[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240822141622.tw7vcoc4ciwbydsw@thinkpad>
Date: Thu, 22 Aug 2024 19:46:22 +0530
From: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To: Krzysztof Kozlowski <krzk@...nel.org>
Cc: Krishna Chaitanya Chundru <quic_krichai@...cinc.com>,
Lorenzo Pieralisi <lpieralisi@...nel.org>,
Krzysztof Wilczyński <kw@...ux.com>,
Rob Herring <robh@...nel.org>, Bjorn Helgaas <bhelgaas@...gle.com>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
cros-qcom-dts-watchers@...omium.org,
Bartosz Golaszewski <brgl@...ev.pl>,
Jingoo Han <jingoohan1@...il.com>, andersson@...nel.org,
quic_vbadigan@...cinc.com, linux-arm-msm@...r.kernel.org,
linux-pci@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
Subject: Re: [PATCH v2 1/8] dt-bindings: PCI: Add binding for qps615
On Mon, Aug 05, 2024 at 04:43:47PM +0200, Krzysztof Kozlowski wrote:
> On 05/08/2024 07:57, Krishna Chaitanya Chundru wrote:
> >>
> > Hi Krzysztof,
> >
> > QPS615 has a 3 downstream ports and 1 upstream port as described below
> > diagram.
> > For this entire switch there are some supplies which we described in the
> > dt-binding (vdd18-supply, vdd09-supply etc) and one GPIO which controls
> > reset of the switch (reset-gpio). The switch hardware can configure the
> > individual ports DSP0, DSP1, DSP2, upstream port and also one integrated
> > ethernet endpoint which is connected to DSP2(I didn't mentioned in the
> > diagram) through I2C.
> >
> > The properties other than supplies,i2c client, reset gpio which
> > are added will be applicable for all the ports.
> > _______________________________________________________________
> > | |i2c| QPS615 |Supplies||Resx gpio |
> > | |___| _________________ |________||__________|
> > | ________________| Upstream port |_____________ |
> > | | |_______________| | |
> > | | | | |
> > | | | | |
> > | ____|_____ ____|_____ ___|____ |
> > | |DSP 0 | | DSP 1 | | DSP 2| |
> > | |________| |________| |______| |
> > |_____________________________________________________________|
> >
>
> I don't get why then properties should apply to main device node.
>
The problem here is, we cannot differentiate between main device node and the
upstream node. Typically the differentiation is not needed because no one cared
about configuring the upstream port. But this PCIe switch is special (as like
most of the Qcom peripherals).
I agree that if we don't differentiate then it also implies that all main node
properties are applicable to upstream port and vice versa. But AFAIK, upstream
port is often considered as the _device_ itself as it shares the same bus
number.
- Mani
--
மணிவண்ணன் சதாசிவம்
Powered by blists - more mailing lists