lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <f80996c2-c3ee-430a-9ae6-2a9c524b5d60@ti.com>
Date: Wed, 7 Aug 2024 12:58:20 +0530
From: "Kumar, Udit" <u-kumar1@...com>
To: Manorit Chawdhry <m-chawdhry@...com>, Nishanth Menon <nm@...com>,
        Vignesh
 Raghavendra <vigneshr@...com>,
        Tero Kristo <kristo@...nel.org>, Rob Herring
	<robh@...nel.org>,
        Krzysztof Kozlowski <krzk+dt@...nel.org>,
        Conor Dooley
	<conor+dt@...nel.org>
CC: <linux-arm-kernel@...ts.infradead.org>, <devicetree@...r.kernel.org>,
        <linux-kernel@...r.kernel.org>, Neha Malcom Francis <n-francis@...com>,
        Aniket Limaye <a-limaye@...com>, Beleswar Padhi <b-padhi@...com>,
        Siddharth
 Vadapalli <s-vadapalli@...com>
Subject: Re: [PATCH v3 5/5] arm64: dts: ti: k3-j7200*: Add bootph-* properties


On 7/30/2024 3:23 PM, Manorit Chawdhry wrote:
> Adds bootph-* properties to the leaf nodes to enable U-boot to
> utilise them.
>
> Signed-off-by: Manorit Chawdhry <m-chawdhry@...com>
> ---
>   .../arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 20 ++++++++++++++++++++
>   arch/arm64/boot/dts/ti/k3-j7200-main.dtsi            |  2 ++
>   arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 10 ++++++++++
>   arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi          |  7 +++++++
>   4 files changed, 39 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 6593c5da82c0..ec522595fc83 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> [..]
>   
>   
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index 9386bf3ef9f6..b95656942412 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -136,6 +136,7 @@ secure_proxy_main: mailbox@...00000 {
>   			      <0x00 0x32800000 0x00 0x100000>;
>   			interrupt-names = "rx_011";
>   			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +			bootph-all;
>   		};
>   
>   		hwspinlock: spinlock@...00000 {
> @@ -1528,5 +1529,6 @@ main_esm: esm@...000 {
>   		compatible = "ti,j721e-esm";
>   		reg = <0x0 0x700000 0x0 0x1000>;
>   		ti,esm-pins = <656>, <657>;
> +		bootph-all;

Should be bootph-pre-ram

if you think otherwise then please update mcu_esm

>   	};
>   };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> index 5097d192c2b2..f8a5ad4737da 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> @@ -21,16 +21,19 @@ dmsc: system-controller@...83000 {
>   		k3_pds: power-controller {
>   			compatible = "ti,sci-pm-domain";
>   			#power-domain-cells = <2>;
> +			bootph-all;
>   		};
>   
>   		k3_clks: clock-controller {
>   			compatible = "ti,k2g-sci-clk";
>   			#clock-cells = <2>;
> +			bootph-all;
>   		};
>   
>   		k3_reset: reset-controller {
>   			compatible = "ti,sci-reset";
>   			#reset-cells = <2>;
> +			bootph-all;
>   		};
>   	};
>   
> @@ -45,6 +48,7 @@ mcu_timer0: timer@...00000 {
>   		assigned-clock-parents = <&k3_clks 35 2>;
>   		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
>   		ti,timer-pwm;
> +		bootph-pre-ram;

I see this node is marked as reserved

Do we plan to use in bootloader ?

>   	};
>   
>   	mcu_timer1: timer@...10000 {
> @@ -191,6 +195,7 @@ wkup_conf: bus@...00000 {
>   		chipid: chipid@14 {
>   			compatible = "ti,am654-chipid";
>   			reg = <0x14 0x4>;
> [...]
> @@ -389,6 +396,7 @@ secure_proxy_mcu: mailbox@...80000 {
>   		 * firmware on non-MPU processors
>   		 */
>   		status = "disabled";
> +		bootph-pre-ram;
>   	};
>   
>   	mcu_cpsw: ethernet@...00000 {
> @@ -534,6 +542,7 @@ hbmc_mux: mux-controller@...00004 {
>   			reg = <0x00 0x47000004 0x00 0x4>;
>   			#mux-control-cells = <1>;
>   			mux-reg-masks = <0x0 0x2>; /* HBMC select */
> +			bootph-pre-ram;
>   		};
>   
>   		hbmc: hyperbus@...34000 {

I think you should consider to mark hbmc node for boot phase as well


> @@ -652,6 +661,7 @@ wkup_vtm0: temperature-sensor@...40000 {
>   		      <0x00 0x42050000 0x00 0x350>;
>   		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
>   		#thermal-sensor-cells = <1>;
> +		bootph-pre-ram;
>   	};
>   
>   	mcu_esm: esm@...00000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> index 21fe194a5766..d78f86889bf9 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> @@ -121,6 +121,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
>   			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
>   			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
>   		>;
> [..]
>   			bucka2: buck2 {
> @@ -464,6 +470,7 @@ flash@0 {
>   		cdns,tchsh-ns = <60>;
>   		cdns,tslch-ns = <60>;
>   		cdns,read-delay = <4>;
> +		bootph-all;
>   
>   		partitions {
>   			compatible = "fixed-partitions";


Please consider, adding bootph in ospi0 node as well around 
"ospi.phypattern"


>

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ