linux-kernel - [PATCH 2/2] spi: atmel-quadspi: Add cs_hold and cs

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20240918082744.379610-3-ada@thorsis.com>
Date: Wed, 18 Sep 2024 10:27:44 +0200
From: Alexander Dahl <ada@...rsis.com>
To: Mark Brown <broonie@...nel.org>
Cc: Nicolas Ferre <nicolas.ferre@...rochip.com>,
	Alexandre Belloni <alexandre.belloni@...tlin.com>,
	Claudiu Beznea <claudiu.beznea@...on.dev>,
	linux-spi@...r.kernel.org (open list:SPI SUBSYSTEM),
	linux-arm-kernel@...ts.infradead.org (moderated list:ARM/Microchip (AT91) SoC support),
	linux-kernel@...r.kernel.org (open list)
Subject: [PATCH 2/2] spi: atmel-quadspi: Add cs_hold and cs_inactive setting support

spi-cs-inactive-delay-ns in dts is cs_inactive in spi core, and it maps
to DLYCS (Minimum Inactive QCS Delay) in QSPI Mode Register (QSPI_MR).

spi-cs-hold-delay-ns in dts is cs_hold in spi core, and it maps to
DLYBCT (Delay Between Consecutive Transfers) in QSPI_MR.  That one can
be set to other values than 0 only if the chip is not in Serial Memory
Mode (SMM), it must be written to '0' however when in SMM.

Tested on SAM9X60 based board with FPGA implementing custom SPI Memory
protocol.

Signed-off-by: Alexander Dahl <ada@...rsis.com>
---
 drivers/spi/atmel-quadspi.c | 36 ++++++++++++++++++++++++++++++++----
 1 file changed, 32 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c
index fcd57cf1f2cf..d46e2ca76330 100644
--- a/drivers/spi/atmel-quadspi.c
+++ b/drivers/spi/atmel-quadspi.c
@@ -516,21 +516,45 @@ static int atmel_qspi_set_cs_timing(struct spi_device *spi)
 	struct spi_controller *ctrl = spi->controller;
 	struct atmel_qspi *aq = spi_controller_get_devdata(ctrl);
 	unsigned long clk_rate;
+	u32 cs_inactive;
 	u32 cs_setup;
+	u32 cs_hold;
 	int delay;
 	int ret;
 
-	delay = spi_delay_to_ns(&spi->cs_setup, NULL);
-	if (delay <= 0)
-		return delay;
-
 	clk_rate = clk_get_rate(aq->pclk);
 	if (!clk_rate)
 		return -EINVAL;
 
+	/* hold */
+	delay = spi_delay_to_ns(&spi->cs_hold, NULL);
+	if (aq->mr & QSPI_MR_SMM) {
+		if (delay > 0)
+			dev_warn(&aq->pdev->dev,
+				 "Ignoring cs_hold, must be 0 in Serial Memory Mode.\n");
+		cs_hold = 0;
+	} else {
+		delay = spi_delay_to_ns(&spi->cs_hold, NULL);
+		if (delay < 0)
+			return delay;
+
+		cs_hold = DIV_ROUND_UP((delay * DIV_ROUND_UP(clk_rate, 1000000)), 32000);
+	}
+
+	/* setup */
+	delay = spi_delay_to_ns(&spi->cs_setup, NULL);
+	if (delay < 0)
+		return delay;
+
 	cs_setup = DIV_ROUND_UP((delay * DIV_ROUND_UP(clk_rate, 1000000)),
 				1000);
 
+	/* inactive */
+	delay = spi_delay_to_ns(&spi->cs_inactive, NULL);
+	if (delay < 0)
+		return delay;
+	cs_inactive = DIV_ROUND_UP((delay * DIV_ROUND_UP(clk_rate, 1000000)), 1000);
+
 	ret = pm_runtime_resume_and_get(ctrl->dev.parent);
 	if (ret < 0)
 		return ret;
@@ -539,6 +563,10 @@ static int atmel_qspi_set_cs_timing(struct spi_device *spi)
 	aq->scr |= QSPI_SCR_DLYBS(cs_setup);
 	atmel_qspi_write(aq->scr, aq, QSPI_SCR);
 
+	aq->mr &= ~(QSPI_MR_DLYBCT_MASK | QSPI_MR_DLYCS_MASK);
+	aq->mr |= QSPI_MR_DLYBCT(cs_hold) | QSPI_MR_DLYCS(cs_inactive);
+	atmel_qspi_write(aq->mr, aq, QSPI_MR);
+
 	pm_runtime_mark_last_busy(ctrl->dev.parent);
 	pm_runtime_put_autosuspend(ctrl->dev.parent);
 
-- 
2.39.5