| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZvhviRUb/CitmhgQ@x1>
Date: Sat, 28 Sep 2024 14:05:13 -0700
From: Drew Fustini <dfustini@...storrent.com>
To: Andrew Lunn <andrew@...n.ch>,
Emil Renner Berthing <emil.renner.berthing@...onical.com>
Cc: "David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Alexandre Torgue <alexandre.torgue@...s.st.com>,
Giuseppe Cavallaro <peppe.cavallaro@...com>,
Jose Abreu <joabreu@...opsys.com>,
Jisheng Zhang <jszhang@...nel.org>,
Maxime Coquelin <mcoquelin.stm32@...il.com>,
Drew Fustini <drew@...7.com>, Guo Ren <guoren@...nel.org>,
Fu Wei <wefu@...hat.com>, Conor Dooley <conor@...nel.org>,
Paul Walmsley <paul.walmsley@...ive.com>,
Palmer Dabbelt <palmer@...belt.com>,
Albert Ou <aou@...s.berkeley.edu>, netdev@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org,
linux-riscv@...ts.infradead.org
Subject: Re: [PATCH v2 3/3] riscv: dts: thead: Add TH1520 ethernet nodes
On Fri, Sep 27, 2024 at 01:58:40PM +0200, Andrew Lunn wrote:
> > I tried to setup an nfs server with a rootfs on my local network. I can
> > mount it okay from my laptop so I think it is working okay. However, it
> > does not seem to work on the lpi4a [3]. It appears the rgmii-id
> > validation fails and the dwmac driver can not open the phy:
> >
> > thead-dwmac ffe7060000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
> > thead-dwmac ffe7060000.ethernet eth0: validation of rgmii-id with support \
> > 00,00000000,00000000,00006280 and advertisementa \
> > 00,00000000,00000000,00006280 failed: -EINVAL
> > thead-dwmac ffe7060000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -22)
>
> Given what Emil said, i would suggest flipping the MDIO busses
> around. Put the PHYs on gmac1's MDIO bus, and set the pinmux so that
> its MDIO bus controller is connected to the outside world. Then, when
> gmac1 probes first, its MDIO bus will be probed at the same time, and
> its PHY found.
>
> Andrew
I'm trying to configure the pinmux to have gmac1 control the mdio bus
but it seems I've not done so correctly. I changed pins "GMAC0_MDC" and
"GMAC0_MDIO" to function "gmac1" (see the patch below).
I don't see any errors about the dwmac or phy in the boot log [1] but
ultimately there is no carrier detected and the ethernet interface does
not come up.
Section "3.3.4.103 G3_MUXCFG_007" in the TH1520 System User Manual shows
that bits [19:16] control GMAC0_MDIO_MUX_CFG where value of 2 selects
GMAC1_MDIO. Similarly, bits [15:12] control GMAC0_MDC_MUX_CFG where a
value of 2 also selects GMAC1_MDC.
Emil - do you have any suggestion as to what I might be doing wrong with
the pinmux?
Thanks,
Drew
[1] https://gist.github.com/pdp7/1f9fcd76f26acd5715398d54f65a2e27
diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
index ca84bc2039ef..f2f6c9d9b590 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
@@ -11,6 +11,11 @@ / {
model = "Sipeed Lichee Module 4A";
compatible = "sipeed,lichee-module-4a", "thead,th1520";
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
memory@0 {
device_type = "memory";
reg = <0x0 0x00000000 0x2 0x00000000>;
@@ -55,6 +60,22 @@ &sdio0 {
status = "okay";
};
+&gmac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_pins>;
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&gmac1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1_pins>, <&mdio1_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
&gpio0 {
gpio-line-names = "", "", "", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "", "", "",
@@ -87,3 +108,101 @@ &gpio3 {
"GPIO09",
"GPIO10";
};
+
+&mdio1 {
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@2 {
+ reg = <2>;
+ };
+};
+
+&padctrl0_apsys {
+ gmac0_pins: gmac0-0 {
+ tx-pins {
+ pins = "GMAC0_TX_CLK",
+ "GMAC0_TXEN",
+ "GMAC0_TXD0",
+ "GMAC0_TXD1",
+ "GMAC0_TXD2",
+ "GMAC0_TXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <25>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pins = "GMAC0_RX_CLK",
+ "GMAC0_RXDV",
+ "GMAC0_RXD0",
+ "GMAC0_RXD1",
+ "GMAC0_RXD2",
+ "GMAC0_RXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ gmac1_pins: gmac1-0 {
+ tx-pins {
+ pins = "GPIO2_18", /* GMAC1_TX_CLK */
+ "GPIO2_20", /* GMAC1_TXEN */
+ "GPIO2_21", /* GMAC1_TXD0 */
+ "GPIO2_22", /* GMAC1_TXD1 */
+ "GPIO2_23", /* GMAC1_TXD2 */
+ "GPIO2_24"; /* GMAC1_TXD3 */
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <25>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pins = "GPIO2_19", /* GMAC1_RX_CLK */
+ "GPIO2_25", /* GMAC1_RXDV */
+ "GPIO2_30", /* GMAC1_RXD0 */
+ "GPIO2_31", /* GMAC1_RXD1 */
+ "GPIO3_0", /* GMAC1_RXD2 */
+ "GPIO3_1"; /* GMAC1_RXD3 */
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ mdio1_pins: mdio1-0 {
+ mdc-pins {
+ pins = "GMAC0_MDC";
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <13>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ mdio-pins {
+ pins = "GMAC0_MDIO";
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <13>;
+ input-enable;
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+ };
+};
Powered by blists - more mailing lists