| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20240924120044.130913-4-francesco@dolcini.it>
Date: Tue, 24 Sep 2024 14:00:44 +0200
From: Francesco Dolcini <francesco@...cini.it>
To: Nishanth Menon <nm@...com>,
Vignesh Raghavendra <vigneshr@...com>,
Tero Kristo <kristo@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: João Paulo Gonçalves <joao.goncalves@...adex.com>,
linux-arm-kernel@...ts.infradead.org,
devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Francesco Dolcini <francesco.dolcini@...adex.com>
Subject: [PATCH v1 3/3] arm64: dts: ti: k3-am62-verdin: Add Ivy carrier board
From: João Paulo Gonçalves <joao.goncalves@...adex.com>
Add Toradex Verdin Ivy carrier board support. One notable feature of Ivy
is the analog inputs. These inputs are multiplexed, allowing the same
input to measure either voltage or current. For current measurements,
a GPIO switch enables or disables the shunt resistor. This process is
automatically managed by the Linux kernel using the IIO and MUX
subsystems. Voltage measurement is always enabled, but the voltage
measured by the ADC is scaled by a cascade voltage divider. In the
device tree, the equivalent gain of the voltage divider is used, which
can be calculated as follows:
------------
+ |
.-.
R1=30K | |
| |
'-'
|-------------------
Analog Input (AIN) | |
.-. .-.
R2=10K | | R3=30K | |
| | | |
'-' '-'
| |
| |--------
| .-. +
| R4=10K | |
| | | ADC Input (Channels 0 and 1)
| '-'
- | | -
-----------| |--------
=== ===
GND GND
Vin = Analog Input (AIN)
Vout = ADC Input
Rth = Thevenin Equiv. Resistance
Vth = Thevenin Equiv. Voltage
RL = Load Resistor
R1 = 30K, R2 = 10K, R3 = 30K, R4 = 10K
RL = R4 = 10K
Rth = (R1 // R2) + R3 = 37500 Ohms
Vth = (Vin * R2) / (R1 + R2) = Vin/4;
Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19
Gain = Vout/Vin = 1/19
https://www.toradex.com/products/carrier-board/ivy-carrier-board
Signed-off-by: João Paulo Gonçalves <joao.goncalves@...adex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@...adex.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
.../arm64/boot/dts/ti/k3-am62-verdin-ivy.dtsi | 655 ++++++++++++++++++
.../dts/ti/k3-am625-verdin-nonwifi-ivy.dts | 22 +
.../boot/dts/ti/k3-am625-verdin-wifi-ivy.dts | 22 +
4 files changed, 701 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62-verdin-ivy.dtsi
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-verdin-nonwifi-ivy.dts
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-verdin-wifi-ivy.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index bcd392c3206e..72a4d576c719 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -16,10 +16,12 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-ivy.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-mallow.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-yavia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dahlia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-ivy.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-mallow.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-1-4-ghz-opp.dtbo
diff --git a/arch/arm64/boot/dts/ti/k3-am62-verdin-ivy.dtsi b/arch/arm64/boot/dts/ti/k3-am62-verdin-ivy.dtsi
new file mode 100644
index 000000000000..71c29eab0eee
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62-verdin-ivy.dtsi
@@ -0,0 +1,655 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ *
+ * Common dtsi for Verdin AM62 SoM on Ivy carrier board
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
+ * https://www.toradex.com/products/carrier-board/ivy-carrier-board
+ */
+
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ /* AIN1 Voltage w/o AIN1_MODE gpio control */
+ ain1_voltage_unmanaged: voltage-divider-ain1 {
+ compatible = "voltage-divider";
+ #io-channel-cells = <1>;
+ io-channels = <&ivy_adc1 0>;
+ full-ohms = <19>;
+ output-ohms = <1>;
+ };
+
+ /* AIN1 Current w/o AIN1_MODE gpio control */
+ ain1_current_unmanaged: current-sense-shunt-ain1 {
+ compatible = "current-sense-shunt";
+ #io-channel-cells = <0>;
+ io-channels = <&ivy_adc1 1>;
+ shunt-resistor-micro-ohms = <100000000>;
+ };
+
+ /* AIN1_MODE - SODIMM 216 */
+ ain1_mode_mux_ctrl: mux-controller-0 {
+ compatible = "gpio-mux";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_5>;
+ #mux-control-cells = <0>;
+ mux-gpios = <&main_gpio0 40 GPIO_ACTIVE_HIGH>;
+ };
+
+ ain1-voltage {
+ compatible = "io-channel-mux";
+ channels = "ain1_voltage", "";
+ io-channels = <&ain1_voltage_unmanaged 0>;
+ io-channel-names = "parent";
+ mux-controls = <&ain1_mode_mux_ctrl>;
+ settle-time-us = <1000>;
+ };
+
+ ain1-current {
+ compatible = "io-channel-mux";
+ channels = "", "ain1_current";
+ io-channels = <&ain1_current_unmanaged>;
+ io-channel-names = "parent";
+ mux-controls = <&ain1_mode_mux_ctrl>;
+ settle-time-us = <1000>;
+ };
+
+ /* AIN2 Voltage w/o AIN2_MODE gpio control */
+ ain2_voltage_unmanaged: voltage-divider-ain2 {
+ compatible = "voltage-divider";
+ #io-channel-cells = <1>;
+ io-channels = <&ivy_adc2 0>;
+ full-ohms = <19>;
+ output-ohms = <1>;
+ };
+
+ /* AIN2 Current w/o AIN2_MODE gpio control */
+ ain2_current_unmanaged: current-sense-shunt-ain2 {
+ compatible = "current-sense-shunt";
+ #io-channel-cells = <0>;
+ io-channels = <&ivy_adc2 1>;
+ shunt-resistor-micro-ohms = <100000000>;
+ };
+
+ /* AIN2_MODE - SODIMM 218 */
+ ain2_mode_mux_ctrl: mux-controller-1 {
+ compatible = "gpio-mux";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_6>;
+ #mux-control-cells = <0>;
+ mux-gpios = <&main_gpio0 36 GPIO_ACTIVE_HIGH>;
+ };
+
+ ain2-voltage {
+ compatible = "io-channel-mux";
+ channels = "ain2_voltage", "";
+ io-channels = <&ain2_voltage_unmanaged 0>;
+ io-channel-names = "parent";
+ mux-controls = <&ain2_mode_mux_ctrl>;
+ settle-time-us = <1000>;
+ };
+
+ ain2-current {
+ compatible = "io-channel-mux";
+ channels = "", "ain2_current";
+ io-channels = <&ain2_current_unmanaged>;
+ io-channel-names = "parent";
+ mux-controls = <&ain2_mode_mux_ctrl>;
+ settle-time-us = <1000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ivy_leds>;
+
+ /* D7 Blue - SODIMM 30 - LEDs.GPIO1 */
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ gpios = <&main_gpio1 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D7 Green - SODIMM 32 - LEDs.GPIO2 */
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ gpios = <&main_gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D7 Red - SODIMM 34 - LEDs.GPIO3 */
+ led-2 {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ gpios = <&main_gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D8 Blue - SODIMM 36 - LEDs.GPIO4 */
+ led-3 {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ gpios = <&main_gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D8 Green - SODIMM 54 - LEDs.GPIO5 */
+ led-4 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ gpios = <&main_gpio0 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D8 Red - SODIMM 44 - LEDs.GPIO6 */
+ led-5 {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ gpios = <&main_gpio0 37 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D9 Blue - SODIMM 46 - LEDs.GPIO7 */
+ led-6 {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <3>;
+ gpios = <&main_gpio0 34 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* D9 Red - SODIMM 48 - LEDs.GPIO8 */
+ led-7 {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <3>;
+ gpios = <&main_gpio0 33 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_3v2_ain1: regulator-3v2-ain1 {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3200000>;
+ regulator-min-microvolt = <3200000>;
+ regulator-name = "+3V2_AIN1";
+ };
+
+ reg_3v2_ain2: regulator-3v2-ain2 {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3200000>;
+ regulator-min-microvolt = <3200000>;
+ regulator-name = "+3V2_AIN2";
+ };
+
+ /* Ivy Power Supply Input Voltage */
+ ivy-input-voltage {
+ compatible = "voltage-divider";
+ /* Verdin ADC_1 */
+ io-channels = <&verdin_som_adc 7>;
+ full-ohms = <204700>; /* 200K + 4.7K */
+ output-ohms = <4700>;
+ };
+
+ ivy-5v-voltage {
+ compatible = "voltage-divider";
+ /* Verdin ADC_2 */
+ io-channels = <&verdin_som_adc 6>;
+ full-ohms = <39000>; /* 27K + 12K */
+ output-ohms = <12000>;
+ };
+
+ ivy-3v3-voltage {
+ compatible = "voltage-divider";
+ /* Verdin ADC_3 */
+ io-channels = <&verdin_som_adc 5>;
+ full-ohms = <54000>; /* 27K + 27K */
+ output-ohms = <27000>;
+ };
+
+ ivy-1v8-voltage {
+ compatible = "voltage-divider";
+ /* Verdin ADC_4 */
+ io-channels = <&verdin_som_adc 4>;
+ full-ohms = <39000>; /* 12K + 27K */
+ output-ohms = <27000>;
+ };
+};
+
+&main_pmx0 {
+ pinctrl_ivy_leds: ivy-leds-default-pins {
+ pinctrl-single,pins =
+ <AM62X_IOPAD(0x019c, PIN_INPUT, 7)>, /* (B18) MCASP0_AXR1.GPIO1_9 */ /* SODIMM 36 */
+ <AM62X_IOPAD(0x01a0, PIN_INPUT, 7)>, /* (B20) MCASP0_AXR0.GPIO1_10 */ /* SODIMM 34 */
+ <AM62X_IOPAD(0x01a4, PIN_INPUT, 7)>, /* (A19) MCASP0_ACLKX.GPIO1_11 */ /* SODIMM 30 */
+ <AM62X_IOPAD(0x01a8, PIN_INPUT, 7)>, /* (A20) MCASP0_AFSX.GPIO1_12 */ /* SODIMM 32 */
+ <AM62X_IOPAD(0x0088, PIN_INPUT, 7)>, /* (L17) GPMC0_OEn_REn.GPIO0_33 */ /* SODIMM 48 */
+ <AM62X_IOPAD(0x0098, PIN_INPUT, 7)>, /* (R18) GPMC0_WAIT0.GPIO0_37 */ /* SODIMM 44 */
+ <AM62X_IOPAD(0x008c, PIN_INPUT, 7)>, /* (L25) GPMC0_WEn.GPIO0_34 */ /* SODIMM 46 */
+ <AM62X_IOPAD(0x002c, PIN_INPUT, 7)>; /* (F23) OSPI0_CSn0.GPIO0_11 */ /* SODIMM 54 */
+ };
+};
+
+/* Verdin ETH */
+&cpsw3g {
+ status = "okay";
+};
+
+/* MDIO, shared by Verdin ETH_1 (On-module PHY) and Verdin ETH_2_RGMII */
+&cpsw3g_mdio {
+ status = "okay";
+
+ cpsw3g_phy1: ethernet-phy@2 {
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eth2_rgmii_int>;
+ interrupt-parent = <&main_gpio0>;
+ interrupts = <38 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ };
+};
+
+/* Verdin ETH_1*/
+&cpsw_port1 {
+ status = "okay";
+};
+
+/* Verdin ETH_2_RGMII */
+&cpsw_port2 {
+ phy-handle = <&cpsw3g_phy1>;
+ phy-mode = "rgmii-rxid";
+ status = "okay";
+};
+
+&main_gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ctrl_sleep_moci>,
+ <&pinctrl_qspi1_cs2_gpio>,
+ <&pinctrl_qspi1_io0_gpio>,
+ <&pinctrl_qspi1_io1_gpio>,
+ <&pinctrl_qspi1_io2_gpio>,
+ <&pinctrl_qspi1_io3_gpio>;
+ gpio-line-names =
+ "", /* 0 */
+ "",
+ "",
+ "DIGI_1", /* SODIMM 56 */
+ "DIGI_2", /* SODIMM 58 */
+ "REL1", /* SODIMM 60 */
+ "REL2", /* SODIMM 62 */
+ "",
+ "",
+ "",
+ "", /* 10 */
+ "",
+ "REL3", /* SODIMM 64 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 20 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 30 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 40 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 50 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 60 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 70 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 80 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+};
+
+&main_gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi1_dqs_gpio>;
+ gpio-line-names =
+ "", /* 0 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 10 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "REL4", /* SODIMM 66 */
+ "",
+ "", /* 20 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 30 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 40 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 50 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 60 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 70 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "", /* 80 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+};
+
+/* Verdin I2C_1 */
+&main_i2c1 {
+ status = "okay";
+
+ temperature-sensor@4f {
+ compatible = "ti,tmp1075";
+ reg = <0x4f>;
+ };
+
+ eeprom@57 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+/* Verdin I2C_4 CSI */
+&main_i2c3 {
+ status = "okay";
+
+ ivy_adc1: adc@40 {
+ compatible = "ti,ads1119";
+ reg = <0x40>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_7>;
+ interrupt-parent = <&main_gpio0>;
+ interrupts = <41 IRQ_TYPE_EDGE_FALLING>;
+ avdd-supply = <®_3v2_ain1>;
+ dvdd-supply = <®_3v2_ain1>;
+ vref-supply = <®_3v2_ain1>;
+ #address-cells = <1>;
+ #io-channel-cells = <1>;
+ #size-cells = <0>;
+
+ /* AIN1 0-33V Voltage Input */
+ channel@0 {
+ reg = <0>;
+ diff-channels = <0 1>;
+ };
+
+ /* AIN1 0-20mA Current Input */
+ channel@1 {
+ reg = <1>;
+ diff-channels = <2 3>;
+ };
+ };
+
+ ivy_adc2: adc@41 {
+ compatible = "ti,ads1119";
+ reg = <0x41>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_8>;
+ interrupt-parent = <&main_gpio0>;
+ interrupts = <42 IRQ_TYPE_EDGE_FALLING>;
+ avdd-supply = <®_3v2_ain2>;
+ dvdd-supply = <®_3v2_ain2>;
+ vref-supply = <®_3v2_ain2>;
+ #address-cells = <1>;
+ #io-channel-cells = <1>;
+ #size-cells = <0>;
+
+ /* AIN2 0-33V Voltage Input */
+ channel@0 {
+ reg = <0>;
+ diff-channels = <0 1>;
+ };
+
+ /* AIN2 0-20mA Current Input */
+ channel@1 {
+ reg = <1>;
+ diff-channels = <2 3>;
+ };
+ };
+};
+
+/* Verdin CAN_1 */
+&main_mcan0 {
+ status = "okay";
+};
+
+/* Verdin SPI_1 */
+&main_spi1 {
+ pinctrl-0 = <&pinctrl_spi1>,
+ <&pinctrl_spi1_cs0>,
+ <&pinctrl_gpio_1>,
+ <&pinctrl_gpio_4>;
+ cs-gpios = <0>,
+ <&mcu_gpio0 1 GPIO_ACTIVE_LOW>,
+ <&mcu_gpio0 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm@1 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <1>;
+ spi-max-frequency = <18500000>;
+ };
+
+ fram@2 {
+ compatible = "fujitsu,mb85rs256", "atmel,at25";
+ reg = <2>;
+ address-width = <16>;
+ size = <32768>;
+ spi-max-frequency = <33000000>;
+ pagesize = <1>;
+ };
+};
+
+/* Verdin UART_3 */
+&main_uart0 {
+ status = "okay";
+};
+
+/* Verdin UART_1 */
+&main_uart1 {
+ status = "okay";
+};
+
+&mcu_gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_2>,
+ <&pinctrl_gpio_3>,
+ <&pinctrl_pcie_1_reset>;
+ gpio-line-names =
+ "",
+ "",
+ "GPIO2", /* Verdin GPIO_2 - SODIMM 208 */
+ "GPIO3", /* Verdin GPIO_3 - SODIMM 210 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+};
+
+/* Verdin CAN_2 */
+&mcu_mcan0 {
+ status = "okay";
+};
+
+/* Verdin SD_1 */
+&sdhci1 {
+ status = "okay";
+};
+
+/* Verdin USB_1*/
+&usbss0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbss1 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+/* Verdin PCIE_1_RESET# */
+&verdin_pcie_1_reset_hog {
+ status = "okay";
+};
+
+/* Verdin UART_2 */
+&wkup_uart0 {
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-active-low;
+ rs485-rx-during-tx;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-verdin-nonwifi-ivy.dts b/arch/arm64/boot/dts/ti/k3-am625-verdin-nonwifi-ivy.dts
new file mode 100644
index 000000000000..48798bf3da4f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-verdin-nonwifi-ivy.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
+ * https://www.toradex.com/products/carrier-board/ivy-carrier-board
+ */
+
+/dts-v1/;
+
+#include "k3-am625.dtsi"
+#include "k3-am62-verdin.dtsi"
+#include "k3-am62-verdin-nonwifi.dtsi"
+#include "k3-am62-verdin-ivy.dtsi"
+
+/ {
+ model = "Toradex Verdin AM62 on Ivy Board";
+ compatible = "toradex,verdin-am62-nonwifi-ivy",
+ "toradex,verdin-am62-nonwifi",
+ "toradex,verdin-am62",
+ "ti,am625";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-verdin-wifi-ivy.dts b/arch/arm64/boot/dts/ti/k3-am625-verdin-wifi-ivy.dts
new file mode 100644
index 000000000000..d96d8a0ebd86
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-verdin-wifi-ivy.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
+ * https://www.toradex.com/products/carrier-board/ivy-carrier-board
+ */
+
+/dts-v1/;
+
+#include "k3-am625.dtsi"
+#include "k3-am62-verdin.dtsi"
+#include "k3-am62-verdin-wifi.dtsi"
+#include "k3-am62-verdin-ivy.dtsi"
+
+/ {
+ model = "Toradex Verdin AM62 WB on Ivy Board";
+ compatible = "toradex,verdin-am62-wifi-ivy",
+ "toradex,verdin-am62-wifi",
+ "toradex,verdin-am62",
+ "ti,am625";
+};
--
2.39.5
Powered by blists - more mailing lists