[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <20240816221721.GA2362530-robh@kernel.org>
Date: Fri, 16 Aug 2024 16:17:21 -0600
From: Rob Herring <robh@...nel.org>
To: Frank Li <Frank.Li@....com>
Cc: Krzysztof Kozlowski <krzk@...nel.org>,
MyungJoo Ham <myungjoo.ham@...sung.com>,
Chanwoo Choi <cw00.choi@...sung.com>,
Conor Dooley <conor+dt@...nel.org>,
"open list:NXP PTN5150A CC LOGIC AND EXTCON DRIVER" <linux-kernel@...r.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" <devicetree@...r.kernel.org>,
imx@...ts.linux.dev
Subject: Re: [PATCH v2 1/1] dt-bindings: extcon: ptn5150: add child node port
On Thu, Aug 15, 2024 at 04:32:44PM -0400, Frank Li wrote:
> Add child node 'port' to allow connect to usb controller to do role-switch.
> Add example for id pin of ptn5150 have not connect to main chip's usb id
> pin.
>
> Fix below warning:
> arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dtb: typec@3d: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml
>
> Signed-off-by: Frank Li <Frank.Li@....com>
> ---
> Change from v1 to v2
> - add example for id pin have not connect to main chip's id example.
> - commit 095b96b2b fix "port" warning, but add new warning "connector" is
> not exist. And follow commit revert this change.
> 690085d866f08 Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector
> - I have not board in hand to debug why "connector" is not work.
> ---
> .../bindings/extcon/extcon-ptn5150.yaml | 46 +++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> index d5cfa32ea52dd..39231f9952826 100644
> --- a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
> @@ -37,6 +37,11 @@ properties:
> GPIO pin (output) used to control VBUS. If skipped, no such control
> takes place.
>
> + port:
> + $ref: /schemas/graph.yaml#/properties/port
> + description:
> + A port node to link the usb controller for the dual role switch.
> +
> required:
> - compatible
> - interrupts
> @@ -60,3 +65,44 @@ examples:
> vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
> };
> };
> +
> + - |
> + /* id pin of ptn5150 have not connected to chip's id pin */
> + #include <dt-bindings/clock/imx8mn-clock.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
Just add 'port' to the existing example if you want to. Don't need a
whole other example just for that.
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ptn5150@1d {
> + compatible = "nxp,ptn5150";
> + reg = <0x1d>;
> + interrupt-parent = <&msmgpio>;
> + interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
> + vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + typec1_dr_sw: endpoint {
> + remote-endpoint = <&usb1_drd_sw>;
> + };
> + };
> + };
> + };
> +
> + usb@...40000 {
> + compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb", "fsl,imx27-usb";
> + reg = <0x32e40000 0x200>;
> + interrupts = <&gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MN_CLK_USB1_CTRL_ROOT>;
> + usb-role-switch;
> +
> + port {
> + usb1_drd_sw: endpoint {
> + remote-endpoint = <&typec1_dr_sw>;
> + };
> + };
> + };
> +
> --
> 2.34.1
>
Powered by blists - more mailing lists