[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <ZvKdmhfxilFfOzmb@linaro.org>
Date: Tue, 24 Sep 2024 14:08:10 +0300
From: Abel Vesa <abel.vesa@...aro.org>
To: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
Cc: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, Johan Hovold <johan@...nel.org>,
Neil Armstrong <neil.armstrong@...aro.org>,
Trilok Soni <quic_tsoni@...cinc.com>, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 1/2] arm64: dts: qcom: x1e80100-crd: Enable external DP
support
On 24-09-02 21:54:58, Dmitry Baryshkov wrote:
> On Mon, Sep 02, 2024 at 06:01:35PM GMT, Abel Vesa wrote:
> > The Qualcomm Snapdragon X Elite CRD board has 3 USB Type-C ports,
> > all of them supporting external DP altmode. Between each QMP
> > combo PHY and the corresponding Type-C port, sits one Parade PS8830
> > retimer which handles both orientation and SBU muxing. Add nodes for
> > each retimer, fix the graphs between connectors and the PHYs accordingly,
> > add the voltage regulators needed by each retimer and then enable all
> > 3 remaining DPUs.
> >
> > Signed-off-by: Abel Vesa <abel.vesa@...aro.org>
> > ---
> > arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 414 +++++++++++++++++++++++++++++-
> > 1 file changed, 408 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > index 10b28d870f08..6dfc85eda354 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
>
> [skipped]
>
>
> > @@ -709,6 +861,163 @@ keyboard@3a {
> > };
> > };
> >
> > +&i2c1 {
> > + clock-frequency = <400000>;
> > +
> > + status = "okay";
> > +
> > + typec-mux@8 {
> > + compatible = "parade,ps8830";
> > + reg = <0x08>;
> > +
> > + clocks = <&rpmhcc RPMH_RF_CLK5>;
> > + clock-names = "xo";
> > +
> > + vdd15-supply = <&vreg_rtmr2_1p15>;
> > + vdd18-supply = <&vreg_rtmr2_1p8>;
> > + vdd33-supply = <&vreg_rtmr2_3p3>;
> > +
> > + reset-gpios = <&tlmm 185 GPIO_ACTIVE_HIGH>;
> > +
> > + orientation-switch;
> > + retimer-switch;
>
> Doesn't it need to listen to mode switching events? 4-lane DP vs
> 2/2-lane DP + USB3 requires propagating of the altmode events to the QMP
> PHY, see the original 4-lane series.
The mode is passed through the retimer state as well, isn't it?
>
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + retimer_ss2_ss_out: endpoint {
> > + remote-endpoint = <&pmic_glink_ss2_ss_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + retimer_ss2_ss_in: endpoint {
> > + remote-endpoint = <&usb_1_ss2_qmpphy_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <2>;
> > +
> > + retimer_ss2_con_sbu_out: endpoint {
> > + remote-endpoint = <&pmic_glink_ss2_con_sbu_in>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
>
>
> > @@ -1164,7 +1566,7 @@ &usb_1_ss0_dwc3_hs {
> > };
> >
> > &usb_1_ss0_qmpphy_out {
> > - remote-endpoint = <&pmic_glink_ss0_ss_in>;
> > + remote-endpoint = <&retimer_ss0_ss_in>;
> > };
>
> orientation-switch and mode-switch for the QMP PHY?
orientation-switch is already in the SoC dtsi nodes.
But the qmp phy doesn't currently support mode switching. Right?
>
> >
> > &usb_1_ss1_hsphy {
> > @@ -1196,7 +1598,7 @@ &usb_1_ss1_dwc3_hs {
> > };
> >
> > &usb_1_ss1_qmpphy_out {
> > - remote-endpoint = <&pmic_glink_ss1_ss_in>;
> > + remote-endpoint = <&retimer_ss1_ss_in>;
> > };
> >
> > &usb_1_ss2_hsphy {
> > @@ -1228,5 +1630,5 @@ &usb_1_ss2_dwc3_hs {
> > };
> >
> > &usb_1_ss2_qmpphy_out {
> > - remote-endpoint = <&pmic_glink_ss2_ss_in>;
> > + remote-endpoint = <&retimer_ss2_ss_in>;
> > };
> >
> > --
> > 2.34.1
> >
>
> --
> With best wishes
> Dmitry
Thanks for reviewing.
Abel
Powered by blists - more mailing lists