| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20241002-b4-master-24-11-25-ov08x40-v3-4-483bcdcf8886@linaro.org>
Date: Wed, 02 Oct 2024 14:58:46 +0100
From: Bryan O'Donoghue <bryan.odonoghue@...aro.org>
To: Sakari Ailus <sakari.ailus@...ux.intel.com>,
Jason Chen <jason.z.chen@...el.com>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Sergey Senozhatsky <senozhatsky@...omium.org>,
Hans Verkuil <hverkuil-cisco@...all.nl>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: linux-media@...r.kernel.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, Bryan O'Donoghue <bryan.odonoghue@...aro.org>
Subject: [PATCH v3 4/4] media: ov08x40: Add OF probe support
The ACPI version of this driver "just works" on dts based systems with a
few extensions to facilitate.
- Add support for DT based probing
- Add support for taking the part out of reset via a GPIO reset pin
- Add in regulator bulk on/off logic for the power rails.
Once done this sensor works nicely on a Qualcomm X1E80100 CRD.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@...aro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@...aro.org>
---
drivers/media/i2c/ov08x40.c | 138 +++++++++++++++++++++++++++++++++++++++-----
1 file changed, 124 insertions(+), 14 deletions(-)
diff --git a/drivers/media/i2c/ov08x40.c b/drivers/media/i2c/ov08x40.c
index 3ab8b51df157af78fcccc1aaef73aedb2ae759c9..821102287580acecd544402254cfe0fb5c8dc299 100644
--- a/drivers/media/i2c/ov08x40.c
+++ b/drivers/media/i2c/ov08x40.c
@@ -3,10 +3,13 @@
#include <asm-generic/unaligned.h>
#include <linux/acpi.h>
+#include <linux/clk.h>
#include <linux/i2c.h>
+#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
#include <media/v4l2-ctrls.h>
#include <media/v4l2-device.h>
#include <media/v4l2-fwnode.h>
@@ -1279,6 +1282,12 @@ static const struct ov08x40_mode supported_modes[] = {
},
};
+static const char * const ov08x40_supply_names[] = {
+ "dovdd", /* Digital I/O power */
+ "avdd", /* Analog power */
+ "dvdd", /* Digital core power */
+};
+
struct ov08x40 {
struct v4l2_subdev sd;
struct media_pad pad;
@@ -1291,6 +1300,10 @@ struct ov08x40 {
struct v4l2_ctrl *hblank;
struct v4l2_ctrl *exposure;
+ struct clk *xvclk;
+ struct gpio_desc *reset_gpio;
+ struct regulator_bulk_data supplies[ARRAY_SIZE(ov08x40_supply_names)];
+
/* Current mode */
const struct ov08x40_mode *cur_mode;
@@ -1303,6 +1316,61 @@ struct ov08x40 {
#define to_ov08x40(_sd) container_of(_sd, struct ov08x40, sd)
+static int ov08x40_power_on(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov08x40 *ov08x = to_ov08x40(sd);
+ int ret;
+
+ if (is_acpi_node(dev_fwnode(dev)))
+ return 0;
+
+ ret = clk_prepare_enable(ov08x->xvclk);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable xvclk\n");
+ return ret;
+ }
+
+ if (ov08x->reset_gpio) {
+ gpiod_set_value_cansleep(ov08x->reset_gpio, 1);
+ usleep_range(1000, 2000);
+ }
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(ov08x40_supply_names),
+ ov08x->supplies);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable regulators\n");
+ goto disable_clk;
+ }
+
+ gpiod_set_value_cansleep(ov08x->reset_gpio, 0);
+ usleep_range(1500, 1800);
+
+ return 0;
+
+disable_clk:
+ gpiod_set_value_cansleep(ov08x->reset_gpio, 1);
+ clk_disable_unprepare(ov08x->xvclk);
+
+ return ret;
+}
+
+static int ov08x40_power_off(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov08x40 *ov08x = to_ov08x40(sd);
+
+ if (is_acpi_node(dev_fwnode(dev)))
+ return 0;
+
+ gpiod_set_value_cansleep(ov08x->reset_gpio, 1);
+ regulator_bulk_disable(ARRAY_SIZE(ov08x40_supply_names),
+ ov08x->supplies);
+ clk_disable_unprepare(ov08x->xvclk);
+
+ return 0;
+}
+
/* Read registers up to 4 at a time */
static int ov08x40_read_reg(struct ov08x40 *ov08x,
u16 reg, u32 len, u32 *val)
@@ -2072,7 +2140,7 @@ static void ov08x40_free_controls(struct ov08x40 *ov08x)
mutex_destroy(&ov08x->mutex);
}
-static int ov08x40_check_hwcfg(struct device *dev)
+static int ov08x40_check_hwcfg(struct ov08x40 *ov08x, struct device *dev)
{
struct v4l2_fwnode_endpoint bus_cfg = {
.bus_type = V4L2_MBUS_CSI2_DPHY
@@ -2086,11 +2154,36 @@ static int ov08x40_check_hwcfg(struct device *dev)
if (!fwnode)
return -ENXIO;
- ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
- &xvclk_rate);
- if (ret) {
- dev_err(dev, "can't get clock frequency");
- return ret;
+ if (!is_acpi_node(fwnode)) {
+ ov08x->xvclk = devm_clk_get(dev, NULL);
+ if (IS_ERR(ov08x->xvclk)) {
+ dev_err(dev, "could not get xvclk clock (%pe)\n",
+ ov08x->xvclk);
+ return PTR_ERR(ov08x->xvclk);
+ }
+
+ xvclk_rate = clk_get_rate(ov08x->xvclk);
+
+ ov08x->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(ov08x->reset_gpio))
+ return PTR_ERR(ov08x->reset_gpio);
+
+ for (i = 0; i < ARRAY_SIZE(ov08x40_supply_names); i++)
+ ov08x->supplies[i].supply = ov08x40_supply_names[i];
+
+ ret = devm_regulator_bulk_get(dev,
+ ARRAY_SIZE(ov08x40_supply_names),
+ ov08x->supplies);
+ if (ret)
+ return ret;
+ } else {
+ ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+ &xvclk_rate);
+ if (ret) {
+ dev_err(dev, "can't get clock frequency");
+ return ret;
+ }
}
if (xvclk_rate != OV08X40_XVCLK) {
@@ -2143,32 +2236,37 @@ static int ov08x40_check_hwcfg(struct device *dev)
}
static int ov08x40_probe(struct i2c_client *client)
-{
- struct ov08x40 *ov08x;
+{ struct ov08x40 *ov08x;
int ret;
bool full_power;
+ ov08x = devm_kzalloc(&client->dev, sizeof(*ov08x), GFP_KERNEL);
+ if (!ov08x)
+ return -ENOMEM;
+
/* Check HW config */
- ret = ov08x40_check_hwcfg(&client->dev);
+ ret = ov08x40_check_hwcfg(ov08x, &client->dev);
if (ret) {
dev_err(&client->dev, "failed to check hwcfg: %d", ret);
return ret;
}
- ov08x = devm_kzalloc(&client->dev, sizeof(*ov08x), GFP_KERNEL);
- if (!ov08x)
- return -ENOMEM;
-
/* Initialize subdev */
v4l2_i2c_subdev_init(&ov08x->sd, client, &ov08x40_subdev_ops);
full_power = acpi_dev_state_d0(&client->dev);
if (full_power) {
+ ret = ov08x40_power_on(&client->dev);
+ if (ret) {
+ dev_err(&client->dev, "failed to power on\n");
+ return ret;
+ }
+
/* Check module identity */
ret = ov08x40_identify_module(ov08x);
if (ret) {
dev_err(&client->dev, "failed to find sensor: %d\n", ret);
- return ret;
+ goto probe_power_off;
}
}
@@ -2210,6 +2308,9 @@ static int ov08x40_probe(struct i2c_client *client)
error_handler_free:
ov08x40_free_controls(ov08x);
+probe_power_off:
+ ov08x40_power_off(&client->dev);
+
return ret;
}
@@ -2224,6 +2325,8 @@ static void ov08x40_remove(struct i2c_client *client)
pm_runtime_disable(&client->dev);
pm_runtime_set_suspended(&client->dev);
+
+ ov08x40_power_off(&client->dev);
}
#ifdef CONFIG_ACPI
@@ -2235,10 +2338,17 @@ static const struct acpi_device_id ov08x40_acpi_ids[] = {
MODULE_DEVICE_TABLE(acpi, ov08x40_acpi_ids);
#endif
+static const struct of_device_id ov08x40_of_match[] = {
+ { .compatible = "ovti,ov08x40" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov08x40_of_match);
+
static struct i2c_driver ov08x40_i2c_driver = {
.driver = {
.name = "ov08x40",
.acpi_match_table = ACPI_PTR(ov08x40_acpi_ids),
+ .of_match_table = ov08x40_of_match,
},
.probe = ov08x40_probe,
.remove = ov08x40_remove,
--
2.46.2
Powered by blists - more mailing lists