lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <13fa9b3f-7124-4851-a1e3-7ea93ac7ba48@tuxon.dev>
Date: Fri, 9 Aug 2024 09:15:03 +0300
From: claudiu beznea <claudiu.beznea@...on.dev>
To: Alexander Dahl <ada@...rsis.com>, devicetree@...r.kernel.org
Cc: Rob Herring <robh@...nel.org>, Conor Dooley <conor+dt@...nel.org>,
 linux-kernel@...r.kernel.org, Krzysztof Kozlowski <krzk+dt@...nel.org>,
 linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH] ARM: dts: microchip: sam9x60: Move i2c address/size to
 dtsi



On 28.05.2024 18:31, Alexander Dahl wrote:
> These properties are common for all i2c subnodes, and marked as
> 'required' in atmel/microchip i2c bindings.  Allows to add i2c device
> nodes (like an rtc for example) in other .dts files including
> sam9x60.dtsi without requiring to repeat these properties for each i2c
> device again and again.
> 
> Found on a custom board after adding this in .dts:
> 
>     &flx5 {
>             atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
>             status = "okay";
> 
>             i2c5: i2c@600 {
>                     pinctrl-0 = <&pinctrl_flx5_default>;
>                     status = "okay";
> 
>                     pcf8523: rtc@68 {
>                             compatible = "nxp,pcf8523";
>                             reg = <0x68>;
>                     };
>             };
>     };
> 
> … which created a warning like this:
> 
>     […]:236.4-17: Warning (reg_format): 
> /ahb/apb/flexcom@...04000/i2c@.../rtc@68:reg: property has invalid 
> length (4 bytes) (#address-cells == 2, #size-cells == 1)
>     […]: Warning (pci_device_reg): Failed prerequisite 'reg_format'
>     […]: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
>     […]: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
>     
> […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: 
> Warning (i2c_bus_bridge): /ahb/apb/flexcom@...04000/i2c@600: incorrect 
> #address-cells for I2C bus also defined at […]:228.16-238.4
>     
> […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: 
> Warning (i2c_bus_bridge): /ahb/apb/flexcom@...04000/i2c@600: incorrect 
> #size-cells for I2C bus also defined at […]:228.16-238.4
>     […]: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
>     […]: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
>     […]: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
>     […]:234.19-237.5: Warning (avoid_default_addr_size): 
> /ahb/apb/flexcom@...04000/i2c@.../rtc@68: Relying on default 
> #address-cells value
>     […]:234.19-237.5: Warning (avoid_default_addr_size): 
> /ahb/apb/flexcom@...04000/i2c@.../rtc@68: Relying on default #size-cells
>  value
>     […]: Warning (avoid_unnecessary_addr_size): Failed prerequisite 
> 'avoid_default_addr_size'
>     […]: Warning (unique_unit_address): Failed prerequisite 
> 'avoid_default_addr_size'
> 
> This probably should have been done with commit 84f23f3284d5 ("ARM: dts:
> at91: sam9x60: move flexcom definitions") already, where those
> address-cells and size-cells properties were left in the board .dts
> files instead of moving them to the dtsi.
> 
> Signed-off-by: Alexander Dahl <ada@...rsis.com>


Applied to at91-dt, thanks!

Please note that I've adjusted the commit message to reflect that the props
you've adjusted are not required anymore in the validation schema.

Thank you,
Claudiu Beznea

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ