| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <b6ec9050339f8244ff898898a1cecc33b13a48fc.1727741563.git.daniel@makrotopia.org>
Date: Tue, 1 Oct 2024 01:17:18 +0100
From: Daniel Golle <daniel@...rotopia.org>
To: Xu Liang <lxu@...linear.com>, Andrew Lunn <andrew@...n.ch>,
Heiner Kallweit <hkallweit1@...il.com>,
Russell King <linux@...linux.org.uk>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
David Bauer <mail@...id-bauer.net>,
Christian Marangi <ansuelsmth@...il.com>,
John Crispin <john@...ozen.org>, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH net-next] net: phy: mxl-gpy: add basic LED support
Add basic support for LEDs connected to MaxLinear GPY2xx and GPY115 PHYs.
The PHYs allow up to 4 LEDs to be connected.
Implement controlling LEDs in software as well as netdev trigger offloading
and LED polarity setup.
The hardware claims to support 16 PWM brightness levels but there is no
documentation on how to use that feature, hence this is not supported.
Signed-off-by: Daniel Golle <daniel@...rotopia.org>
---
Changes since RFC:
- only clear hw-control registers when brightness is set to LED_OFF
- add ToDo comment about setting PWM brightness level (missing documentation)
- first setup hw-control modes and then switch on hw-control in
gpy_led_hw_control_set()
- white space fixes
- use reverse xmas-tree order for variable declarations
drivers/net/phy/mxl-gpy.c | 218 ++++++++++++++++++++++++++++++++++++++
1 file changed, 218 insertions(+)
diff --git a/drivers/net/phy/mxl-gpy.c b/drivers/net/phy/mxl-gpy.c
index d7d4755d6635..6279f88c4979 100644
--- a/drivers/net/phy/mxl-gpy.c
+++ b/drivers/net/phy/mxl-gpy.c
@@ -38,6 +38,7 @@
#define PHY_MIISTAT 0x18 /* MII state */
#define PHY_IMASK 0x19 /* interrupt mask */
#define PHY_ISTAT 0x1A /* interrupt status */
+#define PHY_LED 0x1B /* LEDs */
#define PHY_FWV 0x1E /* firmware version */
#define PHY_MIISTAT_SPD_MASK GENMASK(2, 0)
@@ -61,6 +62,11 @@
PHY_IMASK_ADSC | \
PHY_IMASK_ANC)
+#define GPY_MAX_LEDS 4
+#define PHY_LED_POLARITY(idx) BIT(12 + (idx))
+#define PHY_LED_HWCONTROL(idx) BIT(8 + (idx))
+#define PHY_LED_ON(idx) BIT(idx)
+
#define PHY_FWV_REL_MASK BIT(15)
#define PHY_FWV_MAJOR_MASK GENMASK(11, 8)
#define PHY_FWV_MINOR_MASK GENMASK(7, 0)
@@ -72,6 +78,23 @@
#define PHY_MDI_MDI_X_CD 0x1
#define PHY_MDI_MDI_X_CROSS 0x0
+/* LED */
+#define VSPEC1_LED(idx) (1 + (idx))
+#define VSPEC1_LED_BLINKS GENMASK(15, 12)
+#define VSPEC1_LED_PULSE GENMASK(11, 8)
+#define VSPEC1_LED_CON GENMASK(7, 4)
+#define VSPEC1_LED_BLINKF GENMASK(3, 0)
+
+#define VSPEC1_LED_LINK10 BIT(0)
+#define VSPEC1_LED_LINK100 BIT(1)
+#define VSPEC1_LED_LINK1000 BIT(2)
+#define VSPEC1_LED_LINK2500 BIT(3)
+
+#define VSPEC1_LED_TXACT BIT(0)
+#define VSPEC1_LED_RXACT BIT(1)
+#define VSPEC1_LED_COL BIT(2)
+#define VSPEC1_LED_NO_CON BIT(3)
+
/* SGMII */
#define VSPEC1_SGMII_CTRL 0x08
#define VSPEC1_SGMII_CTRL_ANEN BIT(12) /* Aneg enable */
@@ -848,6 +871,156 @@ static int gpy115_loopback(struct phy_device *phydev, bool enable)
return genphy_soft_reset(phydev);
}
+static int gpy_led_brightness_set(struct phy_device *phydev,
+ u8 index, enum led_brightness value)
+{
+ int ret;
+
+ if (index >= GPY_MAX_LEDS)
+ return -EINVAL;
+
+ /* clear HWCONTROL and set manual LED state */
+ ret = phy_modify(phydev, PHY_LED,
+ ((value == LED_OFF) ? PHY_LED_HWCONTROL(index) : 0) |
+ PHY_LED_ON(index),
+ (value == LED_OFF) ? 0 : PHY_LED_ON(index));
+ if (ret)
+ return ret;
+
+ /* ToDo: set PWM brightness */
+
+ /* clear HW LED setup */
+ if (value == LED_OFF)
+ return phy_write_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_LED(index), 0);
+ else
+ return 0;
+}
+
+static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_LINK) |
+ BIT(TRIGGER_NETDEV_LINK_100) |
+ BIT(TRIGGER_NETDEV_LINK_1000) |
+ BIT(TRIGGER_NETDEV_LINK_2500) |
+ BIT(TRIGGER_NETDEV_RX) |
+ BIT(TRIGGER_NETDEV_TX));
+
+static int gpy_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ if (index >= GPY_MAX_LEDS)
+ return -EINVAL;
+
+ /* All combinations of the supported triggers are allowed */
+ if (rules & ~supported_triggers)
+ return -EOPNOTSUPP;
+
+ return 0;
+}
+
+static int gpy_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ int val;
+
+ if (index >= GPY_MAX_LEDS)
+ return -EINVAL;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_LED(index));
+ if (val < 0)
+ return val;
+
+ if (FIELD_GET(VSPEC1_LED_CON, val) & VSPEC1_LED_LINK10)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_10);
+
+ if (FIELD_GET(VSPEC1_LED_CON, val) & VSPEC1_LED_LINK100)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_100);
+
+ if (FIELD_GET(VSPEC1_LED_CON, val) & VSPEC1_LED_LINK1000)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_1000);
+
+ if (FIELD_GET(VSPEC1_LED_CON, val) & VSPEC1_LED_LINK2500)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_2500);
+
+ if (FIELD_GET(VSPEC1_LED_CON, val) == (VSPEC1_LED_LINK10 |
+ VSPEC1_LED_LINK100 |
+ VSPEC1_LED_LINK1000 |
+ VSPEC1_LED_LINK2500))
+ *rules |= BIT(TRIGGER_NETDEV_LINK);
+
+ if (FIELD_GET(VSPEC1_LED_PULSE, val) & VSPEC1_LED_TXACT)
+ *rules |= BIT(TRIGGER_NETDEV_TX);
+
+ if (FIELD_GET(VSPEC1_LED_PULSE, val) & VSPEC1_LED_RXACT)
+ *rules |= BIT(TRIGGER_NETDEV_RX);
+
+ return 0;
+}
+
+static int gpy_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 val = 0;
+ int ret;
+
+ if (index >= GPY_MAX_LEDS)
+ return -EINVAL;
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK) ||
+ rules & BIT(TRIGGER_NETDEV_LINK_10))
+ val |= FIELD_PREP(VSPEC1_LED_CON, VSPEC1_LED_LINK10);
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK) ||
+ rules & BIT(TRIGGER_NETDEV_LINK_100))
+ val |= FIELD_PREP(VSPEC1_LED_CON, VSPEC1_LED_LINK100);
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK) ||
+ rules & BIT(TRIGGER_NETDEV_LINK_1000))
+ val |= FIELD_PREP(VSPEC1_LED_CON, VSPEC1_LED_LINK1000);
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK) ||
+ rules & BIT(TRIGGER_NETDEV_LINK_2500))
+ val |= FIELD_PREP(VSPEC1_LED_CON, VSPEC1_LED_LINK2500);
+
+ if (rules & BIT(TRIGGER_NETDEV_TX))
+ val |= FIELD_PREP(VSPEC1_LED_PULSE, VSPEC1_LED_TXACT);
+
+ if (rules & BIT(TRIGGER_NETDEV_RX))
+ val |= FIELD_PREP(VSPEC1_LED_PULSE, VSPEC1_LED_RXACT);
+
+ /* allow RX/TX pulse without link indication */
+ if ((rules & BIT(TRIGGER_NETDEV_TX) || rules & BIT(TRIGGER_NETDEV_RX)) &&
+ !(val & VSPEC1_LED_CON))
+ val |= FIELD_PREP(VSPEC1_LED_PULSE, VSPEC1_LED_NO_CON) | VSPEC1_LED_CON;
+
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_LED(index), val);
+ if (ret)
+ return ret;
+
+ return phy_set_bits(phydev, PHY_LED, PHY_LED_HWCONTROL(index));
+}
+
+static int gpy_led_polarity_set(struct phy_device *phydev, int index,
+ unsigned long modes)
+{
+ bool active_low = false;
+ u32 mode;
+
+ if (index >= GPY_MAX_LEDS)
+ return -EINVAL;
+
+ for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+ switch (mode) {
+ case PHY_LED_ACTIVE_LOW:
+ active_low = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ return phy_modify(phydev, PHY_LED, PHY_LED_POLARITY(index),
+ active_low ? 0 : PHY_LED_POLARITY(index));
+}
+
static struct phy_driver gpy_drivers[] = {
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY2xx),
@@ -865,6 +1038,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
.phy_id = PHY_ID_GPY115B,
@@ -883,6 +1061,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy115_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY115C),
@@ -900,6 +1083,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy115_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
.phy_id = PHY_ID_GPY211B,
@@ -918,6 +1106,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY211C),
@@ -935,6 +1128,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
.phy_id = PHY_ID_GPY212B,
@@ -953,6 +1151,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY212C),
@@ -970,6 +1173,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
.phy_id = PHY_ID_GPY215B,
@@ -988,6 +1196,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY215C),
@@ -1005,6 +1218,11 @@ static struct phy_driver gpy_drivers[] = {
.set_wol = gpy_set_wol,
.get_wol = gpy_get_wol,
.set_loopback = gpy_loopback,
+ .led_brightness_set = gpy_led_brightness_set,
+ .led_hw_is_supported = gpy_led_hw_is_supported,
+ .led_hw_control_get = gpy_led_hw_control_get,
+ .led_hw_control_set = gpy_led_hw_control_set,
+ .led_polarity_set = gpy_led_polarity_set,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_GPY241B),
--
2.46.2
Powered by blists - more mailing lists