = 0;
+
+ while (block->nr_retry > 0) {
+ if (block->is_pchksum_present) {
+ ret = tasdevice_spi_dev_write(tas_priv,
+ TASDEVICE_CHECKSUM, 0);
+ if (ret < 0)
+ break;
+ }
+
+ if (block->is_ychksum_present)
+ crc_chksum = 0;
+
+ nr_cmds = 0;
+
+ while (nr_cmds < block->nr_cmds) {
+ data = block->data + nr_cmds * 4;
+
+ book = data[0];
+ page = data[1];
+ offset = data[2];
+ val = data[3];
+
+ nr_cmds++;
+ /* Single byte write */
+ if (offset <= 0x7F) {
+ ret = tasdevice_spi_dev_write(tas_priv,
+ TASDEVICE_REG(book, page, offset),
+ val);
+ if (ret < 0)
+ break;
+ if (block->is_ychksum_present) {
+ ret = tasdev_bytes_chksum(tas_priv,
+ block, book, page, offset,
+ 1, val, &crc_chksum);
+ if (ret < 0)
+ break;
+ }
+ continue;
+ }
+ /* sleep command */
+ if (offset == 0x81) {
+ /* book -- data[0] page -- data[1] */
+ sleep_time = ((book << 8) + page)*1000;
+ fsleep(sleep_time);
+ continue;
+ }
+ /* Multiple bytes write */
+ if (offset == 0x85) {
+ data += 4;
+ len = (book << 8) + page;
+ book = data[0];
+ page = data[1];
+ offset = data[2];
+ ret = tasdev_multibytes_wr(tas_priv,
+ block, book, page, offset, data,
+ len, &nr_cmds, &crc_chksum);
+ if (ret < 0)
+ break;
+ }
+ }
+ if (ret == -EAGAIN) {
+ if (block->nr_retry > 0)
+ continue;
+ } else if (ret < 0) {
+ /* err in current device, skip it */
+ break;
+ }
+
+ if (block->is_pchksum_present) {
+ ret = tasdev_block_chksum(tas_priv, block);
+ if (ret == -EAGAIN) {
+ if (block->nr_retry > 0)
+ continue;
+ } else if (ret < 0) {
+ /* err in current device, skip it */
+ break;
+ }
+ }
+
+ if (block->is_ychksum_present) {
+ /* TBD, open it when FW ready */
+ dev_err(tas_priv->dev,
+ "Blk YChkSum: FW = 0x%x, YCRC = 0x%x\n",
+ block->ychksum, crc_chksum);
+
+ tas_priv->err_code &=
+ ~ERROR_YRAM_CRCCHK;
+ ret = 0;
+ }
+ /* skip current blk */
+ break;
+ }
+
+ return ret;
+}
+/* Firmware block load function. */
+static int tasdevice_load_block(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block)
+{
+ int ret = 0;
+
+ block->nr_retry = 6;
+ if (tas_priv->is_loading == false)
+ return 0;
+ ret = tasdev_load_blk(tas_priv, block);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "Blk (%d) load error\n", block->type);
+
+ return ret;
+}
+
+/*
+ * Select firmware binary parser & load callback functions by ppc3 version
+ * and firmware binary version.
+ */
+static int dspfw_default_callback(struct tasdevice_priv *tas_priv,
+ unsigned int drv_ver, unsigned int ppcver)
+{
+ int rc = 0;
+
+ if (drv_ver == 0x100) {
+ if (ppcver >= PPC3_VERSION) {
+ tas_priv->fw_parse_variable_header =
+ fw_parse_variable_header_kernel;
+ tas_priv->fw_parse_program_data =
+ fw_parse_program_data_kernel;
+ tas_priv->fw_parse_configuration_data =
+ fw_parse_configuration_data_kernel;
+ tas_priv->tasdevice_load_block =
+ tasdevice_load_block_kernel;
+ } else {
+ switch (ppcver) {
+ case 0x00:
+ tas_priv->fw_parse_variable_header =
+ fw_parse_variable_header_git;
+ tas_priv->fw_parse_program_data =
+ fw_parse_program_data;
+ tas_priv->fw_parse_configuration_data =
+ fw_parse_configuration_data;
+ tas_priv->tasdevice_load_block =
+ tasdevice_load_block;
+ break;
+ default:
+ dev_err(tas_priv->dev,
+ "%s: PPCVer must be 0x0 or 0x%02x",
+ __func__, PPC3_VERSION);
+ dev_err(tas_priv->dev, " Current:0x%02x\n",
+ ppcver);
+ rc = -EINVAL;
+ break;
+ }
+ }
+ } else {
+ dev_err(tas_priv->dev,
+ "DrvVer must be 0x0, 0x230 or above 0x230 ");
+ dev_err(tas_priv->dev, "current is 0x%02x\n", drv_ver);
+ rc = -EINVAL;
+ }
+
+ return rc;
+}
+/* Calibration block load function. */
+static int load_calib_data(struct tasdevice_priv *tas_priv,
+ struct tasdevice_data *dev_data)
+{
+ struct tasdev_blk *block;
+ unsigned int i;
+ int ret = 0;
+
+ for (i = 0; i < dev_data->nr_blk; i++) {
+ block = &dev_data->dev_blks[i];
+ ret = tasdevice_load_block(tas_priv, block);
+ if (ret < 0)
+ break;
+ }
+
+ return ret;
+}
+
+/* DSP firmware binary file header parser function. */
+static int fw_parse_header(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset)
+{
+ struct tasdevice_dspfw_hdr *fw_hdr = &tas_fmw->fw_hdr;
+ struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &fw_hdr->fixed_hdr;
+ static const unsigned char magic_number[] = {0x35, 0x35, 0x35, 0x32, };
+ const unsigned char *buf = (unsigned char *)fmw->data;
+
+ if (offset + 92 > fmw->size) {
+ dev_err(tas_priv->dev, "%s: File Size error\n", __func__);
+ offset = -EINVAL;
+ goto out;
+ }
+ if (memcmp(&buf[offset], magic_number, 4)) {
+ dev_err(tas_priv->dev, "%s: Magic num NOT match\n", __func__);
+ offset = -EINVAL;
+ goto out;
+ }
+ offset += 4;
+
+ /*
+ * Convert data[offset], data[offset + 1], data[offset + 2] and
+ * data[offset + 3] into host
+ */
+ fw_fixed_hdr->fwsize = get_unaligned_be32(&buf[offset]);
+ offset += 4;
+ if (fw_fixed_hdr->fwsize != fmw->size) {
+ dev_err(tas_priv->dev, "File size not match, %lu %u",
+ (unsigned long)fmw->size, fw_fixed_hdr->fwsize);
+ offset = -EINVAL;
+ goto out;
+ }
+ offset += 4;
+ fw_fixed_hdr->ppcver = get_unaligned_be32(&buf[offset]);
+ offset += 8;
+ fw_fixed_hdr->drv_ver = get_unaligned_be32(&buf[offset]);
+ offset += 72;
+
+out:
+ return offset;
+}
+
+/* DSP firmware binary file parser function. */
+static int tasdevice_dspfw_ready(const struct firmware *fmw, void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_fw_fixed_hdr *fw_fixed_hdr;
+ struct tasdevice_fw *tas_fmw;
+ int offset = 0, ret = 0;
+
+ if (!fmw || !fmw->data) {
+ dev_err(tas_priv->dev, "%s: Failed to read firmware %s\n",
+ __func__, tas_priv->coef_binaryname);
+ return -EINVAL;
+ }
+
+ tas_priv->fmw = kzalloc(sizeof(*tas_priv->fmw), GFP_KERNEL);
+ if (!tas_priv->fmw)
+ return -ENOMEM;
+ tas_fmw = tas_priv->fmw;
+ tas_fmw->dev = tas_priv->dev;
+ offset = fw_parse_header(tas_priv, tas_fmw, fmw, offset);
+
+ if (offset == -EINVAL)
+ return -EINVAL;
+
+ fw_fixed_hdr = &tas_fmw->fw_hdr.fixed_hdr;
+ /* Support different versions of firmware */
+ switch (fw_fixed_hdr->drv_ver) {
+ case 0x301:
+ case 0x302:
+ case 0x502:
+ case 0x503:
+ tas_priv->fw_parse_variable_header =
+ fw_parse_variable_header_kernel;
+ tas_priv->fw_parse_program_data =
+ fw_parse_program_data_kernel;
+ tas_priv->fw_parse_configuration_data =
+ fw_parse_configuration_data_kernel;
+ tas_priv->tasdevice_load_block =
+ tasdevice_load_block_kernel;
+ break;
+ case 0x202:
+ case 0x400:
+ tas_priv->fw_parse_variable_header =
+ fw_parse_variable_header_git;
+ tas_priv->fw_parse_program_data =
+ fw_parse_program_data;
+ tas_priv->fw_parse_configuration_data =
+ fw_parse_configuration_data;
+ tas_priv->tasdevice_load_block =
+ tasdevice_load_block;
+ break;
+ default:
+ ret = dspfw_default_callback(tas_priv,
+ fw_fixed_hdr->drv_ver, fw_fixed_hdr->ppcver);
+ if (ret)
+ return ret;
+ break;
+ }
+
+ offset = tas_priv->fw_parse_variable_header(tas_priv, fmw, offset);
+ if (offset < 0)
+ return offset;
+
+ offset = tas_priv->fw_parse_program_data(tas_priv, tas_fmw, fmw,
+ offset);
+ if (offset < 0)
+ return offset;
+
+ offset = tas_priv->fw_parse_configuration_data(tas_priv,
+ tas_fmw, fmw, offset);
+ if (offset < 0)
+ ret = offset;
+
+ return ret;
+}
+/* DSP firmware binary file parser function. */
+int tasdevice_spi_dsp_parser(void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+ const struct firmware *fw_entry;
+ int ret;
+
+ ret = request_firmware(&fw_entry, tas_priv->coef_binaryname,
+ tas_priv->dev);
+ if (ret) {
+ dev_err(tas_priv->dev, "%s: load %s error\n", __func__,
+ tas_priv->coef_binaryname);
+ return ret;
+ }
+
+ ret = tasdevice_dspfw_ready(fw_entry, tas_priv);
+ release_firmware(fw_entry);
+ fw_entry = NULL;
+
+ return ret;
+}
+
+/* DSP firmware program block data remove function. */
+static void tasdev_dsp_prog_blk_remove(struct tasdevice_prog *prog)
+{
+ struct tasdevice_data *tas_dt;
+ struct tasdev_blk *blk;
+ unsigned int i;
+
+ if (!prog)
+ return;
+
+ tas_dt = &prog->dev_data;
+
+ if (!tas_dt->dev_blks)
+ return;
+
+ for (i = 0; i < tas_dt->nr_blk; i++) {
+ blk = &tas_dt->dev_blks[i];
+ kfree(blk->data);
+ }
+ kfree(tas_dt->dev_blks);
+}
+
+/* DSP firmware program block data remove function. */
+static void tasdev_dsp_prog_remove(struct tasdevice_prog *prog,
+ unsigned short nr)
+{
+ int i;
+
+ for (i = 0; i < nr; i++)
+ tasdev_dsp_prog_blk_remove(&prog[i]);
+ kfree(prog);
+}
+
+/* DSP firmware config block data remove function. */
+static void tasdev_dsp_cfg_blk_remove(struct tasdevice_config *cfg)
+{
+ struct tasdevice_data *tas_dt;
+ struct tasdev_blk *blk;
+ unsigned int i;
+
+ if (cfg) {
+ tas_dt = &cfg->dev_data;
+
+ if (!tas_dt->dev_blks)
+ return;
+
+ for (i = 0; i < tas_dt->nr_blk; i++) {
+ blk = &tas_dt->dev_blks[i];
+ kfree(blk->data);
+ }
+ kfree(tas_dt->dev_blks);
+ }
+}
+
+/* DSP firmware config remove function. */
+static void tasdev_dsp_cfg_remove(struct tasdevice_config *config,
+ unsigned short nr)
+{
+ int i;
+
+ for (i = 0; i < nr; i++)
+ tasdev_dsp_cfg_blk_remove(&config[i]);
+ kfree(config);
+}
+
+/* DSP firmware remove function. */
+void tasdevice_spi_dsp_remove(void *context)
+{
+ struct tasdevice_priv *tas_dev = context;
+
+ if (!tas_dev->fmw)
+ return;
+
+ if (tas_dev->fmw->programs)
+ tasdev_dsp_prog_remove(tas_dev->fmw->programs,
+ tas_dev->fmw->nr_programs);
+ if (tas_dev->fmw->configs)
+ tasdev_dsp_cfg_remove(tas_dev->fmw->configs,
+ tas_dev->fmw->nr_configurations);
+ kfree(tas_dev->fmw);
+ tas_dev->fmw = NULL;
+}
+
+/* DSP firmware calibration data remove function. */
+static void tas2781_clear_calfirmware(struct tasdevice_fw *tas_fmw)
+{
+ struct tasdevice_calibration *calibration;
+ struct tasdev_blk *block;
+ unsigned int blks;
+ int i;
+
+ if (!tas_fmw->calibrations)
+ goto out;
+
+ for (i = 0; i < tas_fmw->nr_calibrations; i++) {
+ calibration = &tas_fmw->calibrations[i];
+ if (!calibration)
+ continue;
+
+ if (!calibration->dev_data.dev_blks)
+ continue;
+
+ for (blks = 0; blks < calibration->dev_data.nr_blk; blks++) {
+ block = &calibration->dev_data.dev_blks[blks];
+ if (!block)
+ continue;
+ kfree(block->data);
+ }
+ kfree(calibration->dev_data.dev_blks);
+ }
+ kfree(tas_fmw->calibrations);
+out:
+ kfree(tas_fmw);
+}
+
+/* Calibration data from firmware remove function. */
+void tasdevice_spi_calbin_remove(void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+
+ if (tas_priv->cali_data_fmw) {
+ tas2781_clear_calfirmware(tas_priv->cali_data_fmw);
+ tas_priv->cali_data_fmw = NULL;
+ }
+}
+
+/* Configuration remove function. */
+void tasdevice_spi_config_info_remove(void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_rca *rca = &tas_priv->rcabin;
+ struct tasdevice_config_info **ci = rca->cfg_info;
+ unsigned int i, j;
+
+ if (!ci)
+ return;
+ for (i = 0; i < rca->ncfgs; i++) {
+ if (!ci[i])
+ continue;
+ if (ci[i]->blk_data) {
+ for (j = 0; j < ci[i]->real_nblocks; j++) {
+ if (!ci[i]->blk_data[j])
+ continue;
+ kfree(ci[i]->blk_data[j]->regdata);
+ kfree(ci[i]->blk_data[j]);
+ }
+ kfree(ci[i]->blk_data);
+ }
+ kfree(ci[i]);
+ }
+ kfree(ci);
+}
+
+/* DSP firmware program block data load function. */
+static int tasdevice_load_data(struct tasdevice_priv *tas_priv,
+ struct tasdevice_data *dev_data)
+{
+ struct tasdev_blk *block;
+ unsigned int i;
+ int ret = 0;
+
+ for (i = 0; i < dev_data->nr_blk; i++) {
+ block = &dev_data->dev_blks[i];
+ ret = tas_priv->tasdevice_load_block(tas_priv, block);
+ if (ret < 0)
+ break;
+ }
+
+ return ret;
+}
+
+/* DSP firmware program load function. */
+int tasdevice_spi_select_tuningprm_cfg(void *context, int prm_no,
+ int cfg_no, int rca_conf_no)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_rca *rca = &tas_priv->rcabin;
+ struct tasdevice_config_info **cfg_info = rca->cfg_info;
+ struct tasdevice_fw *tas_fmw = tas_priv->fmw;
+ struct tasdevice_prog *program;
+ struct tasdevice_config *conf;
+ int prog_status = 0;
+ int status;
+
+ if (!tas_fmw) {
+ dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__);
+ return 0;
+ }
+
+ if (cfg_no >= tas_fmw->nr_configurations) {
+ dev_err(tas_priv->dev,
+ "%s: cfg(%d) is not in range of conf %u\n",
+ __func__, cfg_no, tas_fmw->nr_configurations);
+ return 0;
+ }
+
+ if (prm_no >= tas_fmw->nr_programs) {
+ dev_err(tas_priv->dev,
+ "%s: prm(%d) is not in range of Programs %u\n",
+ __func__, prm_no, tas_fmw->nr_programs);
+ return 0;
+ }
+
+ if (rca_conf_no >= rca->ncfgs ||
+ rca_conf_no < 0 ||
+ !cfg_info) {
+ dev_err(tas_priv->dev,
+ "conf_no:%d should be in range from 0 to %u\n",
+ rca_conf_no, rca->ncfgs-1);
+ return 0;
+ }
+
+ if (prm_no >= 0 &&
+ (tas_priv->cur_prog != prm_no ||
+ tas_priv->force_fwload_status)) {
+ tas_priv->cur_conf = -1;
+ tas_priv->is_loading = true;
+ prog_status++;
+ }
+
+ if (prog_status) {
+ program = &tas_fmw->programs[prm_no];
+ tasdevice_load_data(tas_priv, &program->dev_data);
+ if (tas_priv->is_loaderr == false &&
+ tas_priv->is_loading == true) {
+ struct tasdevice_fw *cal_fmw =
+ tas_priv->cali_data_fmw;
+
+ if (cal_fmw) {
+ struct tasdevice_calibration
+ *cal = cal_fmw->calibrations;
+
+ if (cal)
+ load_calib_data(tas_priv,
+ &cal->dev_data);
+ }
+ tas_priv->cur_prog = prm_no;
+ }
+
+ }
+
+ if (cfg_no &&
+ (cfg_no != tas_priv->cur_conf) &&
+ (tas_priv->is_loaderr == false)) {
+ status++;
+ tas_priv->is_loading = true;
+ } else {
+ tas_priv->is_loading = false;
+ }
+
+ if (status) {
+ conf = &tas_fmw->configs[cfg_no];
+ status = 0;
+ tasdevice_load_data(tas_priv, &conf->dev_data);
+ if (tas_priv->is_loaderr == true) {
+ status |= 1 << 4;
+ } else if (tas_priv->is_loaderr == false &&
+ tas_priv->is_loading == true) {
+ tas_priv->cur_conf = cfg_no;
+ }
+ } else {
+ dev_dbg(tas_priv->dev, "%s: Unneeded loading dsp conf %d\n",
+ __func__, cfg_no);
+ }
+
+ return prog_status;
+}
+
+/* DSP firmware program load interface function. */
+int tasdevice_spi_prmg_load(void *context, int prm_no)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_fw *tas_fmw = tas_priv->fmw;
+ struct tasdevice_prog *program;
+ int prog_status = 0;
+
+ if (!tas_fmw) {
+ dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__);
+ return 0;
+ }
+
+ if (prm_no >= tas_fmw->nr_programs) {
+ dev_err(tas_priv->dev,
+ "%s: prm(%d) is not in range of Programs %u\n",
+ __func__, prm_no, tas_fmw->nr_programs);
+ return 0;
+ }
+
+ if (prm_no >= 0 && tas_priv->cur_prog != prm_no) {
+ tas_priv->cur_conf = -1;
+ tas_priv->is_loading = true;
+ prog_status++;
+ }
+ if (prog_status) {
+ program = &tas_fmw->programs[prm_no];
+ tasdevice_load_data(tas_priv, &program->dev_data);
+ if ((tas_priv->is_loaderr == false) &&
+ (tas_priv->is_loading == true))
+ tas_priv->cur_prog = prm_no;
+ }
+
+ return prog_status;
+}
+
+/* DSP firmware program switch interface function. */
+void tasdevice_spi_tuning_switch(void *context, int state)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tasdevice_fw *tas_fmw = tas_priv->fmw;
+ int profile_cfg_id = tas_priv->rcabin.profile_cfg_id;
+
+ if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) {
+ dev_err(tas_priv->dev, "DSP bin file not loaded\n");
+ return;
+ }
+
+ if (state == 0) {
+ if (tas_priv->cur_prog < tas_fmw->nr_programs) {
+ /* dsp mode or tuning mode */
+ profile_cfg_id = tas_priv->rcabin.profile_cfg_id;
+ tasdevice_spi_select_tuningprm_cfg(tas_priv,
+ tas_priv->cur_prog, tas_priv->cur_conf,
+ profile_cfg_id);
+ }
+
+ tasdevice_spi_select_cfg_blk(tas_priv, profile_cfg_id,
+ TASDEVICE_BIN_BLK_PRE_POWER_UP);
+ } else {
+ tasdevice_spi_select_cfg_blk(tas_priv, profile_cfg_id,
+ TASDEVICE_BIN_BLK_PRE_SHUTDOWN);
+ }
+}
--
2.40.1
Powered by blists - more mailing lists