[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1jplotxg8e.fsf@starbuckisacylon.baylibre.com>
Date: Tue, 24 Sep 2024 16:45:37 +0200
From: Jerome Brunet <jbrunet@...libre.com>
To: Xianwei Zhao via B4 Relay <devnull+xianwei.zhao.amlogic.com@...nel.org>
Cc: Neil Armstrong <neil.armstrong@...aro.org>, Michael Turquette
<mturquette@...libre.com>, Stephen Boyd <sboyd@...nel.org>, Rob Herring
<robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor
Dooley <conor+dt@...nel.org>, Chuan Liu <chuan.liu@...ogic.com>, Kevin
Hilman <khilman@...libre.com>, Martin Blumenstingl
<martin.blumenstingl@...glemail.com>, xianwei.zhao@...ogic.com,
linux-amlogic@...ts.infradead.org, linux-clk@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 4/5] clk: meson: add support for the A5 SoC PLL clock
On Sat 14 Sep 2024 at 13:25, Xianwei Zhao via B4 Relay <devnull+xianwei.zhao.amlogic.com@...nel.org> wrote:
> From: Chuan Liu <chuan.liu@...ogic.com>
>
> Add the PLL clock controller driver for the Amlogic A5 SoC family.
>
> Signed-off-by: Chuan Liu <chuan.liu@...ogic.com>
> Signed-off-by: Xianwei Zhao <xianwei.zhao@...ogic.com>
> ---
> drivers/clk/meson/Kconfig | 14 ++
> drivers/clk/meson/Makefile | 1 +
> drivers/clk/meson/a5-pll.c | 553 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 568 insertions(+)
>
> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
> index 78f648c9c97d..2a713276e46c 100644
> --- a/drivers/clk/meson/Kconfig
> +++ b/drivers/clk/meson/Kconfig
> @@ -132,6 +132,20 @@ config COMMON_CLK_A1_PERIPHERALS
> device, A1 SoC Family. Say Y if you want A1 Peripherals clock
> controller to work.
>
> +config COMMON_CLK_A5_PLL
> + tristate "Amlogic A5 PLL clock controller"
> + depends on ARM64
> + default y
> + imply ARM_SCMI_PROTOCOL
don't think this is needed, same as c3
> + imply COMMON_CLK_SCMI
> + select COMMON_CLK_MESON_REGMAP
> + select COMMON_CLK_MESON_PLL
> + select COMMON_CLK_MESON_CLKC_UTILS
> + help
> + Support for the PLL clock controller on Amlogic AV40x device, AKA A5.
> + Say Y if you want the board to work, because PLLs are the parent
> + of most peripherals.
> +
> config COMMON_CLK_C3_PLL
> tristate "Amlogic C3 PLL clock controller"
> depends on ARM64
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index bc56a47931c1..fc4b8a723145 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
> obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
> obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
> +obj-$(CONFIG_COMMON_CLK_A5_PLL) += a5-pll.o
> obj-$(CONFIG_COMMON_CLK_C3_PLL) += c3-pll.o
> obj-$(CONFIG_COMMON_CLK_C3_PERIPHERALS) += c3-peripherals.o
> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
> diff --git a/drivers/clk/meson/a5-pll.c b/drivers/clk/meson/a5-pll.c
> new file mode 100644
> index 000000000000..d96ed72ef8d4
> --- /dev/null
> +++ b/drivers/clk/meson/a5-pll.c
> @@ -0,0 +1,553 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Amlogic A5 PLL Controller Driver
> + *
> + * Copyright (c) 2024 Amlogic, inc.
> + * Author: Chuan Liu <chuan.liu@...ogic.com>
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/platform_device.h>
> +#include "clk-regmap.h"
> +#include "clk-pll.h"
> +#include "clk-mpll.h"
Kconfig does not select support for this, so something is odd.
> +#include "meson-clkc-utils.h"
> +#include <dt-bindings/clock/amlogic,a5-pll-clkc.h>
> +
> +#define ANACTRL_FIXPLL_CTRL1 0x44
> +#define ANACTRL_GP0PLL_CTRL0 0x80
> +#define ANACTRL_GP0PLL_CTRL1 0x84
> +#define ANACTRL_GP0PLL_CTRL2 0x88
> +#define ANACTRL_GP0PLL_CTRL3 0x8c
> +#define ANACTRL_GP0PLL_CTRL4 0x90
> +#define ANACTRL_GP0PLL_CTRL5 0x94
> +#define ANACTRL_GP0PLL_CTRL6 0x98
> +#define ANACTRL_HIFIPLL_CTRL0 0x100
> +#define ANACTRL_HIFIPLL_CTRL1 0x104
> +#define ANACTRL_HIFIPLL_CTRL2 0x108
> +#define ANACTRL_HIFIPLL_CTRL3 0x10c
> +#define ANACTRL_HIFIPLL_CTRL4 0x110
> +#define ANACTRL_HIFIPLL_CTRL5 0x114
> +#define ANACTRL_HIFIPLL_CTRL6 0x118
> +#define ANACTRL_MPLL_CTRL0 0x180
> +#define ANACTRL_MPLL_CTRL1 0x184
> +#define ANACTRL_MPLL_CTRL2 0x188
> +#define ANACTRL_MPLL_CTRL3 0x18c
> +#define ANACTRL_MPLL_CTRL4 0x190
> +#define ANACTRL_MPLL_CTRL5 0x194
> +#define ANACTRL_MPLL_CTRL6 0x198
> +#define ANACTRL_MPLL_CTRL7 0x19c
> +#define ANACTRL_MPLL_CTRL8 0x1a0
> +
> +static DEFINE_SPINLOCK(aml_clk_lock);
Re-submit you lock patch first and adjust please.
> +
> +static struct clk_fixed_factor mpll_prediv = {
> + .mult = 1,
> + .div = 2,
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll_prediv",
> + .ops = &clk_fixed_factor_ops,
> + .parent_data = &(const struct clk_parent_data) {
> + .fw_name = "fix_dco"
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static const struct reg_sequence mpll0_init_regs[] = {
> + { .reg = ANACTRL_MPLL_CTRL2, .def = 0x40000033 },
> +};
> +
> +static struct clk_regmap mpll0_div = {
> + .data = &(struct meson_clk_mpll_data){
> + .sdm = {
> + .reg_off = ANACTRL_MPLL_CTRL1,
> + .shift = 0,
> + .width = 14,
> + },
> + .sdm_en = {
> + .reg_off = ANACTRL_MPLL_CTRL1,
> + .shift = 30,
> + .width = 1,
> + },
> + .n2 = {
> + .reg_off = ANACTRL_MPLL_CTRL1,
> + .shift = 20,
> + .width = 9,
> + },
> + .ssen = {
> + .reg_off = ANACTRL_MPLL_CTRL1,
> + .shift = 29,
> + .width = 1,
> + },
> + .lock = &aml_clk_lock,
> + .init_regs = mpll0_init_regs,
> + .init_count = ARRAY_SIZE(mpll0_init_regs),
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll0_div",
> + .ops = &meson_clk_mpll_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &mpll_prediv.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap mpll0 = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = ANACTRL_MPLL_CTRL1,
> + .bit_idx = 31,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll0",
> + .ops = &clk_regmap_gate_ops,
> + .parent_hws = (const struct clk_hw *[]) { &mpll0_div.hw },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static const struct reg_sequence mpll1_init_regs[] = {
> + { .reg = ANACTRL_MPLL_CTRL4, .def = 0x40000033 },
> +};
> +
> +static struct clk_regmap mpll1_div = {
> + .data = &(struct meson_clk_mpll_data){
> + .sdm = {
> + .reg_off = ANACTRL_MPLL_CTRL3,
> + .shift = 0,
> + .width = 14,
> + },
> + .sdm_en = {
> + .reg_off = ANACTRL_MPLL_CTRL3,
> + .shift = 30,
> + .width = 1,
> + },
> + .n2 = {
> + .reg_off = ANACTRL_MPLL_CTRL3,
> + .shift = 20,
> + .width = 9,
> + },
> + .ssen = {
> + .reg_off = ANACTRL_MPLL_CTRL3,
> + .shift = 29,
> + .width = 1,
> + },
> + .lock = &aml_clk_lock,
> + .init_regs = mpll1_init_regs,
> + .init_count = ARRAY_SIZE(mpll1_init_regs),
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll1_div",
> + .ops = &meson_clk_mpll_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &mpll_prediv.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap mpll1 = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = ANACTRL_MPLL_CTRL3,
> + .bit_idx = 31,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll1",
> + .ops = &clk_regmap_gate_ops,
> + .parent_hws = (const struct clk_hw *[]) { &mpll1_div.hw },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static const struct reg_sequence mpll2_init_regs[] = {
> + { .reg = ANACTRL_MPLL_CTRL6, .def = 0x40000033 },
> +};
> +
> +static struct clk_regmap mpll2_div = {
> + .data = &(struct meson_clk_mpll_data){
> + .sdm = {
> + .reg_off = ANACTRL_MPLL_CTRL5,
> + .shift = 0,
> + .width = 14,
> + },
> + .sdm_en = {
> + .reg_off = ANACTRL_MPLL_CTRL5,
> + .shift = 30,
> + .width = 1,
> + },
> + .n2 = {
> + .reg_off = ANACTRL_MPLL_CTRL5,
> + .shift = 20,
> + .width = 9,
> + },
> + .ssen = {
> + .reg_off = ANACTRL_MPLL_CTRL5,
> + .shift = 29,
> + .width = 1,
> + },
> + .lock = &aml_clk_lock,
> + .init_regs = mpll2_init_regs,
> + .init_count = ARRAY_SIZE(mpll2_init_regs),
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll2_div",
> + .ops = &meson_clk_mpll_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &mpll_prediv.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap mpll2 = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = ANACTRL_MPLL_CTRL5,
> + .bit_idx = 31,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll2",
> + .ops = &clk_regmap_gate_ops,
> + .parent_hws = (const struct clk_hw *[]) { &mpll2_div.hw },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static const struct reg_sequence mpll3_init_regs[] = {
> + { .reg = ANACTRL_MPLL_CTRL8, .def = 0x40000033 },
> +};
> +
> +static struct clk_regmap mpll3_div = {
> + .data = &(struct meson_clk_mpll_data){
> + .sdm = {
> + .reg_off = ANACTRL_MPLL_CTRL7,
> + .shift = 0,
> + .width = 14,
> + },
> + .sdm_en = {
> + .reg_off = ANACTRL_MPLL_CTRL7,
> + .shift = 30,
> + .width = 1,
> + },
> + .n2 = {
> + .reg_off = ANACTRL_MPLL_CTRL7,
> + .shift = 20,
> + .width = 9,
> + },
> + .ssen = {
> + .reg_off = ANACTRL_MPLL_CTRL7,
> + .shift = 29,
> + .width = 1,
> + },
> + .lock = &aml_clk_lock,
> + .init_regs = mpll3_init_regs,
> + .init_count = ARRAY_SIZE(mpll3_init_regs),
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll3_div",
> + .ops = &meson_clk_mpll_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &mpll_prediv.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap mpll3 = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = ANACTRL_MPLL_CTRL7,
> + .bit_idx = 31,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "mpll3",
> + .ops = &clk_regmap_gate_ops,
> + .parent_hws = (const struct clk_hw *[]) { &mpll3_div.hw },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static const struct reg_sequence gp0_init_regs[] = {
> + { .reg = ANACTRL_GP0PLL_CTRL0, .def = 0X08000000 },
> + { .reg = ANACTRL_GP0PLL_CTRL1, .def = 0x00000000 },
> + { .reg = ANACTRL_GP0PLL_CTRL2, .def = 0x00000000 },
> + { .reg = ANACTRL_GP0PLL_CTRL3, .def = 0x6a295c00 },
> + { .reg = ANACTRL_GP0PLL_CTRL4, .def = 0x65771290 },
> + { .reg = ANACTRL_GP0PLL_CTRL5, .def = 0x3927200a },
> + { .reg = ANACTRL_GP0PLL_CTRL6, .def = 0x54540000 }
> +};
> +
> +static const struct pll_mult_range gp0_pll_mult_range = {
> + .min = 125,
> + .max = 250,
> +};
> +
> +static struct clk_regmap gp0_pll_dco = {
> + .data = &(struct meson_clk_pll_data) {
> + .en = {
> + .reg_off = ANACTRL_GP0PLL_CTRL0,
> + .shift = 28,
> + .width = 1,
> + },
> + .m = {
> + .reg_off = ANACTRL_GP0PLL_CTRL0,
> + .shift = 0,
> + .width = 8,
> + },
> + .frac = {
> + .reg_off = ANACTRL_GP0PLL_CTRL1,
> + .shift = 0,
> + .width = 17,
> + },
> + .n = {
> + .reg_off = ANACTRL_GP0PLL_CTRL0,
> + .shift = 10,
> + .width = 5,
> + },
> + .l = {
> + .reg_off = ANACTRL_GP0PLL_CTRL0,
> + .shift = 31,
> + .width = 1,
> + },
> + .rst = {
> + .reg_off = ANACTRL_GP0PLL_CTRL0,
> + .shift = 29,
> + .width = 1,
> + },
> + .range = &gp0_pll_mult_range,
> + .init_regs = gp0_init_regs,
> + .init_count = ARRAY_SIZE(gp0_init_regs),
> + .frac_max = 100000,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "gp0_pll_dco",
> + .ops = &meson_clk_pll_ops,
> + .parent_data = &(const struct clk_parent_data) {
> + .fw_name = "xtal_24m",
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +/* The maximum frequency divider supports is 16, not 128(2^7) */
> +static const struct clk_div_table gp0_pll_od_table[] = {
> + { 0, 1 },
> + { 1, 2 },
> + { 2, 4 },
> + { 3, 8 },
> + { 4, 16 },
> + { 5, 32 },
> + { /* sentinel */ }
> +};
> +
> +static struct clk_regmap gp0_pll = {
> + .data = &(struct clk_regmap_div_data) {
> + .offset = ANACTRL_GP0PLL_CTRL0,
> + .shift = 16,
> + .width = 3,
> + .table = gp0_pll_od_table,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "gp0_pll",
> + .ops = &clk_regmap_divider_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &gp0_pll_dco.hw
> + },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static const struct reg_sequence hifi_init_regs[] = {
> + { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0X08000000 },
What is bit you are flipping in CTRL0 ? it is suspicious
> + { .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x00000000 },
> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00000000 },
> + { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x6a295c00 },
> + { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x65771290 },
> + { .reg = ANACTRL_HIFIPLL_CTRL5, .def = 0x3927200a },
> + { .reg = ANACTRL_HIFIPLL_CTRL6, .def = 0x54540000 }
> +};
> +
> +static const struct pll_mult_range hifi_pll_mult_range = {
> + .min = 125,
> + .max = 250,
> +};
> +
> +static struct clk_regmap hifi_pll_dco = {
> + .data = &(struct meson_clk_pll_data) {
> + .en = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 28,
> + .width = 1,
> + },
> + .m = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 0,
> + .width = 8,
> + },
> + .frac = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL1,
> + .shift = 0,
> + .width = 17,
> + },
> + .n = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 10,
> + .width = 5,
> + },
> + .l = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 31,
> + .width = 1,
> + },
> + .rst = {
> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 29,
> + .width = 1,
> + },
> + .range = &hifi_pll_mult_range,
> + .init_regs = hifi_init_regs,
> + .init_count = ARRAY_SIZE(hifi_init_regs),
> + .frac_max = 100000,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "hifi_pll_dco",
> + .ops = &meson_clk_pll_ops,
> + .parent_data = &(const struct clk_parent_data) {
> + .fw_name = "xtal_24m",
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +/* The maximum frequency divider supports is 16, not 128(2^7) */
> +static const struct clk_div_table hifi_pll_od_table[] = {
> + { 0, 1 },
> + { 1, 2 },
> + { 2, 4 },
> + { 3, 8 },
Why don't you ajust the mask then ? Looks like a POW_OF_2 basic
dividider to me.
> + { /* sentinel */ }
> +};
> +
> +static struct clk_regmap hifi_pll = {
> + .data = &(struct clk_regmap_div_data) {
> + .offset = ANACTRL_HIFIPLL_CTRL0,
> + .shift = 16,
> + .width = 3,
> + .table = hifi_pll_od_table,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "hifi_pll",
> + .ops = &clk_regmap_divider_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &hifi_pll_dco.hw
> + },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + },
> +};
> +
> +static struct clk_hw *a5_pll_hw_clks[] = {
> + [CLKID_MPLL_PREDIV] = &mpll_prediv.hw,
> + [CLKID_MPLL0_DIV] = &mpll0_div.hw,
> + [CLKID_MPLL0] = &mpll0.hw,
> + [CLKID_MPLL1_DIV] = &mpll1_div.hw,
> + [CLKID_MPLL1] = &mpll1.hw,
> + [CLKID_MPLL2_DIV] = &mpll2_div.hw,
> + [CLKID_MPLL2] = &mpll2.hw,
> + [CLKID_MPLL3_DIV] = &mpll3_div.hw,
> + [CLKID_MPLL3] = &mpll3.hw,
> + [CLKID_GP0_PLL_DCO] = &gp0_pll_dco.hw,
> + [CLKID_GP0_PLL] = &gp0_pll.hw,
> + [CLKID_HIFI_PLL_DCO] = &hifi_pll_dco.hw,
> + [CLKID_HIFI_PLL] = &hifi_pll.hw
> +};
> +
> +/* Convenience table to populate regmap in .probe */
> +static struct clk_regmap *const a5_pll_clk_regmaps[] = {
> + &mpll0_div,
> + &mpll0,
> + &mpll1_div,
> + &mpll1,
> + &mpll2_div,
> + &mpll2,
> + &mpll3_div,
> + &mpll3,
> + &gp0_pll_dco,
> + &gp0_pll,
> + &hifi_pll_dco,
> + &hifi_pll
> +};
> +
> +static const struct regmap_config clkc_regmap_config = {
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = ANACTRL_MPLL_CTRL8,
> +};
> +
> +static struct meson_clk_hw_data a5_pll_clks = {
> + .hws = a5_pll_hw_clks,
> + .num = ARRAY_SIZE(a5_pll_hw_clks),
> +};
> +
> +static int aml_a5_pll_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct regmap *regmap;
> + void __iomem *base;
> + int clkid, ret, i;
> +
> + base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + regmap = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
> + if (IS_ERR(regmap))
> + return PTR_ERR(regmap);
> +
> + /* Populate regmap for the regmap backed clocks */
> + for (i = 0; i < ARRAY_SIZE(a5_pll_clk_regmaps); i++)
> + a5_pll_clk_regmaps[i]->map = regmap;
> +
> + for (clkid = 0; clkid < a5_pll_clks.num; clkid++) {
> + /* array might be sparse */
> + if (!a5_pll_clks.hws[clkid])
> + continue;
> +
> + ret = devm_clk_hw_register(dev, a5_pll_clks.hws[clkid]);
> + if (ret) {
> + dev_err(dev, "Clock registration failed\n");
> + return ret;
> + }
> + }
> +
> + return devm_of_clk_add_hw_provider(dev, meson_clk_hw_get,
> + &a5_pll_clks);
> +}
> +
> +static const struct of_device_id a5_pll_clkc_match_table[] = {
> + {
> + .compatible = "amlogic,a5-pll-clkc",
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, a5_pll_clkc_match_table);
> +
> +static struct platform_driver a5_pll_driver = {
> + .probe = aml_a5_pll_probe,
> + .driver = {
> + .name = "a5-pll-clkc",
> + .of_match_table = a5_pll_clkc_match_table,
> + },
> +};
> +module_platform_driver(a5_pll_driver);
> +
> +MODULE_DESCRIPTION("Amlogic A5 PLL Clock Controller driver");
> +MODULE_AUTHOR("Chuan Liu <chuan.liu@...ogic.com>");
> +MODULE_LICENSE("GPL");
--
Jerome
Powered by blists - more mailing lists