[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240816062017.970364-1-quic_prashk@quicinc.com>
Date: Fri, 16 Aug 2024 11:50:17 +0530
From: Prashanth K <quic_prashk@...cinc.com>
To: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Thinh Nguyen
<Thinh.Nguyen@...opsys.com>
CC: <linux-kernel@...r.kernel.org>, <linux-usb@...r.kernel.org>,
Prashanth K
<quic_prashk@...cinc.com>, <stable@...r.kernel.org>
Subject: [v2] usb: dwc3: Avoid waking up gadget during startxfer
When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a56 ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@...r.kernel.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@...opsys.com>
Signed-off-by: Prashanth K <quic_prashk@...cinc.com>
---
v2: Refactored the patch as suggested in v1 discussion.
drivers/usb/dwc3/gadget.c | 24 ------------------------
1 file changed, 24 deletions(-)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 89fc690fdf34..3f634209c5b8 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -327,30 +327,6 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
}
- if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
- int link_state;
-
- /*
- * Initiate remote wakeup if the link state is in U3 when
- * operating in SS/SSP or L1/L2 when operating in HS/FS. If the
- * link state is in U1/U2, no remote wakeup is needed. The Start
- * Transfer command will initiate the link recovery.
- */
- link_state = dwc3_gadget_get_link_state(dwc);
- switch (link_state) {
- case DWC3_LINK_STATE_U2:
- if (dwc->gadget->speed >= USB_SPEED_SUPER)
- break;
-
- fallthrough;
- case DWC3_LINK_STATE_U3:
- ret = __dwc3_gadget_wakeup(dwc, false);
- dev_WARN_ONCE(dwc->dev, ret, "wakeup failed --> %d\n",
- ret);
- break;
- }
- }
-
/*
* For some commands such as Update Transfer command, DEPCMDPARn
* registers are reserved. Since the driver often sends Update Transfer
--
2.25.1
Powered by blists - more mailing lists