[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20240724114225.2176448-6-quic_mdalam@quicinc.com>
Date: Wed, 24 Jul 2024 17:12:22 +0530
From: Md Sadre Alam <quic_mdalam@...cinc.com>
To: broonie@...nel.org, robh@...nel.org, krzk+dt@...nel.org,
conor+dt@...nel.org, andersson@...nel.org, konrad.dybcio@...aro.org,
miquel.raynal@...tlin.com, richard@....at, vigneshr@...com,
manivannan.sadhasivam@...aro.org, esben@...nix.com,
linux-arm-msm@...r.kernel.org, linux-spi@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-mtd@...ts.infradead.org
Cc: quic_mdalam@...cinc.com, quic_varada@...cinc.com,
quic_srichara@...cinc.com
Subject: [PATCH v7 5/8] mtd: rawnand: qcom: use FIELD_PREP and GENMASK
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Signed-off-by: Md Sadre Alam <quic_mdalam@...cinc.com>
---
Change in [v7]
* No change
Change in [v6]
* Added FIELD_PREP() and GENMASK() macro
Change in [v5]
* This patch was not included in [v1]
Change in [v4]
* This patch was not included in [v4]
Change in [v3]
* This patch was not included in [v3]
Change in [v2]
* This patch was not included in [v2]
Change in [v1]
* This patch was not included in [v1]
drivers/mtd/nand/raw/qcom_nandc.c | 97 ++++++++++++++--------------
include/linux/mtd/nand-qpic-common.h | 31 +++++----
2 files changed, 67 insertions(+), 61 deletions(-)
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index cced35d6d870..5028969f2fbf 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -274,7 +274,7 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i
(num_cw - 1) << CW_PER_PAGE;
cfg1 = host->cfg1_raw;
- ecc_bch_cfg = 1 << ECC_CFG_ECC_DISABLE;
+ ecc_bch_cfg = ECC_CFG_ECC_DISABLE;
}
nandc->regs->cmd = cmd;
@@ -1485,42 +1485,41 @@ static int qcom_nand_attach_chip(struct nand_chip *chip)
host->cw_size = host->cw_data + ecc->bytes;
bad_block_byte = mtd->writesize - host->cw_size * (cwperpage - 1) + 1;
- host->cfg0 = (cwperpage - 1) << CW_PER_PAGE
- | host->cw_data << UD_SIZE_BYTES
- | 0 << DISABLE_STATUS_AFTER_WRITE
- | 5 << NUM_ADDR_CYCLES
- | host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_RS
- | 0 << STATUS_BFR_READ
- | 1 << SET_RD_MODE_AFTER_STATUS
- | host->spare_bytes << SPARE_SIZE_BYTES;
-
- host->cfg1 = 7 << NAND_RECOVERY_CYCLES
- | 0 << CS_ACTIVE_BSY
- | bad_block_byte << BAD_BLOCK_BYTE_NUM
- | 0 << BAD_BLOCK_IN_SPARE_AREA
- | 2 << WR_RD_BSY_GAP
- | wide_bus << WIDE_FLASH
- | host->bch_enabled << ENABLE_BCH_ECC;
-
- host->cfg0_raw = (cwperpage - 1) << CW_PER_PAGE
- | host->cw_size << UD_SIZE_BYTES
- | 5 << NUM_ADDR_CYCLES
- | 0 << SPARE_SIZE_BYTES;
-
- host->cfg1_raw = 7 << NAND_RECOVERY_CYCLES
- | 0 << CS_ACTIVE_BSY
- | 17 << BAD_BLOCK_BYTE_NUM
- | 1 << BAD_BLOCK_IN_SPARE_AREA
- | 2 << WR_RD_BSY_GAP
- | wide_bus << WIDE_FLASH
- | 1 << DEV0_CFG1_ECC_DISABLE;
-
- host->ecc_bch_cfg = !host->bch_enabled << ECC_CFG_ECC_DISABLE
- | 0 << ECC_SW_RESET
- | host->cw_data << ECC_NUM_DATA_BYTES
- | 1 << ECC_FORCE_CLK_OPEN
- | ecc_mode << ECC_MODE
- | host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH;
+ host->cfg0 = FIELD_PREP(CW_PER_PAGE_MASK, (cwperpage - 1)) |
+ FIELD_PREP(UD_SIZE_BYTES_MASK, host->cw_data) |
+ FIELD_PREP(DISABLE_STATUS_AFTER_WRITE, 0) |
+ FIELD_PREP(NUM_ADDR_CYCLES_MASK, 5) |
+ FIELD_PREP(ECC_PARITY_SIZE_BYTES_RS, host->ecc_bytes_hw) |
+ FIELD_PREP(STATUS_BFR_READ, 0) |
+ FIELD_PREP(SET_RD_MODE_AFTER_STATUS, 1) |
+ FIELD_PREP(SPARE_SIZE_BYTES_MASK, host->spare_bytes);
+
+ host->cfg1 = FIELD_PREP(NAND_RECOVERY_CYCLES_MASK, 7) |
+ FIELD_PREP(BAD_BLOCK_BYTE_NUM_MASK, bad_block_byte) |
+ FIELD_PREP(BAD_BLOCK_IN_SPARE_AREA, 0) |
+ FIELD_PREP(WR_RD_BSY_GAP_MASK, 2) |
+ FIELD_PREP(WIDE_FLASH, wide_bus) |
+ FIELD_PREP(ENABLE_BCH_ECC, host->bch_enabled);
+
+ host->cfg0_raw = FIELD_PREP(CW_PER_PAGE_MASK, (cwperpage - 1)) |
+ FIELD_PREP(UD_SIZE_BYTES_MASK, host->cw_size) |
+ FIELD_PREP(NUM_ADDR_CYCLES_MASK, 5) |
+ FIELD_PREP(SPARE_SIZE_BYTES_MASK, 0);
+
+ host->cfg1_raw = FIELD_PREP(NAND_RECOVERY_CYCLES_MASK, 7) |
+ FIELD_PREP(CS_ACTIVE_BSY, 0) |
+ FIELD_PREP(BAD_BLOCK_BYTE_NUM_MASK, 17) |
+ FIELD_PREP(BAD_BLOCK_IN_SPARE_AREA, 1) |
+ FIELD_PREP(WR_RD_BSY_GAP_MASK, 2) |
+ FIELD_PREP(WIDE_FLASH, wide_bus) |
+ FIELD_PREP(DEV0_CFG1_ECC_DISABLE, 1);
+
+ host->ecc_bch_cfg = FIELD_PREP(ECC_CFG_ECC_DISABLE, !host->bch_enabled) |
+ FIELD_PREP(ECC_SW_RESET, 0) |
+ FIELD_PREP(ECC_NUM_DATA_BYTES_MASK, host->cw_data) |
+ FIELD_PREP(ECC_FORCE_CLK_OPEN, 1) |
+ FIELD_PREP(ECC_MODE_MASK, ecc_mode) |
+ FIELD_PREP(ECC_PARITY_SIZE_BYTES_BCH_MASK, host->ecc_bytes_hw);
if (!nandc->props->qpic_version2)
host->ecc_buf_cfg = 0x203 << NUM_STEPS;
@@ -1874,21 +1873,21 @@ static int qcom_param_page_type_exec(struct nand_chip *chip, const struct nand_
nandc->regs->addr0 = 0;
nandc->regs->addr1 = 0;
- nandc->regs->cfg0 = 0 << CW_PER_PAGE
- | 512 << UD_SIZE_BYTES
- | 5 << NUM_ADDR_CYCLES
- | 0 << SPARE_SIZE_BYTES;
+ host->cfg0 = FIELD_PREP(CW_PER_PAGE_MASK, 0) |
+ FIELD_PREP(UD_SIZE_BYTES_MASK, 512) |
+ FIELD_PREP(NUM_ADDR_CYCLES_MASK, 5) |
+ FIELD_PREP(SPARE_SIZE_BYTES_MASK, 0);
- nandc->regs->cfg1 = 7 << NAND_RECOVERY_CYCLES
- | 0 << CS_ACTIVE_BSY
- | 17 << BAD_BLOCK_BYTE_NUM
- | 1 << BAD_BLOCK_IN_SPARE_AREA
- | 2 << WR_RD_BSY_GAP
- | 0 << WIDE_FLASH
- | 1 << DEV0_CFG1_ECC_DISABLE;
+ host->cfg1 = FIELD_PREP(NAND_RECOVERY_CYCLES_MASK, 7) |
+ FIELD_PREP(BAD_BLOCK_BYTE_NUM_MASK, 17) |
+ FIELD_PREP(CS_ACTIVE_BSY, 0) |
+ FIELD_PREP(BAD_BLOCK_IN_SPARE_AREA, 1) |
+ FIELD_PREP(WR_RD_BSY_GAP_MASK, 2) |
+ FIELD_PREP(WIDE_FLASH, 0) |
+ FIELD_PREP(DEV0_CFG1_ECC_DISABLE, 1);
if (!nandc->props->qpic_version2)
- nandc->regs->ecc_buf_cfg = 1 << ECC_CFG_ECC_DISABLE;
+ nandc->regs->ecc_buf_cfg = ECC_CFG_ECC_DISABLE;
/* configure CMD1 and VLD for ONFI param probing in QPIC v1 */
if (!nandc->props->qpic_version2) {
diff --git a/include/linux/mtd/nand-qpic-common.h b/include/linux/mtd/nand-qpic-common.h
index 17d9d131639f..a4819db31034 100644
--- a/include/linux/mtd/nand-qpic-common.h
+++ b/include/linux/mtd/nand-qpic-common.h
@@ -70,35 +70,42 @@
#define BS_CORRECTABLE_ERR_MSK 0x1f
/* NAND_DEVn_CFG0 bits */
-#define DISABLE_STATUS_AFTER_WRITE 4
+#define DISABLE_STATUS_AFTER_WRITE BIT(4)
#define CW_PER_PAGE 6
+#define CW_PER_PAGE_MASK GENMASK(8, 6)
#define UD_SIZE_BYTES 9
#define UD_SIZE_BYTES_MASK GENMASK(18, 9)
-#define ECC_PARITY_SIZE_BYTES_RS 19
+#define ECC_PARITY_SIZE_BYTES_RS GENMASK(22, 19)
#define SPARE_SIZE_BYTES 23
#define SPARE_SIZE_BYTES_MASK GENMASK(26, 23)
#define NUM_ADDR_CYCLES 27
-#define STATUS_BFR_READ 30
-#define SET_RD_MODE_AFTER_STATUS 31
+#define NUM_ADDR_CYCLES_MASK GENMASK(29, 27)
+#define STATUS_BFR_READ BIT(30)
+#define SET_RD_MODE_AFTER_STATUS BIT(31)
/* NAND_DEVn_CFG0 bits */
-#define DEV0_CFG1_ECC_DISABLE 0
-#define WIDE_FLASH 1
+#define DEV0_CFG1_ECC_DISABLE BIT(0)
+#define WIDE_FLASH BIT(1)
#define NAND_RECOVERY_CYCLES 2
-#define CS_ACTIVE_BSY 5
+#define NAND_RECOVERY_CYCLES_MASK GENMASK(4, 2)
+#define CS_ACTIVE_BSY BIT(5)
#define BAD_BLOCK_BYTE_NUM 6
-#define BAD_BLOCK_IN_SPARE_AREA 16
+#define BAD_BLOCK_BYTE_NUM_MASK GENMASK(15, 6)
+#define BAD_BLOCK_IN_SPARE_AREA BIT(16)
#define WR_RD_BSY_GAP 17
-#define ENABLE_BCH_ECC 27
+#define WR_RD_BSY_GAP_MASK GENMASK(22, 17)
+#define ENABLE_BCH_ECC BIT(27)
/* NAND_DEV0_ECC_CFG bits */
-#define ECC_CFG_ECC_DISABLE 0
-#define ECC_SW_RESET 1
+#define ECC_CFG_ECC_DISABLE BIT(0)
+#define ECC_SW_RESET BIT(1)
#define ECC_MODE 4
+#define ECC_MODE_MASK GENMASK(5, 4)
#define ECC_PARITY_SIZE_BYTES_BCH 8
+#define ECC_PARITY_SIZE_BYTES_BCH_MASK GENMASK(12, 8)
#define ECC_NUM_DATA_BYTES 16
#define ECC_NUM_DATA_BYTES_MASK GENMASK(25, 16)
-#define ECC_FORCE_CLK_OPEN 30
+#define ECC_FORCE_CLK_OPEN BIT(30)
/* NAND_DEV_CMD1 bits */
#define READ_ADDR 0
--
2.34.1
Powered by blists - more mailing lists